EtherWAN EX48041-10B, EX48041-90B, EX48041-80B, EX48041-20B, EX48041-A0B Quick Start Manual

Hardened Web-Smart High Power PoE Ethernet Switch

Quick Start Guide

This quick start guide describes how to install and use the Hardened
Web-Smart High Power PoE (Power over Ethernet) Ethernet Switch. This is
the switch of choice for harsh environments constrained by space.

Physical Description

The Port Status LEDs and Power Inputs

User’s Manual 1

Hardened Web-Smart High Power PoE Ethernet Switch

LED State Indication

Steady Power on.

Power1
Power2
Power3

Off Power off.

Steady Power redundant system failure occurred.

Fault

Off Power redundant system failure is not occurred.

10/100Base-TX, 100Base-FX/BX

Steady A valid network connection established.

Link/ACT

Flashing

Transmitting or receiving data.
ACT stands for ACTIVITY.

Steady Valid port connection at 100Mbps.

10/100

Off Valid port connection at 10Mbps.

Steady Powered Device (PD) is connected.

PoE

Off Powered Device (PD) is disconnected.

Power Input Assignment

Power3 55VDC DC Jack

＋

55VDC

Power2

－

Power Ground

＋

55VDC

Power1

－

Power Ground

Earth Ground

Terminal Block

Relay Output Rating 1A @ 24VDC

Relay Alarm Assignment

FAULT

*Warning signal disable for following:

The relay contact closes if Power1 and Power2 are
both failed but Power3 on.

The relay contact closes if Power3 is failed but
Power1 and Power2 are both on.

2 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

The 10/100Base-TX and 100Base-FX/BX Connectors

The 10/100Base-TX Connections

The following lists the pinouts of
10/100Base-TX ports.

Pin PoE Ports (Port 1-4) Non-PoE Port (Port 5)

1 Output Transmit Data + Output Transmit Data +

2 Output Transmit Data - Output Transmit Data -

3 Input Receive Data + Input Receive Data +

4 Positive (VCC+)

5 Positive (VCC+)

6 Input Receive Data - Input Receive Data -

7 Negative (VCC-)

8 Negative (VCC-)

The 100Base-FX Connections

The fiber port pinouts
The Tx (transmit) port of device I is connected to the Rx (receive) port of
device II, and the Rx (receive) port of device I to the Tx (transmit) port of
device II.

The WDM 100Base-BX Connections

The fiber port pinouts
Only one optical fiber is required to transmit and receive data.

Functional Description

z Meets NEMA TS2 Environmental requirements such as temperature,

shock, and vibration for traffic control equipment.

z Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity

for industrial environment.

z Manageable via Web browser interface.

z Port 1 – 4 support Power over Ethernet (PoE) Power Sourcing

Equipment (PSE).

z High Power PoE design up to 30W.

z Supports 802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps,

full/half-duplex. Auto MDI/MDIX.

z 100Base-FX: Multi mode/Single mode SC or ST type. 100Base-BX:

WDM Multi mode/Single mode SC type.

User’s Manual 3

Hardened Web-Smart High Power PoE Ethernet Switch

z Supports 1024 MAC addresses. Provides 512K bits memory buffer.

z Alarms for power and port link failure by relay output.

z Power Supply: Redundant 55VDC Terminal Block power inputs and

55VDC DC JACK with optional 100-240VAC external power supply.

z Operating voltage and Max. current consumption: 2.36A @ 55VDC.

Power consumption: 130W Max.

z -40℃ to 75℃ (-40℉ to 167℉) operating temperature range. Tested for

functional operation @ -40℃ to 85℃ (-40℉ to 185℉).

z Supports Wall and Desktop Mounting installation.

Web Configuration

z Login the switch:

Specify the default IP address (192.168.1.10) of the switch in the web

browser. A login window will be shown as below:

4 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

z Enter the factory default user name: admin.

Enter the factory default password: admin.

Then click on the “OK” button to log on to the switch.

User’s Manual 5

Hardened Web-Smart High Power PoE Ethernet Switch

6 User’s Manual

Preface

This manual describes how to install and use the Hardened
Web-Smart High Power PoE Ethernet Switch. This switch
introduced here is designed to deliver full scalability with
web-based management functions. Capable of operating at
temperature extremes of -40℃ to +75℃, this is the switch of

choice for harsh environments constrained by space.

