EtherWan EX32905 series, EX32914 series Quick Start Guide

EX32905/EX32914 series www.etherwan.com

Quick Start Guide

This quick start guide describes how to install and use the
Industrial Gigabit Ethernet Switch. Capable of operating at

temperature extremes of -10°C to 60°C, this is the Switch of
choice for harsh environments constrained by space.

Physical Description

The Port Status LEDs

1

EX32905/EX32914 series www.etherwan.com

LED State Indication
PWR

10/100

1000

Steady Device is powered up.
Off Device is powered off.

Steady

Flashing Transmitting or receiving data.
Steady A valid network connection established at 1000Mbps.
Off The port is transferring at 10Mbps If this LED is dark.

A valid network connection established at 10 or
100Mbps.

The Terminal Block and Power Input

The Terminal Block
PWR Power Input
GND Power Ground

Earth Ground

DC Terminal Block Power Input: The DC Terminal Block
power input can be used to power up this Switch / Media
Converter.

CAUTION: This equipment is designed to permit the

connection of the earthed conductor of the DC supply circuit
to the earthing conductor at the equipment.
If this connection is made, all of the following conditions must
be met:

 This equipment shall be connected to directly to the DC supply

system earthing electrode conductor or to a bonding jumper from
an earthing terminal bar or bus to which the DC supply system
earthing electrode conductor is connected.

2

EX32905/EX32914 series www.etherwan.com

 This equipment shall be located in the same immediate area

(such as, adjacent cabinets) as any other equipment that has a
connection between the earthed conductor of the same DC
supply circuit and the earthing conductor, and also the point of
earthing of the DC system. The DC system shall not be earthed
elsewhere.

 The DC supply source is to be located within the same premises

as the equipment.

 Switching or disconnecting devices shall not be in the earthed

circuit conductor between the DC source and the point of
connection of the earthing electrode conductor.

The 10/100/1000Base-TX and 1000Base-SX/LX/BX Connectors

1. The 10/100/1000Base-TX Connections

The following lists the pinouts of 10/100/1000Base-TX ports.

Pin Regular Ports Uplink port

1

TP0＋ Transmit and Receive Data 0 ＋

2

TP0－ Transmit and Receive Data 0 －

3

TP1＋ Transmit and Receive Data 1 ＋

4

TP2＋ Transmit and Receive Data 2 ＋

5

TP2－ Transmit and Receive Data 2 －

6

TP1－ Transmit and Receive Data 1 －

7

TP3＋ Transmit and Receive Data 3 ＋

8

TP3－ Transmit and Receive Data 3 －

3

EX32905/EX32914 series www.etherwan.com

2. The 1000Base-SX/LX Connections

The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx

(receive) port of device I to the Tx (transmit) port of device II.

3. The WDM 1000Base-BX Connections

The fiber port pinouts: Only one Single mode or Multi mode

optical fiber is required to transmit and receive data.

Functional Description

 Complies with EN61000-6-2 & EN61000-6-4 EMC Generic

standard immunity for industrial environment.

 Supports 802.3/802.3u/802.3ab/802.3z/802.3x.

Auto-negotiation: 10/100/1000Mbps, Full/Half-duplex. Auto
MDI/MDIX.

 1000Base-SX/LX: Multi mode SC or ST type, Single mode SC

or ST type. 1000Base-BX: WDM Multi mode or Single mode
SC type.

 Supports 8192 MAC addresses, 1M bits buffer memory.
 Jumbo frame supported up to 10K bytes.
 IEEE802.3az Energy Efficient Ethernet (EEE) supported.
 Quality of Service (QoS) supported based on layer 2

priorities.

 Power consumption: 6.5W Max. 0.25A @ 24VDC.
 Power supply: DC Terminal Block power input, 12-48VDC.

4

EX32905/EX32914 series www.etherwan.com

 -10°C to 60°C (14°F to 140°F) operating temperature range.

Tested for functional operation @ -20°C to 70°C (-4°F to
158°F).

 Metal compact DIN-Rail industrial case design.

5

EX32905/EX32914 series www.etherwan.com

Assembly, Startup, and Dismantling

 Assembly: Place the device on the DIN-Rail from above using

the slot. Push the front of the device toward the mounting
surface until it audibly snaps into place.

 Startup: Connect the supply voltage to start up the device via

the terminal block.

 Dismantling: Pull out the lower edge and then remove the

device from the DIN-Rail.

6

EX32905/EX32914 series www.etherwan.com

Preface

A member of the growing family of rugged switches, this
switch addresses a need for a smaller switch. This switch
provides an affordable solution for rugged and outdoor
environment, transportation road-side cabinet, industrial floor
shop, multitenant dwellings or Fiber To The Home (FTTH)
applications. Capable of operating at temperature extremes of

-10°C to 60°C, this is the switch of choice for harsh
environments constrained by space.

Plug-and-Play Solution:
The switch is a plug-and-play Gigabit Ethernet Switch in
compact size. It doesn't have any complicated software to set
up.

