Page 1
Ethernet Extender
Preface
This manual describes how to install and use the Ethernet Extender. The
Ethernet Extender introduced here provides one channel for Ethernet over
VDSL.
The Ethernet Extender fully complies with IEEE 802.3 10BaseT and IEEE
802.3u 100BaseTX standards.
In this manual, you will find:
y Product overview
y F
EATURES ON THE ETHERNET EXTENDER
y Illustrative LED functions
y Installation instructions
y Specifications
User’s Manual 1
Page 2
Ethernet Extender
Table of Contents
PREFACE ...............................................................................1
T
ABLE OF CONTENTS..............................................................2
I
NTRODUCTION .......................................................................3
P
RODUCT OVERVIEW..........................................................3
P
RODUCT FEATURES ..........................................................3
P
ACKING LIST ....................................................................3
O
NE-CHANNEL ETHERNET EXTENDER .....................................4
ORTS ...............................................................................4
P
VDSL
RONT PANEL & LEDS.......................................................4
F
MODE SETTINGS ......................................................4
INSTALLATION ........................................................................6
ELECTING A SITE FOR THE EQUIPMENT ..............................6
S
ONNECTING TO POWER.....................................................6
C
I
NSTALLING IN A CHASSIS ...................................................7
U
SE PANEL MOUNT KIT........................................................8
S
PECIFICATIONS...................................................................10
2 User’s Manual
Page 3
Ethernet Extender
Introduction
The Ethernet Extender provides one channel for Ethernet over VDSL. It
can be used as a stand-alone device or with a standard 19” chassis.
Product Overview
Product Features
y One 10/100BaseTX (TX) Ethernet port with RJ-45 connector
y Auto negotiation of speed and duplex mode on TX port
y Auto MDIX on TX port
y Complies with IEEE 802.3 10BaseT and IEEE 802.3u 100BaseTX
standards
y One Ethernet over VDSL port with RJ-11 connector
y Ethernet over VDSL port auto senses the speed of
1/3/5/10/15/20/25/30Mbps
y One DIP switch for configuring VDSL local or remote mode
S
TATUS LEDS
y External AC to DC power adapter
y Used as a stand-alone device or with a chassis
y Hot-swappable when used with a chassis
Packing List
When you unpack this product package, you will find the items listed below.
Please inspect the contents, and report any apparent damage or missing
items immediately to our authorized reseller.
y
THE ETHERNET EXTENDER
y
USER’S MANUAL
y AC to DC Power Adaptor
User’s Manual 3
Page 4
Ethernet Extender
One-Channel Ethernet Extender
Ports
The Ethernet Extender provides one TX port and one VDSL port.
For the TX port, it uses RJ-45 connector and auto senses the speed of
10/100Mbps.
For the VDSL port, it uses RJ-11 connector and auto senses the speed of
1/3/5/10/15/20/25/30Mbps.
VDSL Mode Settings
VDSL mode settings are made very simple by means of a DIP (Dual Inline
Package) switch at the rear panel of the VDSL Extender.
DIP switch
There is one pin on the DIP switch for VDSL mode settings. Refer to the
table below for more details. One end must be set to Loc and the other to
Rmt when two devices are connected.
Loc Rmt
The device operates in local mode The device operates in remote mode
Front Panel & LEDs
LED Indicators
The LED indicators give you instant feedback on status of the Ethernet
Extender:
4 User’s Manual
Page 5
Ethernet Extender
LEDs State Indication
Pwr
Ethernet
Lnk/Act
Fdx
Ethernet over VDSL
1
2
Steady Power on
P
WR STANDS FOR POWER
Off Power off
Steady A valid Ethernet connection established
Lnk stands for LINK
Flashing Transmitting or receiving Ethernet data
Act stands for ACTIVITY
Off Neither valid Ethernet connection established nor
transmitting/receiving Ethernet data
Steady Ethernet Connection in full duplex mode
Fdx stands for FULL-DUPLEX
Flashing Collision occurred
Off Ethernet Connection in half-duplex mode
GREEN
Amber The VDSL port transmitting/receiving at 3Mbps, up to 1700M
GREEN THE VDSL PORT TRANSMITTING/RECEIVING AT 5MBPS, UP TO 1600M
The VDSL port transmitting/receiving at 1Mbps, up to 1900M
Amber The VDSL port transmitting/receiving at 10Mbps, up to 1500M
3
GREEN
Amber The VDSL port transmitting/receiving at 20Mbps, up to 1000M
4
GREEN
Amber The VDSL port transmitting/receiving at 30Mbps, up to 600M
Rmt Steady The device operates in remote mode
Loc Steady The device operates in local mode
Err Steady Error occurred
Lnk Steady A valid VDSL connection established
User’s Manual 5
The VDSL port transmitting/receiving at 15Mbps, up to 1400M
The VDSL port transmitting/receiving at 25Mbps, up to 800M
Page 6
Ethernet Extender
Installation
This chapter gives step-by-step installation instructions for the Ethernet
Extender.