Port 1 to port 4 on this switch supports Power over Ethernet
(PoE) Power Sourcing Equipment (PSE) and can detect a
Powered Device (PD). Using external 55VDC power inputs
through Terminal Block or Power Jack, data and power can
be transmitted to a Powered Device (PD) over the same
twisted-pair Ethernet cable through port 1 to port 4 on the
switch.

To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.

In this manual, you will find:

Features on the Hardened Web-Smart High Power PoE Ethernet Switch

z Illustrative LED functions
z Installation instructions
z Management Configuration
z Specifications

Hardened Web-Smart High Power PoE Ethernet Switch

User’s Manual 7

Table of Contents

Quick Start Guide 1

PHYSICAL DESCRIPTION 1

The Port Status LEDs and Power Inputs 1
The 10/100Base-TX and 100Base-FX/BX Connectors 3

FUNCTIONAL DESCRIPTION 3
WEB CONFIGURATION 4

Preface 6
Table of Contents 7
Product Overview 9

HARDENED WEB-SMART HIGH POWER POE ETHERNET SWITCH 9
PACKAGE CONTENTS 9
PRODUCT HIGHLIGHTS 10

Basic Features 10

FRONT PANEL DISPLAY 11
PHYSICAL PORTS 12
SWITCH MANAGEMENT 12

Web-based browser interface 12

Installation 13

SELECTING A SITE FOR THE SWITCH 13
CONNECTING TO POWER 13

Redundant DC Terminal Block Power Inputs 13
55VDC DC Jack 14
Alarms for Power and Port Link Failure 14

CONNECTING TO YOUR NETWORK 15

Cable Type & Length 15
Cabling 15

Switch Management 17

MANAGEMENT ACCESS OVERVIEW 17
WEB MANAGEMENT 18

Web-Based Browser Management 19

LOGGING ON TO THE SWITCH 19
UNDERSTANDING THE BROWSER INTERFACE 21
ADMINISTRATOR 23

Authentication Configuration 23
System IP Configuration 24
System Status 25
Load Default Setting 26
Firmware Update 27
Reset Device 28

PORT MANAGEMENT 29

Hardened Web-Smart High Power PoE Ethernet Switch

8 User’s Manual

Port Configuration 29
Bandwidth Control 30
Broadcast Storm Control 31
Max. Packet Length 32
Port Alarm Setting 33

VLAN SETTING 34

Multi to 1 Setting 34
Tag Based VLAN 35
Port Based VLAN 36

QOS SETTING 37

Class of Service Configuration 37
High Priority Queue Configuration 38
Customization Diffserv 39

POE 40

PoE System Settings 40
PoE Port Settings 41
PoE Scheduling 42

PORT SECURITY 44
CONFIGURATION BACKUP/RECOVERY 45
LOGOUT 46

Specifications 47

Hardened Web-Smart High Power PoE Ethernet Switch

Product Overview

Hardened Web-Smart High Power PoE Ethernet
Switch

Front and Back View

Package Contents

When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.

•

The Hardened Web-Smart High Power PoE Ethernet Switch

•

User’s Manual

User’s Manual 9

Hardened Web-Smart High Power PoE Ethernet Switch

10 User’s Manual

Product Highlights

Basic Features

z Meets NEMA TS2 Environmental requirements such as temperature,

shock, and vibration for traffic control equipment.

z Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity

for industrial environment.

z Manageable via Web browser interface.

z Port 1 – 4 support Power over Ethernet (PoE) Power Sourcing

Equipment (PSE).

z High Power PoE design up to 30W.

z Supports 802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps,

full/half-duplex. Auto MDI/MDIX.

z 100Base-FX: Multi mode/Single mode SC or ST type. 100Base-BX:

WDM Multi mode/Single mode SC type.

z Supports 1024 MAC addresses. Provides 512K bits memory buffer.

z Alarms for power and port link failure by relay output.

z Power Supply: Redundant 55VDC Terminal Block power inputs and

55VDC DC JACK with optional 100-240VAC external power supply.

z Operating voltage and Max. current consumption: 2.36A @ 55VDC.

Power consumption: 130W Max.

z -40℃ to 75℃ (-40℉ to 167℉) operating temperature range. Tested for

functional operation @ -40℃ to 85℃ (-40℉ to 185℉).

z Supports Wall and Desktop Mounting installation.