This manual describes how to install and use the industrial
compact Gigabit Ethernet Switch. This switch integrates full
wire speed switching technology. This switch brings the
answer to complicated hardened networking environments.

To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.

In this manual, you will find:

 Features on the switch
 Illustrative LED functions
 Installation instructions
 Specifications

7

EX32905/EX32914 series www.etherwan.com

Table of Contents

QUICK START GUIDE 1

PHYSICAL DESCRIPTION 1

The Port Status LEDs 1
The Terminal Block and Power Input 2
The 10/100/1000Base-TX and 1000Base-SX/LX/BX Connectors 3

FUNCTIONAL DESCRIPTION 4
ASSEMBLY, STARTUP, AND DISMANTLING 6

REFACE 7

P
T

ABLE OF CONTENTS 8
RODUCT OVERVIEW 9

P

INDUSTRIAL GIGABIT ETHERNET SWITCH 9
PACKAGE CONTENTS 9
PRODUCT HIGHLIGHTS 10

Basic Features 10

FRONT PANEL DISPLAY 11
PHYSICAL PORTS 12

INSTALLATION 13

SELECTING A SITE FOR THE SWITCH 13
DIN RAIL MOUNTING 14
CONNECTING TO POWER 15

DC Terminal Block Power Inputs 15

CONNECTING TO YOUR NETWORK 17

Cable Type & Length 17
Cabling 18

SPECIFICATIONS 19

8

EX32905/EX32914 series www.etherwan.com

Product Overview

Industrial Gigabit Ethernet Switch

Package Contents

When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.

 This Switch
 User’s Manual

9

EX32905/EX32914 series www.etherwan.com

Product Highlights

Basic Features

 Complies with EN61000-6-2 & EN61000-6-4 EMC Generic

standard immunity for industrial environment.

 Supports 802.3/802.3u/802.3ab/802.3z/802.3x.

Auto-negotiation: 10/100/1000Mbps, Full/Half-duplex. Auto
MDI/MDIX.

 1000Base-SX/LX: Multi mode SC or ST type, Single mode SC

or ST type. 1000Base-BX: WDM Multi mode or Single mode
SC type.

 Supports 8192 MAC addresses, 1M bits buffer memory.
 Jumbo frame supported up to 10K bytes.
 IEEE802.3az Energy Efficient Ethernet (EEE) supported.
 Quality of Service (QoS) supported based on layer 2

priorities.

 802.1Q VLAN Tag Based Priority, Class of Service.
 Output Queue Schedule Mode: Weighted Round Robin

(WRR) with 4 priority queues.

 The configurations of QoS are as below:

CoS Field Value Packet Count Priority

0 or 1 1 Lowest

2 or 3 2 Low

4 or 5 4 High

6 or 7 8 Highest

 Power consumption: 6.5W Max. 0.25A @ 24VDC.
 Power supply: DC Terminal Block power input, 12-48VDC.
 -10°C to 60°C (14°F to 140°F) operating temperature range.

Tested for functional operation @ -20°C to 70°C (-4°F to
158°F).

 Metal compact DIN-Rail industrial case design.

10

EX32905/EX32914 series www.etherwan.com

Front Panel Display

　Power Status (PWR)

This LED comes on when the switch is properly connected to
power and turned on.

　Port Status LEDs

The LEDs display status for each respective port.

LED State Indication
PWR

10/100

1000

Steady Device is powered up.
Off Device is powered off.

Steady

Flashing Transmitting or receiving data.
Steady A valid network connection established at 1000Mbps.
Off The port is transferring at 10Mbps If this LED is dark.

A valid network connection established at 10 or
100Mbps.

11

EX32905/EX32914 series www.etherwan.com

Physical Ports

This switch provides:

 Five 10/100/1000Base-TX ports
 Four 10/100/1000Base-TX ports + one 1000Base-SX/LX/BX

port

Connectivity:

 RJ-45 connectors
 SC or ST connector on 1000Base-SX/LX fiber port
 SC connector on 1000Base-BX fiber port

12

EX32905/EX32914 series www.etherwan.com

Installation

This chapter gives step-by-step instructions about how to
install the switch:

Selecting a Site for the Switch

As with any electric device, you should place the switch
where it will not be subjected to extreme temperatures,
humidity, or electromagnetic interference. Specifically, the site
you select should meet the following requirements:

 The ambient temperature should be between -10 to 60

degrees Celsius.

 The relative humidity should be less than 95 percent,

non-condensing.

 Surrounding electrical devices should not exceed the

electromagnetic field (RFC) standards.

 Make sure that the switch receives adequate ventilation. Do

not block the ventilation holes on each side of the switch

 The power outlet should be within 1.8 meters of the switch.

13

EX32905/EX32914 series www.etherwan.com

DIN Rail Mounting

Installation: Place the switch on the DIN rail from above using
the slot. Push the front of the switch toward the mounting
surface until it audibly snaps into place.

Removal: Pull out the lower edge and then remove the switch
from the DIN rail.

