10.3 Communications Regulation Information ............................................................174
5
FCC Caution
1. The device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions:
2. This device may not cause harmful interference, and this device must accept any
interference received, including interference that may cause undesired operation.
3. FCC RF Radiation Exposure Statement: The equipment complies with FCC RF radiation
exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
4. This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
5. Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment.
6
Safe Seating Gestures
You should follow the manufacturer’s instructions for adjusting the backrest to fit your body
properly.
An adjustable chair that provides firm, comfortable support is best.
Adjust the height of the chair so your thighs are horizontal and your feet flat on the floor.
The back of the chair should support your lower back (lumbar region).
CE Statement of Conformity
Our product has been tested in typical configuration by Ecom Sertech Corp and was found to
comply with the essential requirement of “Council Directive on the Approximation of the Laws
of the Member States relating to Electromagnetic Compatibility” (89/336/EEC; 92/31/EEC;
93/68/EEC)
Notice
Changing RF parameter is not allowed.
7
Chapter 1 Introduction
1.1 Overview
11N Broadband router is huge in functionality. It provides wired ethernet and wireless WiFi
interfaces for different needs. It has auto-detect to make plug and play more easy.
8
1.2 Features
y Small in size but huge in functionality; the world No.1 Mobile Router for traveler
y Three modes to be switched; Router, AP and WiFi AP
y WPS button provides not only an easy and secured wireless network but also a WDS
repeater in one push
yMultiple APs Supported; adds or limits the properties for classed SSID, increasing the
Operating Humidity 10% to 85% Non-Condensing
Storage Humidity 5% to 90% Non-Condensing
Power Supply
Power Adapter DC5V/0.6A
Note: 1. Firmware Upgrade available through download.
10
1.3.1 Views of Product Appearance
Power Plug
Operation Mode
Switch
Reset Button
Ethernet Port
Power Adapter DC5V/0.6A
Router, AP, and WiFi AP operation mod es
Press “Reset” button over 10 seconds. When status indicator turns from
flashing to solid, the process is completed. All settings are back to default.
5 RJ-45 Ethernet 10/100 Ports
1.3.2 LED Indicator Status Description
LED Function ColorStatusDescription
Power x 1
System status
Green
On System is ready to work
1. Power is being applied and system
Blinking
boot in progress
120ms
2. Reset or firmware upgrade in progress
Wireless / WPS
Wireless activity
Green
On Wireless is connected
11
x 1
&
WPS status
Blinking
Wireless Tx/Rx activity
30ms
WAN x 1
LAN x 4
WAN port activity
LAN port activity
Reddish
Orange
Green
Green
Green
Green
Blinking
WPS function in progress
120ms
On 100Mbps Ethernet is connected
Blinking
100Mbps Ethernet Tx/Rx activity
30ms
On 10Mbps Ethernet is connected
Blinking
10Mbps Ethernet Tx/Rx activity
120ms
On 100Mbps Ethernet is connected
Blinking
100Mbps Ethernet Tx/Rx activity
30ms
On 10Mbps Ethernet is connected
Blinking
10Mbps Ethernet Tx/Rx activity
120ms
1.4 System Requirements
To begin with 11N Broadband router, you must have the following minimum system
requirements. If your system can’t correspond to the following requirements, you might get
some unknown troubles on your system.
XDSL/Cable Modem and broadband Internet Account.
One Ethernet (10 BASE-T or 10/100 BASE-TX) network interface card.
PC and at least one web browser software installed (E.g.: Internet Explorer 5.0,
Netscape Navigator 7.x, Apple Safari 2.03 or higher version).
At lease one 802.11b, 802.11g, or 802.11n wireless adapter for wireless clients.
Recommended OS: Windows 2000, Windows XP, Windows Vista, Windows 7 / Linux.
12
1.5 WAN Network Plug and Play
WAN Type auto-detection:
When using Ethernet auto-connection:
¾ Auto-detection mode only applies on PPPoE, DHCP, PPTP and L2TP.
¾ Router will detect WAN type and load the settings from last time or display
corresponding page for user to input information.
¾If there is no setting from user, the router will load the default settings.
If there is no setting from user, it will detect ISP and load corresponding settings.
1.6 Get Your IP Automatically & Manually
After 11N Broadband router connected with your computer, please make sure your IP is in the
automatic IP position or you adjust it manually in order to activate the Internet network from
home to Internet. If you don’t know how to enter the settings, please follow the steps as
below.
Step 1. Go to Start>Settings> Network Connections and then select Local Area
Connection.
Step 2. Click on Properties
13
Step 3. Double click on Internet Protocol (TCP/IP).
Step 4-1. For getting IP automatically if you are one of the users under 11N Broadband router , please skip Use the following IP address and then select Obtain an IP address
automatically and Obtain DNS server address automatically and then click on OK button.
14
Step 4-2. For getting IP manually in order to specify a Virtual Server, such as Print Server,
FTP Server and so on, please skip Obtain an IP address automatically and then select Use the following IP address. And the following default setting of 11N Broadband router should
be noted:
y IP Address: 192.168.1.10 (as your Print Server for example)
y Subnet Mask: 255.255.255.0
y Default Gateway: 192.168.1.1
Note: If you configure your computer’s IP Address manually, it needs to be on the same network segment.
For example:
z IP Address: 192.168.1.xxx (xxx can be any number between 2 and 253, but it can’t be
repeated, we use 100 to be the example.)
z Subnet Mask: 255.255.255.0
z Gateway: 192.168.1.1 (this is the IP address of 11N Broadband router in Router Mode)
z DNS: 192.168.1.1 (use 11N Broadband router’s IP address or on your own choice)
Note: IP address and Default gateway cannot be the same.
