EtherWan EX45900 series Quick Start Guide

EX45900 series www.etherwan.com

Quick Start Guide

This quick start guide describes how to install and use the
Hardened PoE Gigabit Ethernet Switch. Capable of operating
at temperature extremes of -40°C to +75°C, this is the switch
of choice for harsh environments constrained by space.

Physical Description

The Port Status LEDs

1

EX45900 series www.etherwan.com

LED State Indication

Power (Green)

Fault (Red)

Gigabit Ports

Link/Act

PoE (Amber)

Steady Power on.

Off Power off.

Steady Relay starts alarm.

Off Relay non-alarm.

Steady

Blinking

Off No link.

Steady Powered Device is connected.

Off Powered Device is disconnected.

Blinking While Powered Device over 30W.

A valid network connection established.
10/100Mbps: Green, 1000Mbps: Amber.

Transmitting or receiving data.
Act stands for Activity.

The Terminal Block and Power Inputs

Power Input Assignment

＋

Power1

Power2

Relay Output Rating 1A @ 250VAC

24/48VDC

－

Power Ground

＋

24/48VDC

－

Power Ground

Earth Ground

Terminal Block

DC Terminal Block Power Input: The DC Terminal Block
power input can be used to power up this Switch.

2

EX45900 series www.etherwan.com

DIP Switch Settings

On Off DIP No.

1 Port 1 Alarm Enable. 1 Alarm Disable. Port

2 Port 2 Alarm Enable. Port 2 Alarm Disable.

3 Port 3 Alarm Enable. Port 3 Alarm Disable.

4 Port 4 Alarm Enable. Port 4 Alarm Disable.

5 Port 5 Alarm Enable. Port 5 Alarm Disable.

6

(Only for EX45915)
7 Broadcast Storm Enable. le.Broadcast Storm Disab

8 Jumbo Frame Enable. Jumbo Frame Disable.

he 1000Base-TX (PoE) and Gigabit Ethernet

T
Connectors

Port 6 Alarm Enable. Port 6 Alarm Disable.

1. The 1000Ba

se-TX Connections

The following lists the pinouts of 1000

3

Base-TX ports.

EX45900 series www.etherwan.com

Pin Signal Name Signal Definition

1

TP0＋ Transmit and Receive Data 0 ＋

2

TP0－ Transmit and Receive Data 0 －

3

TP1＋ Transmit and Receive Data 1 ＋

4

TP2＋ Transmit and Receive Data 2 ＋

5

TP2－ Transmit and Receive Data 2 －

6

TP1－ Transmit and Receive Data 1 －

7

TP3＋ Transmit and Receive Data 3 ＋

8

TP3－ Transmit and Receive Data 3 －

2. The SFP Socket Connections
The SFP socket for Gigabit fiber optic expansion.

3. The 1000Base-SX/LX Connections

The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx

(receive) port of device I to the Tx (transmit) port of device II.

4. The WDM 1000Base-BX Connections

The fiber port pinouts: Only one optical fiber is required to

transmit and receive data.

4

EX45900 series www.etherwan.com

Functional Description

 Complies with EN61000-6-2 & EN61000-6-4 EMC

Generic standard immunity for industrial environment.

 Supports 802.3/802.3u/802.3ab/802.3z/802.3x.

Auto-negotiation: 10/100/1000Mbps, Full/Half-duplex.
Auto MDI/MDIX.

 1000Base-SX/LX: Multi mode SC or ST type, Single

mode SC type. 1000Base-BX: WDM Single mode SC
type.

 Supports 8192 MAC addresses, 1M bits buffer memory.
 Supports IEEE802.3az Energy Efficient Ethernet

(EEE).

 High speed, non-blocking four traffic class QoS switch

fabric.

 Supports Jumbo frame up to 10K Bytes.
 Enable Broadcast Storm Protection by DIP Switch No.

7 to limit 15,000 packets per second.

 Port 1~4 support IEEE802.3at Power over Ethernet

(PoE) Power Sourcing Equipment (PSE) and provide
power up to 30W.

 Power consumption: 7W Max (Device only, without

PoE).

 PoE power budget: 120W.
 Power Supply: Redundant 24/48VDC Terminal Block

power inputs.

 Operating temperature ranges from -40°C to 75°C

(-40°F to 167°F).

 Slim design with DIN-Rail mount installation.

5

EX45900 series www.etherwan.com

Assembly, Startup, and Dismantling

 Assembly: Place the switch on the DIN rail from above

using the slot. Push the front of the switch toward the
mounting surface until it audibly snaps into place.

 Startup: Connect the supply voltage to start up the

switch via the terminal block.

 Dismantling: Pull out the lower edge and then remove

the switch from the DIN rail.

6

EX45900 series www.etherwan.com

Preface

This manual describes how to install and use the Hardened
PoE Gigabit Ethernet Switch. This switch introduced here is
capable of operating at temperature extremes of -40°C to
+75°C, this is the switch of choice for harsh environments
constrained by space.

