EtherWan EDR-120 series Specifications

120W Single Output Industrial DIN RAIL

EDR-120 series

R33100

RoHS

■ Features ■ Applications
Universal AC input / Full range
Protections: Short circuit / Overload / Over voltage

/ Over temperature

Cooling by free air convection

Industrial control system
Semiconductor fabrication equipment
Factory automation
Electro-mechanical apparatus

Can be installed on DIN rail TS-35/7.5 or 15
UL 508 (industrial control equipment) approved
EN61000-6-2(EN50082-2) industrial immunity level
100% full load burn-in test
2 years warranty

Bauar
Sicherheit

egel gema
od
be

wac g

www.
ID 2000000000

tgepruf t

os

tuv.com

■ Description

EDR-120 is one economical slim 120W DIN rail power supply series, adapt to be installed on TS-35/7.5
or TS-35/15 mounting rails. The body is designed 40mm in width, which allows space saving inside the
cabinets. The entire series adopts the full range AC input from 90VAC to 264VAC and conforms to
EN61000-3-2, the norm the European Union regulates for harmonic current.
EDR-120 is designed with metal housing that enhances the unit's power dissipation. With working efficiency
up to 88.5%, the entire series can operate at the ambient temperature between -20 and 60 under air ℃℃
convection. It is equipped with constant current mode for over-load protection, fitting various inductive
or capacitive applications. The complete protection functions and relevant certificates for industrial control
apparatus (UL508, TUV EN60950-1, and etc.) make EDR-120 a very competitive power supply solution
for industrial applications.

■ Model Encoding

-12EDR - 120

Output voltage

Output wattage

Series name

File Name:EDR-120-SPEC 2018-01-12

120W Single Output Industrial DIN RAIL

SPECIFICATION

MODEL

DC VOLTAGE

RATED CURRENT

CURRENT RANGE

RATED POWER

RIPPLE & NOISE (max.)

OUTPUT VOLTAGE ADJ. RANGE

VOLTAGE TOLERANCE

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

HOLD UP TIME (Typ.)

VOLTAGE RANGE

FREQUENCY RANGE

INPUT

PROTECTION

ENVIRONMENT

SAFETY &

EMC

(Note 4)

NOTE

EFFICIENCY (Typ.)

AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

OVERLOAD

OVER VOLTAGE

OVER TEMPERATURE

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

SAFETY STANDARDS
WITHSTAND VOLTAGE

ISOLATION RESISTANCE
EMC EMISSION

EMC IMMUNITY
MTBF

DIMENSIONOTHERS

PACKING

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.

5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power.
In case the adjacent device is a heat source, 15mm clearance is recommended.

6. Derating may be needed under low input voltage. Please check the derating curve for more details.

7. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃

EDR-120 series

EDR-120-12

12V

10A

0 ~ 10A

120W

100mVp-p

Note.2

12 ~ 14V
±2.0%

Note.3

±0.5%
±1.0%

1200ms, 60ms/230VAC 2500ms, 60ms/115VAC at full load

16ms/230VAC 10ms/115VAC at full load

90 ~ 264VAC 127 ~ 370VDC

Note.6

47 ~ 63Hz

85%

2.25A/115VAC 1.3A/230VAC
20A/115VAC 35A/230VAC

<1mA / 240VAC

105 ~ 130% rated output power

Protection type : Constant current limiting, recovers automatically after fault condition is removed

14 ~ 17V

Protection type : Shut down o/p voltage, re-power on to recover

Shut down o/p voltage, re-power on to recover

-20 ~ +60 (Refer to "Derating Curve")℃

20 ~ 95% RH non-condensing

-40 ~ +85 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 50 )

Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6

UL508, TUV EN60950-1, , BSMI CNS14336-1 approved;(meet EN60204-1)EAC TP TC 004

I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25 / 70% RH℃

Compliance to EN55032 (CISPR32) Class A, EN61000-3-2,-3, Class AEAC TP TC 020, CNS13438

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), heavy industry level, criteria A, EAC TP TC 020

474.6K hrs min. MIL-HDBK-217F (25 )℃

40*125.2*113.5mm (W*H*D)

0.6Kg; 20pcs/13Kg/1.16CUFT

EDR-120-24 EDR-120-48

24V 48V

5A 2.5A

0 ~ 5A 0 ~ 2.5A

120W 120W

120mVp-p 150mVp-p

24 ~ 28V 48 ~ 55V

±1.0% ±1.0%
±0.5% ±0.5%
±1.0% ±1.0%

[DC input operation possible by connecting AC/L(+), AC/N(-)]

87.5%

29 ~ 33V

88.5%

56 ~ 65V

File Name:EDR-120-SPEC 2018-01-12