Hardened Web-Smart High Power PoE Ethernet Switch

Front Panel Display

z Power (Power1, Power2, Power3)
This LED comes on when the switch is properly connected to power and
turned on.

z Port Status LEDs
The LEDs are located on the front panel, displaying status for each
respective port. Please refer to the following table for more details.

LED State Indication

Steady Power on.

Power1
Power2
Power3

Off Power off.

Steady Power redundant system failure occurred.

Fault

Off Power redundant system failure is not occurred.

10/100Base-TX, 100Base-FX/BX

Steady A valid network connection established.

Link/ACT

Flashing

Transmitting or receiving data.
ACT stands for ACTIVITY.

Steady Valid port connection at 100Mbps.

10/100

Off Valid port connection at 10Mbps.

Steady Powered Device (PD) is connected.

PoE

Off Powered Device (PD) is disconnected.

User’s Manual 11

Hardened Web-Smart High Power PoE Ethernet Switch

12 User’s Manual

Physical Ports

The Hardened Web-Smart High Power PoE Ethernet Switch
provides:

CONNECTIVITY

z

RJ-45 connectors on TX ports

z ST or SC connector on 100Base-FX fiber port
z SC connector on 100Base-BX fiber port

MODE SELECTION

z

10Base-T full-duplex mode

z 10Base-T half-duplex mode

z 100Base-TX full-duplex mode

z 100Base-TX half-duplex mode
z 100Base-FX full-duplex mode
z Auto-negotiating mode

Switch Management

Web-based browser interface

The switch also boasts a point-and-click browser-based interface that
lets user access full switch configuration and functionality from a
Netscape or Internet Explorer browser.

Hardened Web-Smart High Power PoE Ethernet Switch

User’s Manual 13

Installation

This chapter gives step-by-step instructions about how to
install the switch:

Selecting a Site for the Switch

As with any electric device, you should place the switch
where it will not be subjected to extreme temperatures,
humidity, or electromagnetic interference. Specifically, the
site you select should meet the following requirements:

-The ambient temperature should be between -40℃ to 75℃ (-40℉ to
167℉).

-The relative humidity should be less than 95 percent, non-condensing.

-Surrounding electrical devices should not exceed the electromagnetic field
(RFC) standards.

-Make sure that the switch receives adequate ventilation. Do not block the
ventilation holes on each side of the switch.

Connecting to Power

Redundant DC Terminal Block Power Inputs or 55VDC DC
Jack:

Redundant DC Terminal Block Power Inputs

There are two pairs of power inputs for use with redundant
power sources. You only need to have one power input
connected to run the switch.

Step 1: Connect the DC power cord to the plug-able terminal block on the

switch, and then plug it into a standard DC outlet.

Step 2: Disconnect the power cord if you want to shut down the switch.

Hardened Web-Smart High Power PoE Ethernet Switch

55VDC DC Jack

Step 1: Connect the supplied AC to DC power adapter to the receptacle on

the back side of the switch.

Step 2: Connect the power cord to the AC to DC power adapter and attach

the plug into a standard AC outlet with the appropriate AC voltage.

Back View

Alarms for Power and Port Link Failure

Step 1: There are two pins on the terminal block used for power failure

detection. It provides the normally closed output when the power
source is active. Use this as a dry contact application to send a
signal for power failure detection.

Power Input Assignment

Power3 55VDC DC Jack

＋

55VDC

Power2

－

Power Ground

＋

55VDC

Power1

－

Power Ground

Earth Ground

Terminal Block

Relay Output Rating 1A @ 24VDC

Relay Alarm Assignment

FAULT

*Warning signal disable for following:

The relay contact closes if Power1 and Power2 are
both failed but Power3 on.

The relay contact closes if Power3 is failed but
Power1 and Power2 are both on.

Special note:
The relay output is normal open positio n when there is no pow er to the
switch. Please do not connect any power source to this terminal to
prevent shorting your power supply.

14 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

User’s Manual 15

Connecting to Your Network

Cable Type & Length

It is necessary to follow the cable specifications below when connecting
the switch to your network. Use appropriate cables that meet your speed
and cabling requirements.

Cable Specifications

Speed Connector

Port
Speed
Half/Full
Duplex

Cable Max.

