EtherWan SDR-480 series Specifications

SPECIFICATION

MODEL

DC VO LTAG E

RATED CURRENT

CURRENT RANGE

RATED POWER

PEAK CURRENT

PEAK POWER

OUTPUT

INPUT

PROTECTION

FUNCTION

ENVIRONMENT

SAFETY &

EMC

(Note 4)

NOTE

RIPPLE & NOISE (max.)

VOLTAGE ADJ. RANGE

VOLTAGE TOLERANCE Note.3

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

HOLD UP TIME (Typ.)

VOLTAGE RANGE

FREQUENCY RANGE

POWER FACTOR (Typ.)

EFFICIENCY (Typ.)

AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

OVERLOAD

OVER VOLTAGE

OVER TEMPERATURE

DC OK REALY CONTACT RATINGS (max.)

WORKING TEMP.
WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

SAFETY STANDARDS

WITHSTAND VOLTAGE

ISOLATION RESISTANCE
EMC EMISSION

EMC IMMUNITY

MTBF

DIMENSIONOTHERS

PACKING

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.

5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power.
In case the adjacent device is a heat source, 15mm clearance is recommended.

6. 3 seconds peak power max. and the average output power should not exceed the rate power.

7. Derating may be needed under low input voltage. Please check the derating curve for more details.

8. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃

480W Single Output Industrial DIN RAIL with PFC Function

■ Features :



High efficiency 94% and low power dissipation

150% peak load capability
Built-in active PFC function, PF>0.94
Protections: Short circuit / Overload / Over voltage / Over temperature
Cooling by free air convection
Built-in constant current limiting circuit
Can be installed on DIN rail TS-35/7.5 or 15
UL 508(industrial control equipment)approved
EN61000-6-2(EN50082-2) industrial immunity level
Built-in DC OK relay contact
100% full load burn-in test
3 years warranty

PQ

S

E

M

I

F

4

7

SDR-480-24

24V

20A

0 ~ 20A

480W

30A

Note.6

720W (3sec.)

Note.2

100mVp-p

24 ~ 28V

±1.2%
±0.5%
±1.0%

1500ms, 150ms/230VAC 3000ms, 150ms/115VAC at full load

14ms/230VAC at full load

90 ~ 264VAC 127 ~ 370VDC

Note.7

47 ~ 63Hz

0.94/230VAC 0.99/115VAC at full load

94%

5A/115VAC 2.5A/230VAC
40A/115VAC 80A/230VAC

<0.8mA / 240VAC

Normally works within 110 ~ 150% rated output power for more than 3 seconds and then shut down o/p voltage with auto-recovery

>150% rated power, constant current limiting with auto-recovery within 2 seconds and may cause to shut down if over 2 seconds

29 ~ 33V
Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery

Shut down o/p voltage, recovers automatically after temperature goes down

60Vdc/0.3A, 30Vdc/1A, 30Vac/0.5A resistive load

-25 ~ +70 (Refer to "Derating Curve")℃

Note.5

20 ~ 95% RH non-condensing

-40 ~ +85 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 50 )

Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6

UL508, TUV EN60950-1 approved ; (meet EN60204-1)

, EAC TP TC 004

I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25 / 70% RH℃

Compliance to EN55011, EN55032 (CISPR32), EN61204-3 Class B, EN61000-3-2,-3, EAC TP TC 020

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), EN61204-3, heavy industry level, criteriaA,

EAC TP TC 020, SEMI F47, GL approved

112.9K hrs min. MIL-HDBK-217F (25 )℃

85.5*125.2*128.5mm (W*H*D)

1.6Kg; 8pcs/13.8Kg/0.9CUFT

SDR-480-48

48V

10A

0 ~ 10A

480W

15A

120mVp-p

48 ~ 55V

±1.0%
±0.5%
±1.0%

56 ~ 65V

GL

SDR-480 series

Bauar

tgepruft

Sicherheit

egel gema
od

os

be

wac g

www.

tuv.com

ID 2000000000

File Name:SDR-480-SPEC 2018-01-12

480W Single Output Industrial DIN RAIL with PFC Function

SDR-480 series

Mechanical Specification

85.5

ADMISSIBLE DIN-RAIL:TS35/7.5 ORTS35/15

Case No.984A Unit:mm

128.5

125.2

TB2

1
2
3
4

DC OK

5
6
7
8

TB1

+

+VADJ

DC OK

1

2

3

Terminal Pin No. Assignment (TB1)

Pin No.

Assignment

1

FG

2

35

AC/N

3

AC/L

Terminal Pin No. Assignment (TB2)

Pin No.

Assignment

DC OUTPUT +V

1,2

DC OUTPUT -V

3,4

Relay Contact

5,6
7,8

NC

Block Diagram

I/P

FG

EMI FILTER

&

RECTIFIERS

CONTROL

DC OK Relay Contact

Contact Close PSU turns on / DC OK.

Contact Open

Contact Ratings (max.)

PSU turns off / DC Fail.

30V/1A resistive load.

PFC

CIRCUIT

PFC

O.L.P.U.V.P.

POWER

SWITCHING

PWM & P FC

CONTROL

RECTIFIERS

&

FILTER

DC OK

+V

-V

O.C.P.

DETECTION

CIRCUIT

O.V.P.

File Name:SDR-480-SPEC 2018-01-12