Wireless Site Survey Setting ................................................................................. 45
FCC Regulation and Rules
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for this an uncontrolled
environment. The antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter. End users must follow the specific operating instructions for
satisfying RF exposure compliance.
Part 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation
Part 15.21
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Part 15.105
For a Class B digital device or peripheral, the instructions furnished the user shall include the following
or similar statement, placed in a prominent location in the text of the manual:
§ 2.1077 Compliance information.
(a) If a product must be tested and authorized under a Declaration of Conformity, a compliance
information statement shall be supplied with the product at the time of marketing or importation,
containing the following information:
(1) Identification of the product, e.g., name and model number;
(2) A statement, similar to that contained in § 15.19(a)(3) of this chapter, that the product complies with
part 15 of this chapters; and
(3) The identification, by name, address and telephone number, of the responsible party, as defined in
§2.909. The responsible party for a Declaration of Conformity must be located within the United
States.
(b) If a product is assembled from modular components that, by themselves, are authorized under a
Declaration of Conformity and/or a grant of certification, and the assembled product is also subject to
authorization under a Declaration of Conformity but, in accordance with the applicable regulations,
does not require additional testing, the product shall be supplied, at the time of marketing or
importation, with a compliance information statement containing the following information:
(1) Identification of the assembled product, e.g., name and model number.
(2) Identification of the modular components used in the assembly. A modular component authorized
under a Declaration of Conformity shall be identifier as specified in paragraph (a)(1) of this section. A
modular component authorized under a grant of certification shall be identified by name and model
number(if applicable)along with the FCC Identifier number.
(3) A statement that the product complies with part 15 of this chapter.
(4) The identification, by name, address and telephone number, of the responsible party who
assembled the product from modular components, as defined in § 2.909. The responsible party for a
Declaration of Conformity must be located within the Unit States.
(5) Copies of the compliance information statements for each modular component used in the system
that is authorized under a Declaration of Conformity.
(c) The compliance information statement shall be included in the user’s manual or as a separate
sheet.
Chapter 1 Navi R130g’s Router Mode Quick Setup
1.1 Router Mode’s Quick Setup Instruction
Please switch the slide to “Router Mode” as the below instruction:
Then please open a Microsoft Internet Explorer, and enter http://192.168.100.1
(Default Gateway) into browser’s blank, then you will see the configuration page
below:
Please input in the blanks, the factory default values for User Name and Password
are “admin” and “admin” (all in lowercase letters); after inputting, please click on
“OK” to enter the homepage as below:
1.2 The Introduction of Router mode’s Quick Setup
After you go to the main page of “Router Quick Setup”, please click on “Next”
right side below, and go to the next page to do each setting step by step:
1.2.1 Time Zone Setting
The section provides to change the Time. However, change the router’s date and
time does not affect the date and time on your PCs.
Please click on “Next” button to connect to next step.
Please select your
time Zone
1.2.2 LAN Interface Setup
If you are using the Mini Router with multiple PCs on your LAN, please set up this
function for multiple users to connect it. The default LAN IP for R130g is
192.168.100.1.
Please click on “Next” button to connect to next step.
1.2.3 WAN Interface Setup
R130g supports 4 connection types to WAN, select one of the WAN connection
modes required by your ISP in below “WAN Access Type” page, the WAN setting
pages will differ depending on what kind of WAN Type you select.
Please click on “Next” button to connect to next step.
1.2.3.1 WAN Interface Setup–
Static IP
Choose Static IP Address if all WAN IP information is provided to you by your ISP.
R330g will not accept the IP address if it is not in this format, and the blanks of
“IP Address”, “Subnet Mask” and “Default Gateway” must be input.
DNS also needs to be inputted,,,,otherwise you can use the
domain name.
Please click on “Next” button to connect to next step.
Input the data provided
Input the data provided
Input the data provided
by ISP
by ISP
by ISP
1.2.3.2 WAN Interface Setup– DHCP Client
Choose DHCP Client to obtain IP address information automatically from your ISP.
Select this option if your ISP does not give you any IP numbers to use.
Please click on “Next” button to connect to next step.
1.2.3.3 WAN Interface Setup– PPPoE
If your ISP uses PPPoE connection, your ISP will provide you with a username and
password.
Please click on “Next” button to connect to next step.
1.2.3.4 WAN Interface Setup– PPTP
Some DSL service providers supply a special DSL modem in Europe or Big Pond
Cable in Australia. This kind of modem only supports the PPTP tunnel to access
the Internet; Please enter the account’s information of Account and Password
which provided by your ISP.
IP Address, Server IP
Address and Subnet Mask are
all input as necessary.
Please click on “Next” button to connect to next step.
Loading...
+ 32 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.