Hardened PoE Ethernet Switch
Quick Start Guide
This quick start guide describes how to install and use the
Hardened PoE Ethernet Switch. This is the switch of choice
for harsh environments constrained by space.
Physical Description
The Terminal Block and Power inputs
Power Input Assignment
Power3 48VDC DC Jack
＋
48VDC
Power2
Power1
Relay Alarm Assignment
－
＋
－
Power
Ground
48VDC
Power
Ground
Earth
Ground
1
Terminal
Block
Hardened PoE Ethernet Switch
*Relay warning signal disable for
following:
The relay contact closes if Power1
FAULT
and Power2 are both failed but
Power3 on.
The relay contact closes if Power3
is failed but Power1 and Power2
are both on.
DC Terminal Block Power Inputs: There are two pairs of
power inputs can be used to power up this switch. Redund ant
power supplies function is supported.
The 10/100Base-TX and 100Base-FX Connectors
1. The 10/100Base-TX Connections
The following lists the pinouts of 10/100Base-TX ports.
Pin Regular Ports Uplink port
1 Output Transmit Data + Input Receive Data +
2 Output Transmit Data - Input Receive Data 3 Input Receive Data + Output Transmit Data +
4 NC NC
5 NC NC
6 Input Receive Data - Output Transmit Data 7 NC NC
8 NC NC
2. The 100Base-FX Connections
The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx
(receive) port of device I to the Tx (transmit) port of device II.
2
Hardened PoE Ethernet Switch
3. The WDM 100Base-FX Connections
The fiber port pinouts: Only one single-mode optical fiber is
required to transmit and receive data.
The Port Status LEDs
3
Hardened PoE Ethernet Switch
LED State Indication
10/100Base-TX, 100Base-FX
Link/ACT
(Green)
Steady A valid network connection established.
Flashing
Transmitting or receiving data.
ACT stands for ACTIVITY.
4
Hardened PoE Ethernet Switch
Functional Description
• Meets IEC61000-6-2 EMC Generic Standard Immunity
for industrial environment.
• Supports IEEE802.3af Power over Ethernet (PoE)
Power Sourcing Equipment (PSE).
• Supports IEEE802.3/802.3u/802.3x. Auto-negotiation:
10/100Mbps, Full/Half-duplex, Auto-Negotiation, Auto
MDI/MDIX.
• 100Base-FX: Multi/Single mode SC or ST type, WDM
Single mode SC type.
• Supports 1024 MAC addresses. Provides 1M bits buffer
memory.
• Alarms for power and port link failure by relay output.
• Power Supplies: Redundant 48VDC Terminal Block
power inputs and 48VDC DC JACK with 100-240VAC
external power supply.
• Operating voltage and Max. current consumption: 1.5A
@ 48VDC. Power consumption: 72W Max.
• -40 to 75 (℃℃-40℉ to 167℉) operating temperature
range. Tested for functional operation @ -40 to 85 ℃℃
(-40℉ to 185℉).
• Supports DIN-Rail, Panel, or Rack Mounting
installation.
Assembly, Startup, and Dismantling
• Assembly: Place the switch on the DIN rail from above
using the slot. Push the front of the switch toward the
mounting surface until it audibly snaps into place.
• Startup: Connect the supply voltage to start up the
switch via the terminal block (or DC JACK).
• Dismantling: Pull out the lower edge and then remove
the switch from the DIN rail.
5
Hardened PoE Ethernet Switch
6
Hardened PoE Ethernet Switch
Preface
A member of the growing family of rugged switches, this
Hardened PoE Ethernet Switch addresses a need for a
smaller switch. This switch provides an affordable solution
for rugged and outdoor environment, transportation
road-side cabinet, industrial floor shop, multitenant
dwellings or Fiber To The Home (FTTH) applications.
Capable of operating at temperature extremes of -40°C to
+75°C, this is the switch of choice for harsh environments
constrained by space.
Port 1 to port 4 on this Switch supports IEEE802.3af Power
over Ethernet (PoE) Power Sourcing Equipment (PSE) and
can detect an IEEE802.3af compliant Powered Device
(PD). Using external 48VDC power inputs through
Terminal Block or Power Jack, data and power can be
transmitted to a Powered Device (PD) over the same
twisted-pair Ethernet cable through port 1 to port 4 on the
Switch.
