Page 1
Archived 3/23/10
EQUIPMENT MANUAL
HIGH POWER BICONICAL ANTENNA
EMCO MODEL 3108
Page 2
Archived 3/23/10
399037
Revision B
Page 3
WARRANTY
Archived 3/23/10
The Electro-Mechanics Company (EMCO) warrants that our products are free from
defects in materials and workmanship for a period of two years from the date of
shipment. If you notify us of a defect within the warranty period, we will, at our
option, either repair or replace those products which prove to be defective. If
applicable, we will also recalibrate the product.
There will be no charge for warranty services performed at the location we
designate. You must however, prepay inbound shipping costs and any duties or
taxes. We will pay outbound shipping costs for a carrier of our choice, exclusive of
any duties or taxes. You may request warranty services to be performed at your
location, but it is our option to do so. If we determine that warranty service can only
be performed at your location, you will not be charged for our travel related costs.
This warranty does not apply to:
1. Normal wear and tear of materials
2. Consumable items such as fuses, batteries, etc.
3. Products which have been improperly installed, maintained, or used.
4. Products which have been operated outside of specifications.
5. Products which have been modified without authorization.
6. Calibration of products, unless necessitated by defects.
THIS WARRANTY IS EXCLUSIVE. NO OTHER WARRANTY, WRITTEN OR ORAL,
IS EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
THE REMEDIES PROVIDED BY THIS WARRANTY ARE YOUR SOLE AND
EXCLUSIVE REMEDIES. IN NO EVENT ARE WE LIABLE FOR ANY DAMAGES
WHATSOEVER, INCLUDING BUT NOT LIMITED TO, DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED
ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY.
Please contact our Sales Department for a Return Material Authorization Number
before shipping equipment to us.
Page 4
TABLE OF CONTENTS
Archived 3/23/10
Warranty
Description and Use / Specifications
Table 1 - Typical Antenna Factor and Gain
Figure 1 - Typical VSWR vs Frequency
Figure 2 - Typical Antenna Radiation Pattern 100 MHz Vertical
Figure 3 - Typical Antenna Radiation Pattern 100 MHz Horizontal
Photo of Model 3108
Assembly Instruction
Shipping List
Page 5
DESCRIPTION AND USE OF THE
Archived 3/23/10
EMCO MODEL 3108 HIGH POWER BICONICAL ANTENNA
General Description
The EMCO Model 3108 High Power Biconical Antenna is designed to operate over
the 30 to 300 MHz frequency range for measurements in accordance with present
and proposed DoD and Military EMI specifications. Its ability to handle large power
levels over a broadband make the 3108 excellent for use in Radiated Susceptibility
as well as Radiated Emission testing.
The lightweight breakdown construction of the Model 3108 makes for ease of
storage and portability. The biconical elements are made from tack welded
aluminum rods. The 4 to 1 balun network is fabricated from TFE thermoplastics
and silver plated brass and aluminum.
The Model 3108 is manufactured in accordance with ECOM drawings
ES-DL-176433 and ES-F-201286. Each antenna is individually calibrated during
manufacturing. The Gain and Antenna Factors for the individual antenna are
tabulated and included in this manual for use in Specification Compliance Testing.
Refer to Table 1 for Typical Antenna Factor and Gain.
Refer to Figure 1 for Typical VSWR vs Frequency.
Refer to Figure 2 and 3 for Typical Antenna Radiation Pattern.
Specifications
Frequency Range: 30 to 300 MHz
Impedance: Matched to 50 Ohms
Connector: Type N
Power Input Capability: 300 Watts Continuous Power
500 Watts Short Term Peak Power
Assembled Dimensions:
Length: 51.8 inches (131.6 cm)
Diameter: 20.5 inches (52 cm)
Weight: 6 lb (2.7 kg)
NOTE: EMCO recommends using a 6 db pad attached to the end of the
antenna, otherwise high VSWR may occur.
Loading...