EtherWan ED3638 Quick Start Guide

ED3638 www.etherwan.com

cable.

Quick Start Guide

This quick start guide describes how to install and use the Hardened Ethernet Extender. This is the Hardened Ethernet Extender of choice for harsh environments constrained by space.

Installation

ED3638T (Transmitter): This is a PoL (Power over Link) transmitter. Data and power

can be delivered at the same time through coaxial cable to turn on and communicate with ED3638R (Receiver) via BNC interface.

ED3638R (Receiver): This is a PoL (Power over Link) Receiver. ED3638R (Receiver) can be powered either by ED3638T (Transmitter) through coaxial cable or power supply. The Ethernet port supports IEEE802.3at PoE/PSE for fulfilling PoE/PD application.

• Removes the device power before installation.

• Removes the device power before any I/O and DIP switch configuration.

• Do not connect ED3638T and ED3638R to the same power source. Devices

may be damaged due to power loop back through the PoL linked via coaxial

PoL (Power over Link) Mode Enable Installation

• Ensures all power sources are disconnected from ED3638T and ED3638R.

• Ensures ED3638T PoL (Power over Link) DIP switch is in On position (Up position).

• Sets ED3638T Type DIP switch to Perf (Performance, Up position) to acquire better

Line Speed (but poor noise immunity). Or sets Type DIP switch of ED3638T to Std (Standard, Down position) to acquire standard Line Speed (but better noise immunity).

• Checks if ED3638R Mode is set to Rmt on DIP switch (Remote, Up position).

• Connects one end of the coaxial cable to BNC interface of the ED3638T and the

other end to BNC interface of the ED3638R.

• Connects power source to ED3638T.

• Data and power can be delivered from ED3638T, and at the same time through

coaxial cable to turn on and communicate with ED3638R.

<Note> The equipment is designed for building installation and not intended to be connected to exposed (outside plant) networks including campus environment or equivalent.

PoL (Power over Link) Mode Disable Installation

• For longer distance (e.g. over 1.4km) extension application, ED3638R may not be able to receive power from ED3638T. A separate power may be applied on ED3638R.

• Ensures all power sources are disconnected from ED3638T and ED3638R.

• Ensures ED3638T PoL (Power over Link) DIP switch is in Off position (Down

position).

• Sets ED3638T Type DIP switch to Perf (Performance, Up position) to acquire better Line Speed (but poor noise immunity). Or sets Type DIP switch of ED3638T to Std (Standard, Down position) to acquire standard Line Speed (but better noise immunity).

User’s Manual 1

ED3638 www.etherwan.com

ED3638T

ED3638R

Power supply suggestion

30 watts application

SDR-120-48 / DR-120-48 (120W 48VDC)

For one pair

SDR-240-48 (240W 48VDC)

For three pairs

SDR-480-48 (480W 48VDC)

For seven pairs

• Connects power source to ED3638T.

• Checks if ED3638R Mode is set to Rmt on DIP switch (Remote, Up position).

• Connects power source to ED3638R.

• Connects one end of the coaxial cable to BNC interface of the ED3638T and the

other end to BNC interface of the ED3638R.

• Data can be transmitted between ED3638T and ED3638R via coaxial cable.

Physical Description

The Port Status LEDs and Power Inputs

• DC Terminal Block Power Inputs: 2.5A @ 48VDC (Peak current 3.26A). two pairs of power inputs can be used to power up this Ethernet Extender. Redundant power supplies function is supported. You only need to have one power input connected to run the Ethernet Extender.

• DC JACK Power input: 2.5A @ 48VDC (Peak current 3.26A).

User’s Manual 2

There are

ED3638 www.etherwan.com

Power Input Assignment

Power1

48VDC

DC Jack

Power Ground

DIP Switch

ED3638T

PoL

Disable Power over Link

Enable Power over Link

Better noise immunity

Poor noise immunity

ED3638R

Loc (Local)

Rmt (Remote) Better noise immunity

Poor noise immunity

LEDs

State

Indication

1/2/3

Steady

Power received

Off

Power off

Steady

Power Ethernet extension interface function is enabled

No power is transmitted over Ethernet extension Steady

Powered device (PD) is connected

Off

Powered device (PD) is disconnected

Steady

A valid Extender connection established

Fast Flashing

Off

Extender interface connection is not established

Line Steady

PoE power can be transmitted for PD

All off

No PoE power can be transmitted for PD

Steady

A valid Ethernet connection established

Flashing

Data transmission or receiving

Off

Non-Ethernet connection is established

Steady

Link speed at 100Mbps

＋

Power2

Power3

Down Up

T:46-57V / R:46-57V DC

－＋

T:46-57V / R:46-57V DC

－

Earth Ground

Terminal Block

Type

Mode

Type

Power

PoL

PoE

Link

Speed PSE Output

Std (Standard) Standard line speed

Set ED3638R to Local Mode Std (Standard) Standard line speed

Off

Slow Flashing

Steady Displays the link speed in Mbps

Green

Yellow

interface

Data transmission or receiving

Extender port under negotiation mode

Off Link speed at 10Mbps

Perf (Performance) Better line speed

Set ED3638R to Remote Mode Perf (Performance) Better line speed

User’s Manual 3

ED3638 www.etherwan.com

Power over Link (PoL) Enabled

Distance

Data Rate

ED3638R PoE Output

400M

100Mbps

30.0W

800M

60Mbps

15.4W

1000M

50Mbps

12.0W

1200M

45Mbps

8.0W

1600M

20Mbps

6.0W

1800M

15Mbps

4.0W

Power over Link (PoL) Disabled Power Supply Applied on ED3638R

Distance

Data Rate

ED3638R PoE Output

2000M

9Mbps

30.0W

2200M

6Mbps

30.0W

2400M

4Mbps

30.0W

Regular Port

PoE Port

1

Output Transmit Data +

2

Output Transmit Data -

3

Input Receive Data +

4 Positive (VCC+)

5 Positive (VCC+)

6

Input Receive Data -

7 Negative (VCC-)

8 Negative (VCC-)

<Note> The Reference Performance is tested on 5C2V / RG6AU Coaxial Cable on a roll type (Cable impedance: 75ohm).