This manual describes how to install and use the hardened
Ethernet Switch. This switch integrates full wire speed
switching technology. This switch brings the answer to
complicated hardened networking environments.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
• Features on the switch
• Illustrative LED functions
• Installation instructions
• Specifications
7
Hardened PoE Ethernet Switch
Table of Contents
QUICK START GUIDE 1
PHYSICAL DESCRIPTION 1
The Terminal Block and Power inputs 1
The 10/100Base-TX and 100Base-FX Connectors 2
The Port Status LEDs 3
FUNCTIONAL DESCRIPTION 5
ASSEMBLY, STARTUP, AND DISMANTLING 5
REFACE 7
P
T
ABLE OF CONTENTS 8
RODUCT OVERVIEW 9
P
HARDENED POE ETHERNET SWITCH 9
PACKAGE CONTENTS 9
PRODUCT HIGHLIGHTS 10
Basic Features 10
FRONT PANEL DISPLAY 11
PHYSICAL PORTS 12
I
NSTALLATION 13
SELECTING A SITE FOR THE SWITCH 13
DIN RAIL MOUNTING 14
CONNECTING TO POWER 15
Redundant DC Terminal Block Power Inputs 15
48VDC DC Jack 15
Alarms for Power and Port Link Failure 16
CONNECTING TO YOUR NETWORK 17
Cable Type & Length 17
Cabling 18
PECIFICATIONS 19
S
8
Hardened PoE Ethernet Switch
Product Overview
Hardened PoE Ethernet Switch
Package Contents
When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.
3 This Switch
3
3 External power adapter & Power Cord
User’s Manual
(Optional)
9
Hardened PoE Ethernet Switch
Product Highlights
Basic Features
• Meets NEMA TS1 & TS2 Environmental requirements
such as temperature, shock, and vibration for traffic
control equipment.
• Meets IEC61000-6-2 EMC Generic Standard Immunity
for industrial environment.
• Supports IEEE802.3af Power over Ethernet (PoE)
Power Sourcing Equipment (PSE).
• Support 802.3/802.3u/802.3X.
• Auto-negotiation: 10/100Mbps, Full/Half-duplex; Auto
MDI/MDIX.
• Support 1024 MAC addresses.
• Provides 1M bits memory buffer.
• Alarms for power and port link failure by relay output.
• Operating voltage and Max. current consumption: 1.5A
@ 48VDC. Power consumption: 72W Max.
• Power Supplies: Redundant 48VDC Terminal Block
power inputs and 48VDC DC JACK with 100-240VAC
external power supply.
• -40℃ to 75℃ (-40℉ to 167℉) operating temperature
range. Tested for functional operation @ -40℃ to 85℃
(-40℉ to 185℉).
• Supports DIN-Rail, Panel, or Rack Mounting
installation.
10
Hardened PoE Ethernet Switch
Front Panel Display
Status LEDs
LED State Indication
POWER
Power 1
Power 2
Power 3
(Green)
10/100TX or 100FX
Link/ACT
(Green)
Steady
Off
Steady A valid network connection established.
Flashing
Switch is properly connected to power and
turned on.
Switch is not connected to power and is
turned off.
Transmitting or receiving data.
ACT stands for ACTIVITY.
11
Hardened PoE Ethernet Switch
Physical Ports
This switch provides:
• Eight 10/100Base-TX ports
• Seven 10/100Base-TX ports + one 100Base-FX port
• Six 10/100Base-TX ports + two 100Base-FX ports
CONNECTIVITY
• RJ-45 connectors
• SC or ST connector on 100Base-FX fiber port.
12
Hardened PoE Ethernet Switch
Installation
This chapter gives step-by-step instructions about how to
install the switch:
Selecting a Site for the Switch
As with any electric device, you should place the switch
where it will not be subjected to extreme temperatures,
humidity, or electromagnetic interference. Specifically, the
site you select should meet the following requirements:
- The ambient temperature should be between -40 to 75
degrees Celsius.
- The relative humidity should be less than 95 percent,
non-condensing.
- Surrounding electrical devices should not exceed the
electromagnetic field (RFC) standards.
- Make sure that the switch receives adequate ventilation.
Do not block the ventilation holes on each side of the
switch
- The power outlet should be within 1.8 meters of the
switch.
13
Hardened PoE Ethernet Switch
DIN Rail Mounting
Fix the DIN rail attachment plate to the back panel of the
switch.
Installation: Place the switch on the DIN rail from above using
the slot. Push the front of the switch toward the mounting
surface until it audibly snaps into place.
Removal: Pull out the lower edge and then remove the switch
from the DIN rail.
14
Hardened PoE Ethernet Switch
Connecting to Power
Redundant DC Terminal Block Power Inputs and 48VDC
DC Jack:
Redundant DC Terminal Block Power Inputs
There are two pairs of power inputs can be used to power
up this device. You only need to have one power input
connected to run the switch.
Step 1: Connect the DC power cord to the plug-able terminal block on the
Step 2: Disconnect the power cord if you want to shut down the switch.