Distance

10Base-T RJ-45 10/20 Mbps 2-pair

UTP/STP
Cat. 3, 4, 5

100 m

100Base-TX RJ-45 100/200

Mbps

2-pair
UTP/STP
Cat. 5

100 m

100Base-FX ST, SC 200 Mbps MMF (50 or

62.5μm)

2 km

100Base-FX ST, SC 200 Mbps SMF (9 or

10μm)

20 or 40 km

100Base-BX SC 200 Mbps MMF (50 or

62.5μm)

2 or 5 km

100Base-BX SC 200 Mbps SMF (9 or

10μm)

20 or 40 km

Cabling

Step 1: First, ensure the power of the switch and end devices are turned off.

<Note> Always ensure that the power is off before any installation.

Step 2: Prepare cable with corresponding connectors for each type of port

in use.

Step 3: Consult Cable Specifications Table on previous page for cabling

requirements based on connectors and speed.

Step 4: Connect one end of the cable to the switch and the other end to a

Hardened Web-Smart High Power PoE Ethernet Switch

16 User’s Manual

desired device.

Step 5: Once the connections between two end devices are made

successfully, turn on the power and the switch is operational.

Hardened Web-Smart High Power PoE Ethernet Switch

User’s Manual 17

Switch Management

This chapter explains the methods that you can use to
configure management access to the switch. It describes the
types of management applications and the communication
and management protocols that deliver data between your
management device (workstation or personal computer) and
the system. It also contains information about port connection
options.

This chapter covers the following topics:

• Management Access Overview

• Key Concepts

• Key Guidelines for Implementation

• Web Management Access

• Standards, Protocols, and Related Reading

Management Access Overview

The switch gives you the flexibility to access and manage the
switch using any or all of the following methods.

The web browser interface support is embedded in the switch
software and is available for immediate use.

Hardened Web-Smart High Power PoE Ethernet Switch

18 User’s Manual

Web Management

The switch provides a browser interface that lets you
configure and manage the switch remotely.

After you set up your IP address for the switch, you can
access the switch’s web interface applications directly in your
web browser by entering the IP address of the switch. You
can then use your web browser to list and manage switch
configuration parameters from one central location, just as if
you were directly connected to the switch’s console port.

Hardened Web-Smart High Power PoE Ethernet Switch

Web-Based Browser Management

The switch provides a web-based browser interface for
configuring and managing the switch. This interface allows
you to access the switch using a preferred web browser.

This chapter describes how to configure the switch using its
web-based browser interface.

Logging on to the switch

SWITCH IP ADDRESS

In your web browser, specify the IP address of the switch. Default IP address
is 192.168.1.10.

User’s Manual 19

Hardened Web-Smart High Power PoE Ethernet Switch

20 User’s Manual

USER NAME

Enter the factory default user name: admin.

PASSWORD

Enter the factory default password: admin.
Or enter a user-defined password if you followed the instructions later and
changed the factory default password.

Then click on the “OK” button to log on to the switch.

Hardened Web-Smart High Power PoE Ethernet Switch

Understanding the Browser Interface

The web browser interface provides groups of point-and-click
buttons at the left field of the screen for configuring and
managing the switch.

Administrator

Authentication Configuration, System IP Configuration, System Status, Load
Default Setting, Firmware Update, Reset Device

Port Management

Port Configuration, Bandwidth Control, Broadcast Storm Control, Max.
Packet Length, Port Alarm Setting

VLAN Setting

Multi to 1 Setting, Tag Based VLAN, Port Based VLAN

QoS Setting

Class of Service Configuration, High Priority Queue Configuration,
Customization Diffserv

User’s Manual 21

Hardened Web-Smart High Power PoE Ethernet Switch

22 User’s Manual

PoE

PoE System Settings, PoE Port Settings, PoE Scheduling

Port Security
Configuration Backup/Recovery
Logout

Hardened Web-Smart High Power PoE Ethernet Switch

Administrator

Authentication Configuration

1. Username: Click in “Username” text box and type in a new username.

2. Password: Click in “Password” text box and type in a new password.

3. Confirm: Click in “Confirm” text box. Type the same password in
“Password” text box again to verify it.

4. Update: Click “Update” button to update your settings.

<Note> Username & Password can only use “a-z”, “A-Z”, “0-9”, “_”, “＋”, “－”,

and “＝”.