14

EX32905/EX32914 series www.etherwan.com

Connecting to Power

DC Terminal Block Power Inputs

Step 1: Connect the DC power cord to the plug-able terminal block on the

Step 2: Disconnect the power cord if you want to shut down the switch.

switch, and then plug it into a standard DC outlet.

The Terminal Block
PWR Power Input
GND Power Ground

Earth Ground

CAUTION: This equipment is designed to permit the
connection of the earthed conductor of the DC supply circuit
to the earthing conductor at the equipment.

If this connection is made, all of the following conditions must
be met:

 This equipment shall be connected to directly to the DC

supply system earthing electrode conductor or to a bonding
jumper from an earthing terminal bar or bus to which the DC
supply system earthing electrode conductor is connected.

 This equipment shall be located in the same immediate area

(such as, adjacent cabinets) as any other equipment that has
a connection between the earthed conductor of the same DC
supply circuit and the earthing conductor, and also the point of

15

EX32905/EX32914 series www.etherwan.com

earthing of the DC system. The DC system shall not be
earthed elsewhere.

 The DC supply source is to be located within the same

premises as the equipment.

 Switching or disconnecting devices shall not be in the earthed

circuit conductor between the DC source and the point of
connection of the earthing electrode conductor.

16

EX32905/EX32914 series www.etherwan.com

Connecting to Your Network

Cable Type & Length

It is necessary to follow the cable specifications below when
connecting the switch to your network. Use appropriate
cables that meet your speed and cabling requirements.

Cable Specifications

Speed Connector Port Speed

Half/Full Duplex

10Base-T RJ-45 10/20 Mbps 2-pair UTP/STP

100Base-TX RJ-45 100/200 Mbps 2-pair UTP/STP

1000Base-T RJ-45 2000 Mbps 4-pair UTP/STP

1000Base-SX SC, ST 2000 Mbps MMF (50 or

1000Base-SX SC 2000 Mbps MMF (50 or

1000Base-LX SC 2000 Mbps SMF (9 or

1000Base-BX SC 2000 Mbps SMF (9 or

Cable Max.

Distance

100 m

Cat. 3, 4, 5

100 m

Cat. 5

100 m

Cat. 5

550 m

62.5μm)

2 km

62.5μm)

10 or 20 km

10μm)

20 km

10μm)

17

EX32905/EX32914 series www.etherwan.com

Cabling

Step 1: First, ensure the power of the switch and end devices are turned off.

<Note> Always ensure that the power is off before any installation.

Step 2: Prepare cable with corresponding connectors for each type of port

<Note> To connect two regular RJ-45 ports between switches or hubs, you need a

Step 3: Consult the previous section for cabling requirements based on

Step 4: Connect one end of the cable to the switch and the other end to a

Step 5: Once the connections between two end devices are made

in use.

straight or cross-over cable.

connectors and speed.

desired device.

successfully, turn on the power and the switch is operational.

18

EX32905/EX32914 series www.etherwan.com

Specifications

Industrial Compact
Switch

Applicable Standards IEEE 802.3 10Base-T

Forwarding Rate
10Base-T:
100Base-TX:
1000Base-T/SX/LX/BX:

Performance 148,80pps for 10Mbps

Cable
10Base-T:
100Base-TX:
1000Base-T:

100Base-SX/LX/BX:
LED Indicators Per unit – Power status (PWR)

Dimensions 30mm (W) × 82mm (D) × 114mm (H)

Net Weight 0.34Kg (0.75lb.)
Power Terminal Block: 12-48VDC
Operating Voltage &

Max. Current
Consumption

Power Consumption 6.5W Max.
Operating Temperature -10°C to 60°C (14°F to 140°F)

Storage Temperature -25°C to 85°C (-13°F to 185°F)
Humidity 5%-95% non-condensing
EMI FCC Part 15 Class A, VCCI

10/100/1000Base-TX auto-negotiating ports
with RJ-45 connectors, 1000Base-SX/LX/BX
fiber port

IEEE 802.3u 100Base-TX
IEEE 802.3ab 1000Base-T
IEEE 802.3z 1000Base-SX/LX

10 / 20Mbps half / full-duplex
100 / 200Mbps half / full-duplex
2000Mbps full-duplex

148,810pps for 100Mbps
1,488,100pps for 1000Mbps

2-pair UTP/STP Cat. 3, 4, 5
2-pair UTP/STP Cat. 5
4-pair UTP/STP Cat. 5
Up to 100m (328ft)
MMF (50 or 62.5μm), SMF (9 or10μm)

Per port – 10/100/1000TX: 10/100, 1000
1000SX/LX/BX: 1000

(1.18” (W) × 3.23” (D) × 4.49” (H))

0.25A @ 24VDC

Tested for functional operation @

-20°C to 70°C (-4°F to 158°F)

EN61000-6-4:
EN55022, EN61000-3-2, EN61000-3-3

19

EX32905/EX32914 series www.etherwan.com

EMS EN61000-6-2:

Environmental Test
Compliance

EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)

IEC60068-2-6 Fc (Vibration Resistance)
IEC60068-2-27 Ea (Shock)
FED STD 101C Method 5007.1 (Free Fall w/
package)

20