Selecting a Site for the Equipment
As with any electric device, you should place the equipment where it will
not be subjected to extreme temperatures, humidity, or electromagnetic
interference. Specifically, the site you select should meet the following
requirements:
z The ambient temperature should be between 0 to 60 degrees Celsius.
z The relative humidity should be less than 90 percent, non-condensing.
z Surrounding electrical devices should not exceed the electromagnetic
field (RFC) standards for IEC 801-3, Level 2 (3V/M) field strength.
z Make sure that the equipment receives adequate ventilation. Do not
block the ventilation holes on each side of the equipment.
z The power outlet should be within 1.8 meters of the product.
Connecting to Power
y This Ethernet Extender is a plug-and-play device.
y Connect the supplied AC to DC power adaptor to the receptacle on the
rear panel of the Ethernet Extender, and then attach the plug into a standard
AC outlet with a voltage range from 100 to 240VAC.
6 User’s Manual
Page 7
Ethernet Extender
Installing in a Chassis
The Ethernet Extender can be fit into any of the expansion slots on a
special designed chassis.
y First, install the Ethernet Extender onto a carrier supplied with the chassis:
Step 1- Unscrew the carrier from the desired expansion slot on the chassis.
Step 2- Fit the Ethernet Extender onto the carrier.
User’s Manual 7
Page 8
Ethernet Extender
y When the Ethernet Extender is completely seated onto the carrier, insert
the carrier to the guide rails of the expansion slot.
y Carefully slide in the carrier until it is fully and firmly fit the chassis. Fasten
the screws onto the carrier.
<NOTE> Never insert any Ethernet Extender into the chassis directly
without using the supplied carriers. The carriers allow secure and consistent
placement of the Ethernet Extenders into the chassis backplane without
causing any damage.
Use panel mount kit
The Ethernet Extender can use panel mount kit to fix on the panel.
8 User’s Manual
Page 9
Step 1- Loosen the screws by the side of the unit.
Ethernet Extender
Step 2- Fit the panel mount kit onto the unit and fasten the screws.
User’s Manual 9
Page 10
Ethernet Extender
Specifications
Applicable Standards IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
E
THERNET OVER VDSL
Fixed Ports 1 x 10/100Mbps Ethernet port with RJ-45 connector
1 x Ethernet over VDSL port with RJ-11 connector
Speed
10BaseT
100BaseTX
E
THERNET OVER VDSL
10/20Mbps for half/full-duplex
100/200Mbps for half/full-duplex
1, 3, 5, 10, 15, 20, 25, 30MBPS
Cable
10BaseT
100BaseTX
E
THERNET OVER VDSL
Switching Method Store-and-Forward
Forwarding rate 14,880/148,800pps for 10/100Mbps
Dimensions W80.3 × D109.2 × H23.8 mm
Weight 0.15kg (5.3 oz.)
Power External power adaptor 12VDC, 0.2A
Power Consumption 2.4W Max.
Operating Temperature 0°C ~ 60°C
Storage Temperature -25°C ~ 70°C
Humidity 10 ~ 90%, non-condensing
Emissions FCC part 15 Class A, CE Mark
2-pair UTP/STP Cat. 3, 4, 5
2-
PAIR UTP/STP CAT. 5
Straight telephone wires
Per Unit- (7 LEDs): Pwr; Rmt, Loc, 1, 2, 3, 4 LED Indicators
Per Port-
RJ-45 (2 LEDs): Lnk/Act; Fdx
(2 LEDS): ERR, LNK
RJ-11
X 4.3 X 0.94 IN.)
(3.2
10 User’s Manual
Loading...