User’s Manual 23

Hardened Web-Smart High Power PoE Ethernet Switch

System IP Configuration

1. IP Address: Click in “IP Address” text box and type a new address to
change the IP Address.

2. Subnet Mask: Click in “Subnet Mask” text box and type a new address
to change the Subnet Mask.

3. Gateway: Click in “Gateway” text box and type a new address to change
the Gateway.

4. IP Configure: Click and choose “Static” or “DHCP” to disable or enable
the Switch as DHCP client to be automatically supplied an IP address,
gateway address, and subnet mask from DHCP server.

5. Update: Click “Update” button to update your settings.

24 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

System Status

1. Comment: Click in “Comment” text box and type a new comment for this
Switch.

2. Idle Time Security: Click and choose “Idle Time Security” to enable or
disable protection security for managing the Switch after a period of idle
time.

3. Idle Time (1~30 Minutes): Click in “Idle Time” text box and type an idle
time. This is for protection security to manage the Switch after a period
of idle time.

4. Auto Logout (Default): Click and choose “Auto Logout” to automatically
log the user out after a period of idle time. And this is the default setting
for Idle Time Security.

5. Back to the last display: Click and choose “Back to the last display” to
back to the last displayed web screen before a period of idle time.

6. Update: Click “Update” button to update your settings.

<Note> Comment name can only use “a-z”, “A-Z”, “0-9”, “_”, “＋”, “－”, and

“＝”.

User’s Manual 25

Hardened Web-Smart High Power PoE Ethernet Switch

Load Default Setting

Load: Click “Load” button to restore the default setting of the Switch
excluding the IP Address, User Name, and Password.

26 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

Firmware Update

1. Password: Click in “Password” text box and type in the password.

2. ReConfirm: Click in “ReConfirm” text box. Type the same password in
“Password” text box again to verify it.

3. Update: Click “Update” button to continue the Firmware Update process.

User’s Manual 27

Hardened Web-Smart High Power PoE Ethernet Switch

Reset Device

Confirm: Click “Confirm” button to reboot the Switch.

28 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

Port Management

Port Configuration

1. Port No.: Click “Port No.” drop-down menu to choose port from “Port
No.” drop-down list.

2. Name: Click the “Name” check box. Then click in “Name” text box and
type a name for the port. Port name can only use “a-z”, “A-Z”, “0-9”, “_”,
“＋”, “－”, and “＝”.

3. Link Capability: Click “Link Capability” drop-down menu to choose
“Auto-Nego.(All Capabilities)”, “Forced 100M”, or “Forced 10M” and
change the line speed from the “Link Capability” drop-down list for the
port.

4. Duplex: Click “Duplex” drop-down menu to choose “Full” or “Half” from
the “Duplex” drop-down list to set Full Duplex mode or Half Duplex
mode for the port.

5. Port Tx/Rx Ability: Click “Port Tx/Rx Ability” drop-down menu to choose
“Disable” or “Enable” from the “Port Tx/Rx Ability” drop-down list to
disable or enable transmitting/receiving ability for the port.

6. Update: Click “Update” button to update your settings.

User’s Manual 29

Hardened Web-Smart High Power PoE Ethernet Switch

Bandwidth Control

1. Port No.: Click “Port No.” drop-down menu to choose port from “Port
No.” drop-down list.

2. TX Rate: Click “TX Rate” drop-down menu to choose the transmission
rate from the “TX Rate” drop-down list for the port.

3. RX Rate: Click “RX Rate” drop-down menu to choose the receiving rate
from the “RX Rate” drop-down list for the port.

4. Update: Click “Update” button to update your settings.

5. LoadDefault: Click “LoadDefault” button to load default settings.

<Note> If the link speed of selected port is lower than the rate set by user,

this system will use the link speed as user’s setting.

30 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

Broadcast Storm Control

1. Broadcast storm protection: Click the “Enable” check box to enable
broadcast storm protection for the Switch.

2. Update: Click “Update” button to update your settings.

User’s Manual 31

Hardened Web-Smart High Power PoE Ethernet Switch

Max. Packet Length

1. Packet Length (Bytes): Click and choose “1536 (default)” or “1552” to
set maximum 1536 (default Packet Length for the Switch) or 1552 Bytes
packet length for the Switch.

2. Update: Click “Update” button to update your settings.

32 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

Port Alarm Setting

1. Port: Click “Port” drop-down menu to choose port from the “Port”
drop-down list.

2. Trigger Enabled: Click “Trigger Enabled” drop-down menu to choose
“YES” or “NO” from the “Trigger Enabled” drop-down list to enable or
disable Trigger for the port.

