Page 1
g.1
B
D
C
g.3
A
g.2
g.4 g.5
g.6
g.9
g.8
g.10
g.13
g.14
g.7
g.12
g.11
ASSEMBLY INSTRUCTIONS
N!ERGY PORTABLE CANOPY
Component List: 1 Canopy Top, 1 Frame Assembly, 1 Carry Bag
w/Wheels, 1 Pre-Installed Wiring Harness w/ Switch, 4 Nailhead
Stakes, 4 Guy Out Skewers, 4 Attached Guy Out Cords
NOTE:
Do not drop carry bag. Do not bounce the bag on its end to get
the frame out. These actions may damage the electrical components.
Although it is possible to raise this structure by yourself; it is much easier
and faster if you have help.
Rev B 4.09
Expand the Frame:
• Open the carry bag, remove the frame and top. Lay the top aside and
stand the frame up, near its final location
• With one person at A and another at B, lift the poles and step back to
pull the legs out and away from the center. See fig. 1. Move to C and D
and again lift and pull the
legs out and away. Work
back and forth between
AB and CD, until the
frame is extended as
shown in g. 2
• If you are working alone,
pull the frame apart as
best you can and then
drive a nailhead stake
through the hole in the
baseplate of one of the
legs. See g. 3. Work your
way from corner, pulling
out and away from the
staked leg
• Continue until the frame
is extended as shown in
g. 2
Raise the Perimeter and
Roof Rafters:
• At each corner, lift the
bottom section of the
perimeter rafter until the
lock button on the leg
clicks into its seat in the
collar. See g. 4 & 5. Take
care that the collar truly
captures the button,
otherwise the roof will
slide back down.
• Continue with the rest of
the perimeter rafters
until all corners are
locked in place and the
roof is extended as
shown in g. 6
Secure the Structure to the Ground:
• Drive a nailhead stake through the
holes in the baseplates at the
bottom of the legs. See fig. 12
• Use the skewers to stake
the guyout cords and
adjust tension with the
attached sliders. See g. 13
Attach the Canopy Top to the Frame:
• Lay the fabric on the ground with the top facing
up and square to the frame.
• Grasp the two canopy corners closest to the frame
and drag them up and over the roof to the frame
corners on the opposite side. Take care that the
electrical plugs do not get caught on the frame as
you tug the canopy
• At each corner, fit the fabric snug to the frame.
Align the guy gusset to the top of the frame and
at a 45˚ angle from the leg. See fig. 7
• Move inside, under the canopy. Wrap each pair of
Velcro® hook pads from the inside corners of the
canopy to the loops near the top of the corner
poles. See g. 8
• Attach all remaining Velcro® tabs to the perimeter
and roof rafters. See fig. 9
Raise the Legs:
• Station one person
at each leg on one
side of the frame.
Lift the legs and
press the button on
the black collar to
release the inside
section. See g. 10.
Allow the inside
sections to fall to one of the three lock
points. Make sure that the legs are the
same height and that they are locked in
place. See g.11
• Repeat with the remaining two legs
YOUR CANOPY IS READY!
green
blue
E! Power System: To use, you will need a power source. Our E! Power Pak™ is sold
separately. Once connected to power, the control will display “green” at any switch
that is “ON” and the “ON” socket will glow blue. See g 14
Take Down: Pull up all stakes. Release the
canopy’s hook & loop straps and remove
from the frame. You may leave the wire
harness in place. Collapse all poles and stow.
Fold the canopy onto itself, roll up.and stow.
Read the important safety instructions on the
reverse side.