Port 1 to port 4 on this switch supports IEEE802.3at Power
over Ethernet (PoE) Power Sourcing Equipment (PSE) and
can detect an IEEE802.3at compliant Powered Device (PD).
Using external 48VDC power inputs through Terminal Block,
data and power can be transmitted to a Powered Device (PD)
over the same twisted-pair Ethernet cable through port 1 to
port 4 on the switch.

To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.

In this manual, you will find:

 Features on the switch
 Illustrative LED functions
 Installation instructions
 Specifications

7

EX45900 series www.etherwan.com

Table of Contents

QUICK START GUIDE 1

PHYSICAL DESCRIPTION 1

The Port Status LEDs 1
The Terminal Block and Power Inputs 2
DIP Switch Settings 3
The 1000Base-TX (PoE) and Gigabit Ethernet Connectors 3

FUNCTIONAL DESCRIPTION 5
ASSEMBLY, STARTUP, AND DISMANTLING 6

REFACE 7

P
T

ABLE OF CONTENTS 8

RODUCT OVERVIEW 9

P

HARDENED POE GIGABIT ETHERNET SWITCH 9
PACKAGE CONTENTS 9
PRODUCT HIGHLIGHTS 10

Basic Features 10

FRONT PANEL DISPLAY 11
PHYSICAL PORTS 12

INSTALLATION 13

SELECTING A SITE FOR THE SWITCH 13
DIN RAIL MOUNTING 14
CONNECTING TO POWER 15

DC Terminal Block Power Inputs 15

CONNECTING TO YOUR NETWORK 16

Cable Type & Length 16
Cabling 17

SPECIFICATIONS 18

8

EX45900 series www.etherwan.com

Product Overview

Hardened PoE Gigabit Ethernet Switch

Package Contents

When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.

 This Switch
 User’s Manual

9

EX45900 series www.etherwan.com

Product Highlights

Basic Features

 Complies with EN61000-6-2 & EN61000-6-4 EMC

Generic standard immunity for industrial environment.

 Supports 802.3/802.3u/802.3ab/802.3z/802.3x.

Auto-negotiation: 10/100/1000Mbps, Full/Half-duplex.
Auto MDI/MDIX.

 1000Base-SX/LX: Multi mode SC or ST type, Single

mode SC type. 1000Base-BX: WDM Single mode SC
type.

 Supports 8192 MAC addresses, 1M bits buffer memory.
 Supports IEEE802.3az Energy Efficient Ethernet

(EEE).

 High speed, non-blocking four traffic class QoS switch

fabric.

 802.1Q VLAN Tag Based Priority, Class of Service.
 Output Queue Schedule Mode: Weighted Round Robin

(WRR) with 4 priority queues.

 The configurations of QoS are as below:

CoS Field Value Packet Count Priority

0 or 1 1 Lowest

2 or 3 2 Low

4 or 5 4 High

6 or 7 8 Highest

 Supports Jumbo frame up to 10K Bytes.
 Enable Broadcast Storm Protection by DIP Switch No.

7 to limit 15,000 packets per second.

 Port 1~4 support IEEE802.3at Power over Ethernet

(PoE) Power Sourcing Equipment (PSE) and provide
power up to 30W.

 Power consumption: 7W Max (Device only, without

PoE).

 PoE power budget: 120W.

10

EX45900 series www.etherwan.com

 Power Supply: Redundant 24/48VDC Terminal Block

power inputs.

 Operating temperature ranges from -40°C to 75°C

(-40°F to 167°F).

 Slim design with DIN-Rail mount installation.

Front Panel Display

　Power Status (PWR)

This LED comes on when the switch is properly connected to power and turned on.

　Port Status LEDs

The LEDs display status for each respective port.

11

EX45900 series www.etherwan.com

LED State Indication

Power (Green)

Fault (Red)

Gigabit Ports

Link/Act

PoE (Amber)

Steady Power on.

Off Power off.

Steady Relay starts alarm.

Off Relay non-alarm.

Steady

Blinking

Off No link.

Steady Powered Device is connected.

Off Powered Device is disconnected.

Blinking While Powered Device over 30W.

A valid network connection established.
10/100Mbps: Green, 1000Mbps: Amber.

Transmitting or receiving data.
Act stands for Activity.

Physical Ports

This switch provides:

 Five 10/100/1000Base-TX ports
 Five 10/100/1000Base-TX ports + one

1000Base-SX/LX/BX port

 Five 10/100/100Base-TX port + one Gigabit SFP slot

Connectivity

 RJ-45 connectors on TX ports
 ST or SC connector on 1000Base-SX/LX fiber port
 SC connector on 1000Base-BX fiber port
 Duplex LC connector on SFP 1000Base-SX/LX/BX

fiber transceiver

12

EX45900 series www.etherwan.com

Installation

This chapter gives step-by-step instructions about how to
install the switch:

Selecting a Site for the Switch

As with any electric device, you should place the switch
where it will not be subjected to extreme temperatures,
humidity, or electromagnetic interference. Specifically, the
site you select should meet the following requirements:

- The ambient temperature should be between -40 to 75
degrees Celsius.

- The relative humidity should be less than 95 percent,
non-condensing.

- Surrounding electrical devices should not exceed the
electromagnetic field (RFC) standards.

