E.T. Systems E PAD User Manual

BY

2

Ver.201105.007

Operating voltage 12 – 24V AC or DC

Max. Standby current 100mA VDC

Lock and Aux relay rating 3A @15VDC

Weather resistance IP65

Max. user memory Lock relay 98 user codes

Max. user memory Aux. relay 1 user codes

Max. Load on alarm output. 100mA VDC (Open collector)

3

Ver.201105.007

PLEASE TAKE NOTE BEFORE COMMENCING WITH PROGRAMMING!

Master code:

 The master code is used to access programming mode. (Default master code = 1234)
 The master code can be 4 to 8 digits in length.
 The number of digits used for the master code will determine the length of all user codes (Lock, Aux and bypass

users) i.e. the default master code is 1234 so therefore all user codes will be 4 digits long.

 If the master code length is changed after user codes have already been programmed, the following will

occur.
Master code shortened – the last digits of the user code will be dropped making the user codes the same length

as the master code.

I.e. the old master code was 123456 and user 01 was 987654.
New master is 1234. User 01 becomes 9876.
Master code length increased – zeros will be added to the end of all user codes so that the user codes are

equal in length to the master code.

I.e. old master code was 1234 and user 01 was 9876.
New master code = 123456. User 01 becomes 987600

 Keep a record of all codes and never attempt to program a duplicate of another code already in the keypad.
I.e. user 01 code cannot be the same as the master code.

Other points to note before programming

 You cannot enter programming mode if one of the relays is active.
 You cannot enter programming mode if the tamper switch is active. Close up the keypad housing first.
 To exit programming, at any stage, press the # key.

How to, setup the keypad for use by up to 20 users.

Setup a new master code: (Default = 1234)

Current Master Code + Current Master Code

(chime tone up)

+ * + 00 + New 4 to 8 digit Master Code + #

(chime tone up)

I.e. To change the master code to 4321:- 1234 1234

*

00 4321 #

Setup user codes 01 to 19 that activate the lock relay: (User 01 default = 3333)

Master Code + Master Code

(chime tone up)

+ * + two digit user number + New User Code

(chime tone up)

I.e. To setup a single user code (example user 01 to 8282): - 1234 1234

*

01 8282 #

I.e. To setup multiple user codes: - 1234 1234

*

01 8282

*

02 2222

*

03 3333……..#

Setup code to activate the Auxiliary relay output: (Default = 9999)

NB! When programming a new code for the Auxiliary relay, the new code replaces the old code, with no need to erase

the old code.
Master Code + Master Code

(chime tone up)

+ * + 40 + New Auxiliary Code

(chime tone up)

+ #

I.e. To setup Aux relay code to 2222:- 1234 1234

*

40 2222 #

4

Ver.201105.007

Deleting Lock relay output user codes:

Deleting an individual user code;

Master Code + Master Code

(chime tone up)

+ * + 50 + two digit user number

(chime tone up)

+ #

Deleting all user codes; (user 01 defaults to 3333)

Master Code + Master Code

(chime tone up)

+ * + 50 + 00

(chime tone up

) + #

Setup type or pulse length of Lock relay output: (Default = 1 sec.)

Set for Latch mode;

Master Code + Master Code

(chime tone up)

+ * + 20 + 00

(chime tone up)

+ #

Set for pulse mode and set pulse length;

Master Code + Master Code

(chime tone up)

+ * + 20 + 01 for 1 sec…….99 for 99sec

(chime tone up)

+ #

Setup type or pulse length of Auxiliary relay: (Default = latch mode)

Set for Latch mode;
Master Code + Master Code

(chime tone up)

+ * + 58 + 000

(chime tone up)

#

Set for Pulse mode and pulse length;
Master Code + Master Code

(chime tone up)

+ * + 58 + 001 for 1 sec, 002 for 2 sec………999 for 999 sec

(chime tone up)

+ #

Activate the incorrect code attempt lock out: (Default = disabled)

Keypad disables keystrokes for 30 sec. after 5 incorrect code entries or if 20 consecutive incorrect keystrokes have been
entered. NB! Typing # between keystrokes restarts the incorrect keystroke counter.