Page 2
REV B FEB .09
LIMITED WARRANTY FOR THE N!ERGY PORTABLE CANOPY:
Johnson Outdoors Gear LLC Portable Canopies are warranted to the original purchaser that
they are free from major defects in materials or workmanship for one year, except as
qualified below. We are not responsible for normal wear and tear or for damages caused
by shipping, accidents, misuse, alterations, or improper installations. Additionally, although
we manufacture Johnson Outdoors Gear LLC products with quality fabrics, we are not
responsible for the negative effects of climate, pollution, acts of God, and long or
semi-permanent installations. Because these shelters are temporary structures, it is
necessary that any Johnson Outdoors Gear LLC shelter be installed and maintained
according to the manufacturer’s instructions.
What Johnson Outdoors Gear LLC Will Do:
If after inspection we find that a product failed due to a manufacturing or material defect,
we will repair or replace the product, at our option, without charge.
How to Obtain Warranty Service:
Return the product, freight prepaid, to the Dealer from whom it was purchased; or, contact
our Customer Satisfaction Department for return authorization: toll free 1-800-572-8822.
Collect shipments or shipments without return authorization cannot be accepted. The
product registration card packaged with our product need not be returned for the
warranty to be effective and for you to receive warranty service.
THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE TERMS OF TH IS LIMITED
WARRANTY. IN NO EVENT SHALL JOHNSON OUTDOORS GEAR LLC BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
How State Law Relates To This Warranty:
This warranty gives you specific legal rights, and you may have other rights that vary from
state to state.
CAUTION:
Good judgment and common sense must be used for each installation and take down.
Since weather is unpredictable, it is the responsibility of the individual installing the shelter
to determine the proper time and method to install, secure and dismantle the shelter.
Johnson Outdoors Gear LLC shelter products are manufactured for use as temporary
protection from sun and light rain. Evacuate the shelter in threatening or severe weather.
WARNING:
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS SHELTER FABRIC.
This shelter meets the flammability requirements of CPAI-84. The fabric may burn
if left in continuous contact with any flame source. The application of any foreign
substance to the fabric may render the flame-resistant properties ineffective.
To learn more… WWW.LNT.ORG
LEAVE NO TRACE
Seven General Principles
1. PLAN AHEAD AND PREPARE
2. TRAVEL & CAMP ON DURABLE SURFACES
3. DISPOSE OF WASTE PROPERLY
4. LEAVE WHAT YOU FIND
5. MINIMIZE CAMPFIRE IMPACTS
6. RESPECT WILDLIFE
7. BE COURTEOUS OF OTHER VISITORS
SAFETY INFORMATION: IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
electric shock and fire hazard
JOHNSON OUTDOORS GEAR LLC
Save these instructions. This manual contains important safety and operating instructions
applicable to the safe and efficient use of the E! Power Pak. Failure to use the power pack in any
way other than originally intended by Johnson Outdoors Gear LLC will void the warranty and may
damage the unit or result in injury. Use of an attachment not recommended or sold by Johnson
Outdoors Gear LLC may result in risk of fire, electric shock, injury to persons, or property damage.
The E! Power Pak is not intended for use by children at any time.
DO NOT
insert any foreign objects into the 12v outlet on the E! Power Pak, or the 12v outlets in the shelter
DO NOT
expose the E! Power Pak or 12v outlets in the shelter to water, rain, snow or spray.
DO NOT
connect any device with a neutral conductor (via an AC inverter) to the E! Power Pak or 12v
outlets.
DO NOT
use the E! Power Pak if it is damaged. Use care not to drop the unit. A drop or fall can damage the
unit even though no visible damage may be apparent.
DO NOT
expose the E! Power Pak to temperatures over 104˚F/40˚C. Always store the E! Power Pak in a dry
environment. Ideal storage temperature is 70˚F/21˚ C.
DO NOT
permit the battery in the E! Power Pak to freeze. Never attempt to recharge a frozen battery.
DO NOT
disassemble the E! Power Pak. Incorrect reassembly may result in a risk of electric shock or fire. If
your E! Power Pak requires service, call Schumacher Electric at 1-800-621-5485.
If your E! Power Pak requires service, call Schumacher Electric at 1-800-621-5485.
Loading...