- Make sure that the switch receives adequate ventilation.

Do not block the ventilation holes on each side of the
switch

- The power outlet should be within 1.8 meters of the

switch.

13

EX45900 series www.etherwan.com

DIN Rail Mounting

Installation: Place the switch on the DIN rail from above using
the slot. Push the front of the switch toward the mounting
surface until it audibly snaps into place.

Removal: Pull out the lower edge and then remove the switch
from the DIN rail.

14

EX45900 series www.etherwan.com

Connecting to Power

DC Terminal Block Power Inputs

Step 1: Connect the DC power cord to the plug-able terminal block on the

Step 2: Disconnect the power cord if you want to shut down the switch.

switch, and then plug it into a standard DC outlet.

Power Input Assignment

＋

Power1

Power2

24/48VDC

－

Power Ground

＋

24/48VDC

－

Power Ground

Terminal Block

Relay Output Rating 1A @ 250VAC

Earth Ground

15

EX45900 series www.etherwan.com

Connecting to Your Network

Cable Type & Length

It is necessary to follow the cable specifications below
when connecting the switch to your network. Use
appropriate cables that meet your speed and cabling
requirements.

Cable Specifications

Speed Connector Port

Speed
Half/Full
Duplex

10Base-T RJ-45 10/20 Mbps 2-pair

100Base-TX RJ-45 100/200

Mbps

1000Base-T RJ-45 2000 Mbps 4-pair

1000Base-SX SC, ST 2000 Mbps MMF

1000Base-SX SC, ST 2000 Mbps MMF

1000Base-LX SC 2000 Mbps SMF (10μm) 10, 20, 50

1000Base-BX SC 2000 Mbps SMF (10μm) 20, 40 km

Cable Max.

Distance

UTP/STP
Cat. 3, 4, 5

2-pair
UTP/STP
Cat. 5

UTP/STP
Cat. 5

(62.5μm)

(50μm)

100 m

100 m

100 m

220 m
2 km

550 m

km

SFP

1000Base-SX Duplex LC 2000 Mbps MMF

1000Base-LX Duplex LC 2000 Mbps SMF (9μm) 10, 40, 60

1000Base-BX Duplex LC 2000 Mbps SMF (9μm) 70 km

16

(62.5μm)

550 m
2 km

km

EX45900 series www.etherwan.com

Cabling

Step 1: First, ensure the power of the switch and end devices are turned off.

<Note> Always ensure that the power is off before any installation.

Step 2: Prepare cable with corresponding connectors for each type of port

<Note> To connect two regular RJ-45 ports between switches or hubs, you need a

Step 3: Consult the previous section for cabling requirements based on

Step 4: Connect one end of the cable to the switch and the other end to a

Step 5: Once the connections between two end devices are made

in use.

straight or cross-over cable.

connectors and speed.

desired device.

successfully, turn on the power and the switch is operational.

17

EX45900 series www.etherwan.com

Specifications

Hardened PoE Gigabit
Ethernet Switch

Applicable Standards IEEE 802.3 10Base-T

Forwarding Rate
10Base-T:
100Base-TX:
1000Base-T/SX/LX:

Performance 148,80pps for 10Mbps

Cable
10Base-T:
100Base-TX:
1000Base-T:

1000Base-SX/LX:
LED Indicators Per unit – Power, Fault

Dimensions 30mm (W) × 100mm (D) × 149mm (H)

Net Weight 0.34Kg (0.75lb.)
Power Terminal Block: 24-48VDC
Power Consumption 7W Max (Device only, without PoE)
PoE Power Budget 120W
Operating

Temperature
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity 5%-95% non-condensing
EMI FCC Part 15 Class A, VCCI Class A

4 x 10/100/1000Base-TX PoE ports with
RJ-45 connectors plus 1-port
10/100/1000Base-TX or
1000Base-SX/LX/BX, or Gigabit SFP socket

IEEE 802.3u 100Base-TX
IEEE 802.3ab 1000Base-T
IEEE 802.3z 1000Base-SX/LX
IEEE 802.1x Full-duplex Flow Control
IEEE 802.1az Energy Efficient Ethernet
IEEE 802.1p Quality of Service (QoS)

10 / 20Mbps half / full-duplex
100 / 200Mbps half / full-duplex
2000Mbps full-duplex

148,810pps for 100Mbps
1,488,100pps for 1000Mbps

2-pair UTP/STP Cat. 3, 4, 5
2-pair UTP/STP Cat. 5
4-pair UTP/STP Cat. 5
Up to 100m (328ft)
MMF (50 or 62.5μm), SMF (9 or10μm)

Per port – Link/Act, PoE (For PoE ports)

(1.18” (W) × 4” (D) × 5.96” (H))

-40°C to 75°C (-40°F to 167°F)

EN61000-6-4
EN55022 Class A

18

EX45900 series www.etherwan.com

EMS EN61000-6-2:

Environmental Test
Compliance

EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)

IEC60068-2-6 Fc (Vibration)
IEC60068-2-27 Ea (Shock)
FED STD 101C Method 5007.1 (Free Fall w/
package)

19