3. Update: Click “Update” button to update your settings.

User’s Manual 33

Hardened Web-Smart High Power PoE Ethernet Switch

VLAN Setting

Multi to 1 Setting

1. Destination PortNo: Click “Destination PortNo” drop-down menu to
choose destination port from the “Destination PortNo” drop-down list.

2. Update: Click “Update” button to update your settings.

3. Restore: Click “Restore” button to restore the previous VLAN
configuration.

34 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

Tag Based VLAN

1. Tag Vlan Function: Click and choose “Enable” or “Disable” to enable or
disable Tag Based VLAN for the Switch.

2. Update: Click “Update” button to update your settings.

3. Tag Mode: Click and choose “Add Tag”, “Don’t Care”, or “Remove Tag”
for each port.

4. Update: Click “Update” button to update your settings.

5. LoadDefault: Click “LoadDefault” button to load default settings.

6. Port/PVID: Input PVID Index value (1~15) for each port.

7. Submit: Click “Submit” button to submit your settings.

8. LoadDefault: Click “LoadDefault” button to load default settings.

9. VLAN No: Click “VLAN No” drop-down menu to choose VLAN from the
“VLAN No” drop-down list.

10. VLAN Member: Click and choose ports to be added to VLAN.

11. Update: Click “Update” button to update your settings.

12. LoadDefault: Click “LoadDefault” button to load default settings.

<Note> Please don’t add VLAN tag on your control port.

User’s Manual 35

Hardened Web-Smart High Power PoE Ethernet Switch

Port Based VLAN

1. Port NO: Click “Port NO” drop-down menu to choose port from the “Port
NO” drop-down list.

2. VLAN Member: Click and choose ports to be added to port number.

3. Update: Click “Update” button to update your settings.

4. LoadDefault: Click “LoadDefault” button to load default settings.

36 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

QoS Setting

Class of Service Configuration

1. PortBase: Click the check box to enable PortBase mode high priority for
port.

2. VLAN Tag/IP/DS: Click the check box to enable VLAN Tag/IP/DS mode
high priority for port.

3. Update: Click “Update” button to update your settings.

<Note> When both PortBase mode and VLAN Tag/IP/DS mode are chosen

for port, packets of VLAN Tag/IP/DS mode have higher priority.

User’s Manual 37

Hardened Web-Smart High Power PoE Ethernet Switch

High Priority Queue Configuration

1. Mode: Click and choose Weight-Round-Robin Low weight to 1/4 or 1/8
for the Switch.

2. Update: Click “Update” button to update your settings.

38 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

Customization Diffserv

1. Index: Click “Index” drop-down menu to choose DiffServ Index from the
“Index” drop-down list.

2. Enable: Click “Enable” button to enable the Diffserv Index.

3. Disable: Click “Disable” button to disable the Diffserv Index.

<Note> Default enabled Index: 10, 18, 26, 34, 46, 48, and 56.

User’s Manual 39

Hardened Web-Smart High Power PoE Ethernet Switch

PoE

PoE System Settings

1. System power budget: Click in “System power budget” text box and type
a new system power budget.

2. Update: Click “Update” button to update your settings.

40 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

PoE Port Settings

1. Port: Click “Port” drop-down menu to choose port from the “Port”
drop-down list.

2. Enable Mode: Click “Enable Mode” drop-down menu to choose “Enable”,
“Disable”, or “Scheduling from the “Enable Mode” drop-down list to
enable, disable, or schedule Port 1 ~ Port 4 to discover Powered Device
(PD) connected to Port 1 ~ Port 4 of the Switch.

3. Power Limit by Classification: Click “Power Limit by Classification”
drop-down menu to choose “Enable” or “Disable” from the “Power Limit
by Classification” drop-down list to enable or disable Port 1 ~ Port 4 to
provide power to PD according to classification of maximum power
range used by PD.

4. Fix Power Limit(W): Click in “Fix Power Limit(W)” text box and type a
new fixed power limit for Port 1 ~ Port 4 to provide power to PD.

5. Power Priority: Click “Power Priority” drop-down menu to choose “High”,
“Middle”, or “Low” from the “Power priority” drop-down list to determine
power priority of Port 1 ~ Port 4.

