EtherWAN EX42200 Quick Start Manual

EX42200 www.etherwan.com

Quick Start Guide

This quick start guide describes how to install and use the
Hardened PoE Ethernet Switch. Capable of operating at

temperature extremes of -40°C to +75°C, this is the switch of
choice for harsh environments constrained by space.

Physical Description

The Terminal Block and Power Inputs

Power Input Assignment

＋

18~57VDC

Power1

－

Power Ground

＋

18~57VDC

Power2

－

Power Ground

Earth Ground

Terminal Block

Relay Output Rating 1A @ 250VAC
Relay Alarm Assignment

Default is Power1 and Power2 both off.
Point 1 & 2 is close and Point 2 & 3 is open.

DC Terminal Block Power Inputs: There are two pairs of
power inputs can be used to power up this switch. Redundant
power supplies function is supported.

1

EX42200 www.etherwan.com

The 10/100Base-TX and 100Base-FX/BX Connectors

1. The 10/100Base-TX Connections

The following lists the pinouts of 10/100Base-TX ports.

Pin Signal Name Signal Definition

1

TD＋ Output Transmit Data ＋

2

TD－ Output Transmit Data －

3

RD＋ Input Receive Data ＋

4 PoE

Positive (VCC＋)

5 PoE

Positive (VCC＋)

6

RD－ Input Receive Data －

7 PoE

Negative (VCC－)

8 PoE

Negative (VCC－)

2. The 100Base-FX Connections

The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx

(receive) port of device I to the Tx (transmit) port of device II.

3. The WDM 100Base-BX Connections

The fiber port pinouts: Only one single optical fiber is required
to transmit and receive data.

2

EX42200 www.etherwan.com

The Port Status LEDs

3

EX42200 www.etherwan.com

4

LED State Indication

Steady Power on.

Power1

Power2

Off Power off.

Steady Power redundant system failure occurred.

Alarm

Off Power redundant system failure is not occurred.

10/100Base-TX

Steady A valid network connection established.

LINK/ACT

Flashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

Steady Valid port connection at 100Mbps.

10/100

Off Valid port connection at 10Mbps.

Steady Powered device (PD) is connected.

PoE

Off Powered device (PD) is disconnected.

100Base-FX/BX

Steady A valid network connection established.

LINK/ACT

Flashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

Steady Valid port connection at 100Mbps.

100

Off No valid port connection at 10Mbps.

EX42200 www.etherwan.com

5

Functional Description

 Meets EN61000-6-2 & EN61000-6-4 EMC Generic

Standard Immunity for industrial environment.

 Supports IEEE802.3at Power over Ethernet (PoE)

Power Sourcing Equipment (PSE).

 Port 1 to 4 support PoE function, IEEE802.3at Power

over Ethernet (PoE) and 10/100Base-TX.

 Up to 30W per PoE port, 55VDC, 600mA Max.
 Supports IEEE802.3/802.3u/802.3x. 10/100Mbps,

Full/Half-duplex, Auto-Negotiation, Auto MDI/MDIX.

 100Base-FX: Multi/Single mode SC or ST type.

100Base-BX: WDM Multi/Single mode SC type.

 Supports 2048 MAC addresses. Provides 448K bits

buffer memory.

 Alarms for power failure by relay output. Fully supports

normal open and normal close.

 Redundant dual 18 to 57VDC Terminal Block power

inputs.

 Device power consumption: 14W Max. (without PoE).

PoE power budget: 120W Max.

 Operating temperature ranges from -40℃ to 75℃

(-40℉ to 167℉), tested for functional operation @ -40
℃ to 85℃ (-40℉ to 185℉).

 Supports DIN-Rail installation.

Assembly, Startup, and Dismantling

 Assembly: Place the switch on the DIN rail from above

using the slot. Push the front of the switch toward the
mounting surface until it audibly snaps into place.

 Startup: Connect the supply voltage to start up the

switch via the terminal block.

 Dismantling: Pull out the lower edge and then remove

the switch from the DIN rail.

EX42200 www.etherwan.com

6

EX42200 www.etherwan.com

7

Preface

A member of the growing family of rugged switches, this
Hardened PoE Ethernet Switch addresses a need for a
smaller switch. This switch provides an affordable solution for
rugged and outdoor environment, transportation road-side
cabinet, industrial floor shop, multitenant dwellings or Fiber To
The Home (FTTH) applications. Capable of operating at

temperature extremes of -40°C to +75°C, this is the switch of
choice for harsh environments constrained by space.

Port 1 to port 4 on this Switch supports IEEE802.3at Power
over Ethernet (PoE) Power Sourcing Equipment (PSE) and
can detect an IEEE802.3at compliant Powered Device (PD).
Using external 18~57VDC power inputs through Terminal
Block, data and power can be transmitted to a Powered
Device (PD) over the same twisted-pair Ethernet cable
through port 1 to port 4 on the Switch.