Master Code + Master Code

(chime tone up)

+ * + 51

(chime tone up)

+ #

Repeat this to de-activate again.

Activate the Bypass code option :( Default = Deactivated)

NEVER USE WITH SOLENOID TYPE STRIKERS or LOCKS!

When the Bypass code is entered the Lock relay latches on until the bypass code is re-entered or when the door release
button is activated.

Master Code + Master Code

(chime tone up)

+ * + 52 + 1

(chime tone up)

+ #

Deactivating the bypass mode option:
Master Code + Master Code

(chime tone up)

+ * + 52 + 0

(chime tone up)

+ #

Setup bypass code: (Default = none)

Master Code + Master Code

(chime tone up)

+ * + 54 + New unique bypass code

(chime tone up)

+ #

5

Ver.201105.007

Default the Keypad to factory default settings:

NB! All factory settings and codes will be restored to the default values and all previously programmed user codes will
be erased.

Power the E Pad down.
Open the unit to access PCB
Place jumper in the “system restore” position.
Power the E Pad up.
At continuous tone, remove and replace jumper in original position.
Replace and secure cover.

LED Statuses

Power LED

Green Lock Relay

LED

Amber Aux Relay

LED

Red =

Normal

mode

On = Relay active On = Relay active

Yellow =

Programming

mode

Off = Standby Off = Standby

Flashing = Door
alarm memory.

Enter user code

twice to clear.

6

Ver.201105.007

ADVANCED PROGRAMMING OPTIONS AND QUICK REFERENCE TABLE.

Need Action

Factory

Default

Response

Buzzer

Enter programming mode Master code + Master code 1234

Chime tone up

Master and user codes

Change master code

*

00 + new master code (4-8 digits) Note the number of digits the

master is set to will be the number of digits all user codes, lock, aux and
bypass.

No chime tone

Set user codes 01 ~ 19 (Lock relay
output only)

*

01~ 19 + new unique user code (Same length as master code)

User 01 =

3333

Chime tone up

Set user codes 20 ~ 39 and 41 ~ 99
(Lock relay output only)

*

6 + 2 digit user number + new unique user code (Same length as

master code)

Chime tone up

Set user code 40 (Aux relay output
only)

*

40 + new unique aux user code (Same length as master code)

9999

Chime tone up

Keypad lockout on multiple incorrect
code attempts.

*

51 to change status on or off.

De-

activated

Chime tone up

Delete a user code or all user codes. (If
deleting all user 01 defaults to 3333)

*

50 + 00 for all, 01 for user 1, 02 for user 2………………….99 for user 99.

Chime tone up

Relays

Select Lock relay type or pulse length.

*

20 + 00 = latch mode or 01 for 1 sec, 02 for 2 sec………99 for 99 sec

1 sec.

Chime tone up

Select Aux relay type or pulse length

*

58 + 000 = latch mode or 001 for 1 sec, 002 for 2 sec………..999 for 999

sec.

Latch

Chime tone up

Bypass

mode

Enable bypass mode.

*

52 + 1

Disabled

Chime tone up

Disable bypass mode.

*

52 + 0

Default

Chime tone up

Setup bypass code

*

54 + new unique bypass code

None

Chime tone up

Alarm modes

Disable alarm output mode

*

55 + 0

Disabled

Chime tone up

Select alarm output to activate on
door forced open condition

*

55 + 1 (Door open time limited to equal Lock relay on time)

Not

selected

Chime tone up

Select alarm output to activate on
tamper switch

*

55 + 2

Not

selected

Chime tone up

Select alarm output to activate on
both door forced and tamper switch

*

55 + 3

Not

selected

Chime tone up

Select Alarm output active time

*

56 + 001 for 1 sec, 002 for 2 sec………..999 for 999 sec.