6. Update: Click “Update” button to update your settings.

User’s Manual 41

Hardened Web-Smart High Power PoE Ethernet Switch

PoE Scheduling

Adjust RTC Time: Adjust system time for this Switch.

1. Year(2000-2037): Click in “Year” text box and specify year 2000 to 2037.

2. Month: Click in “Month” text box and specify 1 to 12.

3. Day: Click in “Day” text box and specify 1 to 31. Click drop-down menu
to choose “Mon” to “Sun” from the drop-down list.

4. Hour: Click in “Hour” text box and specify 0 to 23.

5. Minute: Click in “Minute” text box and specify 0 to 59.

6. Second: Click in “Second” text box and specify 0 to 59.

7. Update: Click “Update” button when you finished Adjust RTC Time.

1. Port: Click “Port” drop-down menu to choose port from the “Port”
drop-down list.

2. Day: Click “Day” drop-down menu to choose “Mon” to “Sun” from the
“Day” drop-down list.

42 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

User’s Manual 43

3. Time: Click the “Time” check box to enable PoE scheduling to this port
during these time periods.

4. Update: Click “Update” button to update your settings.

Status

1. Port: Click “Port” drop-down menu to choose port from the “Port”
drop-down list.

2. Update: Click “Update” button to update the PoE Schduling status of this
port.

Hardened Web-Smart High Power PoE Ethernet Switch

Port Security

1. Port: Click the “Enable” check box to enable Port Security for each port.
After power on reset, each port will record the source MAC address of
first received packet as a Security MAC address. A security port only
allows the packet which has the Security MAC address to active on.

2. Update: Click “Update” button to update your settings.

<Note> Please don’t enable port security on your control port.

44 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

Configuration Backup/Recovery

1. Backup(Switch→PC): Click “Download” button to download EEPROM
contents.

Recovery(PC→Switch)

1. Select the image file: Click “Browse” button to select the image file to be
recovered to the Switch.

2. Password: Click in “Password” text box and type in the password.

3. Update: Click “Update” button to confirm the recovery process.

User’s Manual 45

Hardened Web-Smart High Power PoE Ethernet Switch

Logout

1. Yes: Click “Yes” button to logout of the Switch.

2. No: Click “No” button to cancel the logout of the Switch.

46 User’s Manual

Hardened Web-Smart High Power PoE Ethernet Switch

User’s Manual 47

Specifications

Applicable Standards

IEEE802.3 10Base-T
IEEE802.3u 100Base-TX/FX

Switching Method Store-and-Forward
Forwarding Rate

10Base-T
100Base-TX
100Base-FX/BX

10Mbps half / full-duplex
100Mbps half / full-duplex
100Mbps full-duplex

Performance

14,880pps for 10Mbps
148,810pps for 100Mbps

Cable

10Base-T
100Base-TX
100Base-FX
100Base-BX

4-pair UTP/STP Cat. 3, 4, 5 Up to 100m (328ft)
4-pair UTP/STP Cat. 5 Up to 100m (328ft)
MMF (50 or 62.5μm), SMF (9 or 10μm)
MMF (50 or 62.5μm), SMF (9 or 10μm)

LED Indicators Per unit – Power status (Power1, Power2, Power3), Fault

Per port –
10/100TX: Link/ACT, 10/100, PoE
100FX/BX: Link/ACT, 10/100

Dimensions 200mm (W) x 134.3mm (D) x 35mm (H)

(7.87” (W) x 5.29” (D) x 1.38” (H))

Net Weight 0.8Kg (1.76lbs.)
Power Input

Terminal Block: 55VDC
DC Jack: 55VDC, External AC/DC required

Operating Voltage &
Max. Current

Consumption

2.36A @ 55VDC

Power Consumption

130W Max.

Operating
Temperature

-40℃ to 75℃ (-40℉ to 167℉)
Tested for functional operation @

-40℃ to 85℃ (-40℉ to 185℉)

Storage Temperature

-40°C to 85℃ (-40℉ to 185℉)

Humidity 5%-95% non-condensing
EMI FCC Part 15, Class A

EN61000-6-4: EN55022, EN61000-3-2, EN61000-3-3

EMS EN61000-6-2:

EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)

Environmental Test
Compliance

IEC60068-2-6 Fc (Vibration Resistance)
IEC60068-2-27 Ea (Shock)
IEC60068-2-32 Ed (Free Fall)

NEMA TS2 Environmental requirements for traffic control equipment