This manual describes how to install and use the Hardened
PoE Ethernet Switch. This switch integrates full wire speed
switching technology. This switch brings the answer to
complicated Industrial networking environments.

To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.

In this manual, you will find:

 Features on the switch
 Illustrative LED functions
 Installation instructions
 Specifications

EX42200 www.etherwan.com

8

Table of Contents

QUICK START GUIDE 1

PHYSICAL DESCRIPTION 1

The Terminal Block and Power Inputs 1
The 10/100Base-TX and 100Base-FX/BX Connectors 2
The Port Status LEDs 3

FUNCTIONAL DESCRIPTION 5
ASSEMBLY, STARTUP, AND DISMANTLING 5

P

REFACE 7

T

ABLE OF CONTENTS 8

P

RODUCT OVERVIEW 9

HARDENED POE ETHERNET SWITCH 9
PACKAGE CONTENTS 9
PRODUCT HIGHLIGHTS 10

Basic Features 10

FRONT PANEL DISPLAY 11
PHYSICAL PORTS 13

INSTALLATION 14

SELECTING A SITE FOR THE SWITCH 14
DIN RAIL MOUNTING 15
CONNECTING TO POWER 16

Redundant DC Terminal Block Power Inputs 16
Alarms for Power and Port Link Failure 17

CONNECTING TO YOUR NETWORK 18

Cable Type & Length 18
Cabling 19

SPECIFICATIONS 20

EX42200 www.etherwan.com

Product Overview

Hardened PoE Ethernet Switch

Package Contents

When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.

 This Switch



User’s Manual

9

EX42200 www.etherwan.com

10

Product Highlights

Basic Features

 Meets EN61000-6-2 & EN61000-6-4 EMC Generic

Standard Immunity for industrial environment.

 Supports IEEE802.3at Power over Ethernet (PoE)

Power Sourcing Equipment (PSE).

 Port 1 to 4 support PoE function, IEEE802.3at Power

over Ethernet (PoE) and 10/100Base-TX.

 Up to 30W per PoE port, 55VDC, 600mA Max.
 Supports IEEE802.3/802.3u/802.3x. 10/100Mbps,

Full/Half-duplex, Auto-Negotiation, Auto MDI/MDIX.

 100Base-FX: Multi/Single mode SC or ST type.

100Base-BX: WDM Multi/Single mode SC type.

 Supports 2048 MAC addresses. Provides 448K bits

buffer memory.

 Alarms for power failure by relay output. Fully supports

normal open and normal close.

 Redundant dual 18 to 57VDC Terminal Block power

inputs.

 Device power consumption: 14W Max. (without PoE).

PoE power budget: 120W Max.

 Operating temperature ranges from -40℃ to 75℃

(-40℉ to 167℉), tested for functional operation @ -40
℃ to 85℃ (-40℉ to 185℉).

 Supports DIN-Rail installation.

EX42200 www.etherwan.com

Front Panel Display

11

EX42200 www.etherwan.com

12

Status LEDs

LED State Indication

Steady Power on.

Power1

Power2

Off Power off.

Steady Power redundant system failure occurred.

Alarm

Off Power redundant system failure is not occurred.

10/100Base-TX

Steady A valid network connection established.

LINK/ACT

Flashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

Steady Valid port connection at 100Mbps.

10/100

Off Valid port connection at 10Mbps.

Steady Powered device (PD) is connected.

PoE

Off Powered device (PD) is disconnected.

100Base-FX/BX

Steady A valid network connection established.

LINK/ACT

Flashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

Steady Valid port connection at 100Mbps.

100

Off No valid port connection at 10Mbps.

EX42200 www.etherwan.com

13

Physical Ports

This switch provides:

 Five 10/100Base-TX ports
 Four 10/100Base-TX ports + one 100Base-FX/BX port

CONNECTIVITY

 RJ-45 connector on TX ports
 SC or ST connector on 100Base-FX fiber port
 SC connector on 100Base-BX fiber port

EX42200 www.etherwan.com

14

Installation

This chapter gives step-by-step instructions about how to
install the switch:

Selecting a Site for the Switch

As with any electric device, you should place the switch
where it will not be subjected to extreme temperatures,
humidity, or electromagnetic interference. Specifically, the site
you select should meet the following requirements:

 The ambient temperature should be between -40 to 75

degrees Celsius.

 The relative humidity should be less than 95 percent,

non-condensing.

 Surrounding electrical devices should not exceed the

electromagnetic field (RFC) standards.

 Make sure that the switch receives adequate ventilation.

Do not block the ventilation holes on each side of the
switch

 The power outlet should be within 1.8 meters of the

switch.

EX42200 www.etherwan.com

DIN Rail Mounting

Fix the DIN rail attachment plate to the back panel of the
switch.

Installation: Place the switch on the DIN rail from above using
the slot. Push the front of the switch toward the mounting
surface until it audibly snaps into place.