15
1.6.1 Network Testing
There are two ways to test your Network whether it can work on Internet or not. They are
“Testing with Internet Browser” and “Testing with Dos”.
1.6.2 Testing with Internet Browser
Open an Internet Browser, such as Internet Explore or Netscape. Input a valid web address
you like, for example,
enter. If the website appears, that means your Internet is working under normal situation.
http://www.yahoo.comin the web address blank and then press
1.6.2.1 Testing with DOS (Windows XP Platform)
Step 1. Go to start -> Run.
16
Step 2. Input cmd in the blank, and then click OK button. The Command Prompt window
appears.
Step 3. Input ipconfig in the flashing area then press enter. You will get an IP Address
192.168.1.100, for example, and Default Gateway as 192.168.1.1.
Step 4. Ping a legal WAN Address such as 192.168.1.1. If Internet works, it will show Reply
from 192.168.1.1: bytes = 32 time = 3ms TTL =64, for example.
17
If it can’t work, it will show Request timed out.
18
Chapter 2 Hardware Installation
2.1 Diagram of Connecting Hardware to 11N Broadband router
11N Broadband router is a portable and convenient wireless solution for the traveling
businessmen delivering 802.11n wireless connectivity with a maximum wireless signal rate of
up to 300Mbps. Use it in conference rooms, hotel rooms, or even at hotspots. The Wireless
Pocket Router/AP might be small in size, but is huge in functionality, supporting multiple
operation modes, including Access Point (AP) mode, Router mode, and WiFi AP mode. You
can switch among these modes easily by using 11N Broadband router's 3-way configuration
slide switch.
Warning: Before sliding the switch modes, please power-off the router firstly. Moreover, please stay over 10
seconds between power-off / power-on condition.
2.1.1 Hardware Connection and Application for Router Mode
When 11N Broadband router switches to Router Mode, there will be each WAN and LAN port
existing, the administrator can do the Quick Setup including WAN Setup, LAN Setup,
Wireless Setup, Time Server Setup, Password Setup, Firewall Setup, QoS Setup.
19
2.1.2 Hardware Connection and Application for AP Mode
Under AP Mode, it supports 2 LAN ports as Bridge, and user can connect to 11N Broadband
Router via LAN port. The administrator can set up quickly, including LAN Setup, Wireless
Setup, Time Server Setup, and Password Setup.
2.1.3 Hardware Connection and Application for Wi-Fi AP Mode
As WiFi AP Mode, 11N Broadband Router will be a bridge and supports a wireless LAN.
The administrator can set up quickly, including LAN Setup, Wireless Setup, Time Server
Setup, and Password Setup.
20
21
Chapter 3 One Button Setup
The advanced One Button Setup provides users a simple way to set up the complicated
network. Instead of numbers of IPs to be memorized, you just need to fill in some necessary
information and then enjoy the secured internet by clicking the “Finished” button.
3.1 One Button Setup configuration for Router Mode
Step 1. Please plug in power.
The default UPnP of 11N Broadband Router is ON.
22
Step 2. Click the Internet Gateway Device to open the login page.
Step 3. Click One Button Setup on the left of the main menu under router mode.
23
Time Zone Select: Select your time zone from the Time Zone drop-down list. Change Password: For changing password, please fill the password information into
the blank.
Device Name: Name your device here. The default is 11N_Mini_Router.
Note: System will automatically copy the last 6 numbers of this device’s MAC address after your device name.
WAN Interface Setup: Select the WAN Interface from the drop-down list.
WAN Type Setup: Please choose the access type. Wireless Setup: Fill in the ESSID if it is blank, and your prefer Encryption type. The
default is 11N_Mini_Router. Finished: Click finished button to complete the setting.
3.2 One Button Setup configuration for AP Mode
24
Step 1. Please plug in power.
Step 2. Click the Internet Gateway Device to open the login page.
Step 3. Click One Button Setup on the left of the main menu under AP mode.
25
Time Zone Select: Select your time zone from the Time Zone drop-down list.
Change Password: For changing password, please fill the password information into
the blank.
Device Name: Name your device here. The default is 11N_Mini_Router.
Note: System will automatically copy the last 6 numbers of this device’s MAC address after your device name.
Wireless Setup: Define the SSID, and Encryption type.
Finished: Please click finished button to complete the setting.
3.3 One Button Setup configuration for WiFi AP Mode
Step 1. Please plug in power.
Step 2.
Click the Internet Gateway Device to open the login page.
26
Step 3. Click One Button Setup on the left of the main menu under WiFi AP mode.
27
Time Zone Select: Select your time zone from the Time Zone drop-down list.
Change Password: For changing password, please fill the password information into
the blank.
Device Name: Name your device here. The default is 11N_Mini_Router.
Note: System will automatically copy the last 6 numbers of this device’s MAC address after your device name.
Wireless Site Survey Setting: Select the preferred AP for connection, and the
encryption type.
Extended Wireless Setup: Define the ESSID, and Encryption type.
Finished: Please click finished button to complete the setting.
28
Note: One Button Setup is not completed unless users finish all settings and click Finished button.
29
Chapter 4 Basic Setup
Open a Microsoft Internet Explorer, Mozilla Firefox or Apple Safari browser, and enter
http://192.168.1.1 (Default Gateway) into browser’s blank.
The default values for User Name and Password are admin (all in lowercase letters). Click
Login to enter.
30
Loading...
+ 70 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.