48VDC DC Jack
switch, and then plug it into a standard DC outlet.
Step 1: Connect the supplied AC to DC power adapter to the receptacle on
Step 2: Connect the power cord to the AC to DC power adapter and attach
the topside of the switch.
the plug into a standard AC outlet with the appropriate AC voltage.
15
Hardened PoE Ethernet Switch
Alarms for Power and Port Link Failure
Step 1: There are two pins on the terminal block are used for power failure
detection. It provides the normally closed output when the power
source is active. Use this as a dry contact application to send a
signal for power failure detection.
Power Input Assignment
Power3 48VDC DC Jack
＋
48VDC
Power2
Power1
－
＋
－
Power
Ground
48VDC
Power
Ground
Terminal
Block
Earth
Ground
Relay Alarm Assignment
*Relay warning signal disable for
following:
The relay contact closes if Power1
FAULT
and Power2 are both failed but
Power3 on.
The relay contact closes if Power3
is failed but Power1 and Power2
are both on.
Special note:
The relay output is normal open position when there is no pow er to the
switch. Please do not connect any power source to this terminal to
prevent the shortage to your power supply.
16
Hardened PoE Ethernet Switch
Connecting to Your Network
Cable Type & Length
It is necessary to follow the cable specifications below
when connecting the switch to your network. Use
appropriate cables that meet your speed and cabling
requirements.
Cable pecifications S
Speed
Connector Port Speed
Half/Full
Duplex
10Base-T RJ-45 10/20 Mbps 2-pair
100Base-TX RJ-45 100/200 Mbps 2-pair
100Base-FX SC, ST 100/200 Mbps MMF (50 or
100Base-FX SC, ST 100/200 Mbps SMF (9 or
Cable
UTP/STP
Cat. 3, 4, 5
UTP/STP
Cat. 5
62.5µm)
10µm)
Max.
Distance
100 m
100 m
2 km
20, 40, or 75
km
17
Hardened PoE Ethernet Switch
Cabling
Step 1: First, ensure the power of the switch and end devices is turned off.
<Note> Always ensure that the power is off before any installation.
Step 2: Prepare cable with corresponding connectors for each type of port
Step 3: Consult the previous section for cabling requirements based on
Step 4: Connect one end of the cable to the switch and the other end to a
Step 5: Once the connections between two end devices are made
in use.
connectors and speed.
desired device.
successfully, turn on the power and the switch is operational.
18
Hardened PoE Ethernet Switch
Specifications
Hardened PoE
Ethernet Switch
Applicable
Standards
Switching Method Store-and-Forward
Forwarding Rate
10Base-T:
100Base-TX/FX:
Performance 14,880pps for 10Mbps
Cable
10Base-T:
100Base-TX:
100Base-FX:
LED Indicators Per unit –
Dimensions 68mm (W) × 110mm (D) × 135mm (H)
Net Weight 1Kg (2.2lbs.)
Power Terminal Block: 48VDC
Operating Voltage &
Max. Current
Consumption
Power Consumption
Operating
Temperature
Storage Temperature
Humidity 5%-95% non-condensing
Safety UL508, EN60950-1, IEC60950-1
10/100Base-TX auto-negotiating ports with
RJ-45 connectors, 100Base-FX fiber ports
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX/FX
10 / 20Mbps half / full-duplex
100 / 200Mbps half / full-duplex
148,810pps for 100Mbps
4-pair UTP/STP Cat. 3, 4, 5
4-pair UTP/STP Cat. 5
Up to 100m (328ft)
MMF (50 or 62.5µm), SMF (9 or10µm)
Power status (Power 1, Power 2, Power 3)
Per port –
10/100TX or 100FX - Link/ACT (Green)
(2.68” (W) × 4.33” (D) × 5.31” (H))
DC Jack: 48VDC, External AC/DC required
1.5A @ 48VDC
72W Max.
-40°C to 75℃ (-40℉ to 167℉)
Tested for functional operation @
-40℃ to 85℃ (-40℉ to 185℉)
-40°C to 85°C (-40℉ to 185℉)
EMI
FCC Part 15, Class A
EN61000-6-3:
EN55022
EN61000-3-2
EN61000-3-3
EMS
19
Hardened PoE Ethernet Switch
EN61000-6-2:
EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated FRI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)
EN61000-4-11 (Voltage Dips Standards)
Environmental Test Compliance
IEC60068-2-6 Fc (Vibration Resistance)
IEC60068-2-27 Ea (Shock)
IEC60068-2-32 Ed (Free Fall)
NEMA TS1/2 Environmental requirements for traffic control equipment
20
Loading...