Removal: Pull out the lower edge and then remove the switch
from the DIN rail.

15

EX42200 www.etherwan.com

Connecting to Power

Redundant DC Terminal Block Power Inputs

There are two pairs of power inputs can be used to power up
this device. You only need to have one power input connected
to run the switch.

Step 1: Connect the DC power cord to the plug-able terminal block on the

switch, and then plug it into a standard DC outlet.

Step 2: Disconnect the power cord if you want to shut down the switch.

16

EX42200 www.etherwan.com

Alarms for Power and Port Link Failure

Step 1: There are three pins on the terminal block are used for power failure

detection. It fully supports normal open and normal close. Use this
as a dry contact application to send a signal for power failure
detection.

Power Input Assignment

＋

18~57VDC

Power1

－

Power Ground

＋

18~57VDC

Power2

－

Power Ground

Earth Ground

Terminal Block

Relay Output Rating 1A @ 250VAC
Relay Alarm Assignment

Default is Power1 and Power2 both off.
Point 1 & 2 is close and Point 2 & 3 is open.

Relay Contact Power1 Power2 Point 1 & 2 Point 2 & 3

Start Alarm Off Off Close Open

Start Alarm Off On Close Open

Start Alarm On Off Close Open

Non-Alarm On On Open Close

17

EX42200 www.etherwan.com

18

Connecting to Your Network

Cable Type & Length

It is necessary to follow the cable specifications below when
connecting the switch to your network. Use appropriate
cables that meet your speed and cabling requirements.

Cable S ecifications p

Speed

Connector Port Speed

Half/Full
Duplex

Cable

Max.
Distance

10Base-T RJ-45 10/20 Mbps 2-pair

UTP/STP
Cat. 3, 4, 5

100 m

100Base-TX RJ-45 100/200 Mbps 2-pair

UTP/STP
Cat. 5

100 m

100Base-FX SC, ST 200 Mbps MMF (50 or

62.5μm)

2 km

100Base-FX SC, ST 200 Mbps SMF (9 or

10μm)

20 or 40 km

100Base-BX SC 200 Mbps MMF (50 or

62.5μm)

2 or 5 km

100Base-BX SC 200 Mbps SMF (9 or

10μm)

20 or 40 km

EX42200 www.etherwan.com

19

Cabling

Step 1: First, ensure the power of the switch and end devices are turned off.

<Note> Always ensure that the power is off before any installation.

Step 2: Prepare cable with corresponding connectors for each type of port

in use.

Step 3: Consult the previous section for cabling requirements based on

connectors and speed.

Step 4: Connect one end of the cable to the switch and the other end to a

desired device.

Step 5: Once the connections between two end devices are made

successfully, turn on the power and the switch is operational.

EX42200 www.etherwan.com

20

Specifications

Hardened PoE
Ethernet Switch

10/100Base-TX auto-negotiating ports with
RJ-45 connectors, 100Base-FX/BX fiber port

Applicable
Standards

IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX/FX

Switching Method Store-and-Forward
Forwarding Rate

10Base-T:
100Base-TX:
100Base-FX/BX:

10 / 20Mbps half / full-duplex
100 / 200Mbps half / full-duplex
200Mbps full-duplex

Performance 14,880pps for 10Mbps

148,810pps for 100Mbps

Cable

10Base-T:
100Base-TX:

100Base-FX/BX:

4-pair UTP/STP Cat. 3, 4, 5
4-pair UTP/STP Cat. 5
Up to 100m (328ft.)
MMF (50 or 62.5μm), SMF (9 or 10μm)

LED Indicators Per unit –

Power status (Power 1, Power 2), Alarm

Per port –

10/100TX - LINK/ACT, 100, PoE
100FX/BX - LINK/ACT, 100

Dimensions 61mm (W) × 73mm (D) × 110mm (H)

(2.4” (W) x 2.87” (D) x 4.33”(H))

Net Weight 0.6Kg (1.32lbs.)
Power Terminal Block: 18~57VDC
Power Consumption

Device: 14W Max. (without PoE)

PoE power budget: 120W Max.

Operating
Temperature

-40℃ to 75℃ (-40℉ to 167℉)
Tested @ -40℃ to 85℃ (-40℉ to 185℉)

Storage Tem per ature

-40℃ to 85℃ (-40℉ to 185℉)

Humidity 5%-95% non-condensing

EMI

FCC Part 15, Class A
CE, VCCI Class A
EN61000-6-4

EN55022
EN61000-3-2
EN61000-3-3

EMS

EN61000-6-2

EN61000-4-2 (ESD Standard)

EX42200 www.etherwan.com

21

EN61000-4-3 (Radiated FRI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)

Environmental Test Complia nc e

IEC60068-2-6 Fc (Vibration Resistance)
IEC60068-2-27 Ea (Shock)
FED STD 101C Method 5007.1 (Free Fall with package)