EtherWan EX26262F Series Installation Guide
EX26262F
4/24/2017
W70G-EX26262FQ1
EX26262F Series Managed Ethernet Switch
Installation Guide
1 Unpacking
Open the carton and unpack the items. Your
package should include:
EX26262F Switch
AC Power cord
Four adhesive rubber feet
Installation guide
Mounting kit
RJ45 to DB9 console cable
If any items are missing or damaged, notify your
EtherWAN representative. If possible, save the
carton and packing material in case you need to
ship or store the switch in the future.
2 Equipment Needed
Category 5 or better cable for RJ-45 ports
Appropriate fiber cables for fiber ports
Appropriate SFP cable and SPF modules for
SFP ports
3 Select a Location
Installation: Bracket-mount. Use the
enclosed screws and brackets to mount the
switch in an open or enclosed rack.
Identify a power source within 6 feet (1.8
meters).
Choose a dry area with ambient temperature
between 0 and 45ºC (32 and 113ºF).
Keep away from heat sources, sunlight, warm
air exhausts, hot-air vents, and heaters.
Be sure there is adequate airflow.
4 Connect Power
Connect the AC power cord to the AC power
receptacle of switch.
Connect the other end of the AC power cord
to the AC power outlet.
Check the SYS LED. If it is ON, the power is
connected correctly.
PoE budget is 370 watts
5 Connect to the Data Ports
The EX26262F has the following ports:
24 10/100/1000 Mbps copper PoE ports
2 Gigabit combo ports (RJ-45 & SPF)
6 Mode/Reset Button
By pressing and holding the Mode/Reset Button,
the following tasks can be performed.
0 ~ 2 seconds: Change the LED Mode between
Link/Act/Speed mode or PoE
2 ~ 7 seconds: Reset the switch, reloading
the last saved configuration settings.
7 ~ 12 seconds: Restore the switch to factory
default settings
7 Console Configuration
Connect to the switch console by connecting
the RJ45 to DB9 console cable to the RJ45
console port of the switch and to the serial
port of the computer running a terminal
emulation application (such as
HyperTerminal or Putty).
Configuration settings of the terminal-
emulation program: Baud rate: 115,200bps,
Data bits: 8, Parity: none, Stop bit: 1, Flow
control: none.
The default login name is “root,” no
password.
8 Web Configuration
Log in to the switch by launching a web
browser and entering 192.168.1.10 in the
address bar.
Copyright 2017 EtherWAN Systems, Inc. Page 1
All Rights Reserved
EX26262F Managed Ethernet Switch Installation Guide
EX26262F
4/24/2017
W70G-EX26262FQ1
Color
State
Description
Green
On
Switch is powered ON correctly.
Off
Switch is not receiving power.
Red
On
An abnormal state, such as excessive
operating temperature, has been
detected.
Color
State
Description
Green
On
Port Status LEDs display link status,
network activity and speed of each port.
Green
On
RJ45 Port Status LEDs display PoE
status of each port.
Color
State
Description
RJ45
Green
On
Port is enabled with link
established, connection speed is
1000Mbps.
Green
Blinking
Port is transmitting/receiving
packets, and connection speed is
1000Mbps.
Amber
On
Port is enabled with link
established, connection speed is
10/100Mbps.
Amber
Blinking
Port is transmitting/receiving
packets, connection speed is
10/100Mbps.
--
Off
Port has no active connection, or
has been disabled.
SFP
Green
On
Port is enabled with link
established, connection speed is
1000Mbps.
Green
Blinking
Port is transmitting/receiving
packets, connection speed is
1000Mbps.
Amber
On
Port is enabled with link
established, connection speed is
100Mbps.
Amber
Blinking
Port is transmitting/receiving
packets, connection speed is
100Mbps.
--
Off
Port has no active connection, or
has been disabled.
Color
State
Description
RJ45
Green
On
Port is enabled and supplying power
to connected device.
Amber
On
Abnormal state has been detected.
--
Off
Port has no active connection, or has
been disabled.
Enter the default login ID: root (no password)
and click “Login.” The system information
screen will display as shown below.
9 Front Panel LEDs
System
Mode
Port Status – Link/ACT/Speed
Port Status - PoE
Copyright 2017 EtherWAN Systems, Inc. Page 2
All Rights Reserved
Loading...