Chime tone up

Auxiliary modes

Disable Aux output

*

57 + 0

Enabled

Chime tone up

Allocate door monitor to work with
Aux output

*

57 + 1

Not

Allocated

Chime tone up

Activate Aux output when multiple
incorrect codes have been entered

*

57 + 2 (Not operational if Aux relay has been set to latch)

Not

Selected

Chime tone up

Activate Aux output when * key is
pressed (Doorbell function)

*

57 + 3

Not

Selected

Chime tone up

Activate Aux output when tamper is
activated

*

57 + 4

Not

Selected

Chime tone up

Activate Aux output when door is
forced open

*

57 + 5

Not

Selected

Chime tone up

Activate Aux output together with lock
output

*

57 + 6

Not

Selected

Chime tone up

Aux output only activates when Aux
code is entered

*

57 + 7

Default

Chime tone up

Factory

default

Factory default Power down
Place jumper across the system restore pins
Power up

Continuous chime

On continuous chime remove jumper and replace it in normal operation
position.

7

Ver.201105.007

Using the keypad

Normal operation:-

To activate the lock relay, simply type in a valid code for that relay or press and release the free exit push button if one
has been installed:

-The lock relay will activate as it was setup by the installer.

-The green LED indicator will activate as per the relay.

To activate the auxiliary relay, simply type in the valid code for that relay:

-The auxiliary relay will activate as it was setup by the installer.

-The yellow auxiliary LED will activate as per the relay.

Alarm monitoring conditions:-

If the alarm monitoring has been set up by the installer, the following will occur.
Alarm output, built in buzzer and flashing green LED will activate immediately an alarm condition occurs.

The follow are alarm conditions available:

 Door opened without a valid code entry first. (Door forced alarm)
 Door not closed by the time the lock relay resets. (Door kept open alarm)
 Keypad housing opened. (Tamper alarm)

After the alarm time (set by the installer) has expired, the alarm output and the built in buzzer resets. However, the
flashing green LED continues until the first valid user code is entered into the keypad. This way the user is made aware
that an alarm condition occurred even after the built in buzzer and alarm output have reset.

Bypass function:-

NEVER USE WITH SOLENOID TYPE STRIKERS or LOCKS!

In cases such as an office park or school gate, that need to temporarily be kept open to allow for peak traffic periods,
the bypass function can be used. This function requires a dedicated code which is set up by the master code holder.

When the bypass code is entered, the lock relay will latch on until either the bypass code is entered again or the free
exit push button is pressed.

While the bypass function is active, no other lock relay user code will release the relay.

This function is also useful where a magnetic lock is installed.

8

Ver.201105.007

WARRANTY: All goods manufactured by G&C Electronics cc T/A ET Systems carry a 12 month factory warranty from date
of invoice. All goods are warranted to be free of faulty components and manufacturing defects. Faulty goods will be
repaired or replaced at the sole discretion of ET Systems free of charge. This warranty is subject to the goods being
returned to the premises of ET Systems. The carriage of goods is for the customer’s account. This warranty is only valid if
the correct installation and application of goods, as laid out in the applicable documentation accompanying said
goods, is adhered to. All warranty claims must be accompanied by the original invoice. All claims made by the end
user must be directed to their respective service provider/installer from whom they purchased the product.

The following conditions will disqualify this product from the warranty as laid out above.

These conditions are non-negotiable.

 Any unauthorized non-manufacturer modifications to the product or components thereof.
 Incorrect voltage range used
 Incorrect loads applied to the relays

9

Ver.201105.007

Cape Town (Southern Suburbs)

15 Nelson Road, Observatory, Cape Town, 7925

Tel: [phone] – Fax: [phone] – Email: [e-mail]

Cape Town (Northern Suburbs)

Unit 5, 2 Kiewiet Close, Okavango, Brackenfell

Tel: [phone] – Fax: [phone] – Email: [e-mail]

Port Elizabeth

12 Parkin Street, North End, Port Elizabeth, 6001

Tel: [phone] – Fax: [phone] – Email: [e-mail]

Durban

Unit 6, 24 Alexander Road, Westmead, Pinetown, 3610

Tel: [phone] – Fax: [phone] – Email: [e-mail]

Gauteng

Unit 2, Keymax Park, Samrand, 102 Stirling Road, Kosmosdal x12, Centurion

Tel: [phone] – Fax: [phone] – Email: [e-mail]

Nelspruit

Unit 12, 25 Rapid street West, Riverside Industrial Park, Riverside, 1200

Tel: [phone] – Fax: [phone] – Email: [e-mail]

National Share call Number

0860 109 238

Website

www.et.co.za