ETHINK KL8-3H Series, KL8-3H-CAA6, KL8-3H-BAA6 Programming Instructions Manual
KL8-3H-CAA6/KL8-3H-BAA6
www.ethink
-
spa.com
1
KL8-3H PROGRAMMING INSTRUCTIONS
1．key note
Figure 1.1: Conventional panel structure
Figure 1.3: with TV / DVD's DC12V power mask map
“ ” Frequency up-searching / Minute
“ ” Frequency down- searching/ Hour
+
“
” Volume up
“ ”The total on/off & setting confirm
“ ”Radio / CD input key
Blower on/ Off & Temperature Mode Shift
KL8-3H-CAA6/KL8-3H-BAA6
www.ethink
-
spa.com
2
-
“
“ ” Radio memory / lock button
“ ” Radio searching / setting
“ ”Long circulation cleaning
“ ”Preheat setting & Heater On/ Off “ ”Temperature setting key
Note:
Only part of the blue button in the shutdown state in order to operate.
”Volume down
“ ”Pool lights key
“ ”Surf pump 1 key
“ ”Surf pump 2 key
“ ” Setting Of circulation Cleaning & pump 3
2．Functional overview
1、6KW features the largest heating thermostat, pre-heating function, temperature
display and setting function.
2、Surf up to three pumps（KL8-3H-CAA6），a circulating pump, a pump typhoon.
3、Synchronous multi-color light color and the bottom set features light and ozone.
4、CD audio input capabilities. Radio frequency display, and access to 10 channels.
5、87 shows the volume and volume adjustable.
6、Long cycle time cycle of cleaning and cleaning function.
7、24-hour clock display and setting function.
8、With all the settings down memory parameters.
9、Fahrenheit and Celsius temperature switch function.
10、Water anti-freeze function.
11、Backlight function keys.
12、Board computer function key lock.
13、Three-phase or single phase, optional 110-120VAC or 220-240VAC.
14、When the use of "CD" when there is all the way synchronous AC power output for
DVD or TV
15、Three power control mode.
3．Instructions
1、When the initial power，semi-bright backlight，LCD displays the current clock，and display the
current temperature，such as sensor open / short circuit shows “E1”。 Parts of the radio frequency
display shows “- - -” indicates that the system is turned off， pre-heating and cleaning cycle in a
closed state。
Figure 3： normal temperature display Figure 4： Sensor Open / Short show
KL8-3H-CAA6/KL8-3H-BAA6
www.ethink
-
spa.com
3
2、Lock operation:
This feature is optional for function，30 minutes without key operation or shutdown state click
“ ”Key，key lock to start。
In the “LOCKED (key lock)” state， even by the second“ ”Key to open the lock button，
then“LOCKED” signs disappear。
3、The operation of the clock settings:
In the waiting state and pre-heating & circulation cleaning is no setting up or no working ，Press
“ ”or“ ”Key to enter the clock settings，and at this time “：” symbol is no longer
flashing，and the hours and minutes appear flashing。
In the clock settings，and every time“ ”Button to increase the 1 hour， press and hold
“ ”Key will be for increased hours。 Hour adjustment range is：0 ~ 23。
In the clock settings，and every time“ ” Key，increased by 1 minute，hold down the
“ ” Key will be for increased minutes。Minute adjustment range：0 ~ 59。
Set up to wait for 6 seconds after the completion of the system clock set automatically from the
state。
4、Set up the operation of circulation cleaning:
Can only be set once a day circulation cleaning cycle。Set whether or not to start the clean cycle?
In the LCD can be at a glance。See the figure below：
Figure 5：Set the closure of cleaning cycle Figure 6：Clean cycle set to open
all the settings of circulation cleaning must be in the waiting state，at this time will be displayed on
the LCD“- - -”。
1） 、press“ ”Key，enter the circulation cleaning settings, and at this time on the LCD“ ”
Show，At the same time，“CYCLE” flashing signs appear，and one clock is flash，but “：”
no flashing，The flashing clock is “Circulation clean start time”（see Note 2）。Again“ ”
Key，related Closed settings（see Note 1）。
2） 、Press “ ”(Minutes keys) and“ ”(Hours key) that can change “Circulation clean
start time”。 Every time“ ” Key，increased by 1 minute，hold down the“ ” Key
will be for increased minutes。
Every time“ ” Button to increase the 1 hour，press and hold“ ” Key will be for
Loading...