10/100Base-TX and Ethernet Extender Connectors

10/100Base-TX Connection The following lists the pinouts of 10/100Base-TX RJ-45 port.

User’s Manual 4

ED3638 www.etherwan.com

Functional Description

• Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environment.

• Ethernet port: Supports IEEE802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps, full/half-duplex; Auto MDI/MDIX.

• Auto data rate negotiation for Ethernet extension interface.

• 5C2V/RG6AU coaxial cable for BNC connector.

• Six speeds with speed indicator LEDs on front panel of unit, up to

100Mbps @ about 600meters (1,968ft.), down to 1Mbps @ about 3,000meters (9,842ft.).

• Supports Power over Link (PoL) and provides IEEE802.3at power output up to 500meters (1,640ft.) and IEEE802.3af power output up to 800meters (2,624ft.).

• Supports Power over Ethernet application up to 1,900meters (6,233ft.) for Max. 5 watts power consumed PoE powered devices.

• Power consumption:

- Enable Power over Link (PoL) function: Max. 65Watts

- Disable Power over Link (PoL) function: ED3638T: Max. 5W.

ED3638R: Max. 35W with PoE output, Max. 5W without PoE

• Power Supply: Redundant T:46-57V / R:46-57V DC Terminal Block

• Operating temperature range @ -40℃ to 7 5℃ (-40℉ to 167℉). Tested

• Supports Din-Rail or Panel Mounting installation.

output.

power inputs and 48VDC Latched DC JACK interface.

for functional operation @ -40℃ to 85 ℃ (-40℉ to 185℉).

User’s Manual 5

ED3638 www.etherwan.com

Preface

This manual describes how to install and use the Hardened Ethernet Extender. The Hardened Ethernet Extender introduced here provides one channel for Ethernet over existing coaxial cable.

The Hardened Ethernet Extender fully complies with IEEE802.3 10Base-T and IEEE802.3u 100Base-TX standards.

In this manual, you will find:

• Product overview

• Features on the Hardened Ethernet Extender

• Illustrative LED functions

• Installation instructions

• Specifications

User’s Manual 6

ED3638 www.etherwan.com

One-Channel Hardened Ethernet Extender

Ports

The Hardened Ethernet Extender provides TX ports and one Ethernet Extender port. For the TX ports, it uses RJ-45 connector and auto senses the speed of 10/100Mbps. For the Ethernet Extender port, it uses BNC connectors and auto senses the speed of Link (below 20)/20/40/60/80/100Mbps.

Ethernet Extender Mode Settings

Ethernet Extender mode settings are made very simple by means of a DIP (Dual Inline Package) switch on the top panel of the Hardened Ethernet Extender.

DIP Switch

Down Up

Switch

Perf (Performance) Better line speed

Rmt (Remote)

Better line speed

Type

Mode

Type

Std (Standard) Standard line speed

Loc (Local)

Standard line speed

User’s Manual 10

ED3638 www.etherwan.com

LEDs

State

Indication

Steady

Power received

Off

Power off

Steady

Power Ethernet extension interface function is enabled

No power is transmitted over Ethernet extension interface

Steady

Powered device (PD) is connected

Off

Powered device (PD) is disconnected

Steady

A valid Extender connection established

Flashing

Slow Flashing

Off

Extender interface connection is not established

Line Speed

PSE Output

Steady

PoE power can be transmitted for PD

All off

No PoE power can be transmitted for PD

Steady

A valid Ethernet connection established

Flashing

Data transmission or receiving

Off

Non-Ethernet connection is established

Steady

Link speed at 100Mbps

Off

Link speed at 10Mbps

Power over Link (PoL) Enabled

Distance

Data Rate

ED3638R PoE Output

400M

100Mbps

30.0W

800M

60Mbps

15.4W

1000M

50Mbps

12.0W

1200M

45Mbps

8.0W

1600M

20Mbps

6.0W

1800M

15Mbps

4.0W

Front Panel & LEDs

LED Indicators

The LED indicators give you instant feedback on status of the Hardened Ethernet Extender:

Power 1/2/3

PoL

PoE

Link

Off

Fast

Steady Displays the link speed in Mbps

Green

Yellow

Data transmission or receiving

Extender port under negotiation mode

User’s Manual 11

ED3638 www.etherwan.com

Power Supply Applied on ED3638R

Distance

Data Rate

ED3638R PoE Output

2000M

9Mbps

30.0W

2200M

6Mbps

30.0W

2400M

4Mbps

30.0W

10/100Base-TX Connection

Regular Port

PoE Port

1

Output Transmit Data +

2

Output Transmit Data -

3

Input Receive Data +

4 Positive (VCC+)

5 Positive (VCC+)

6

Input Receive Data -

7 Negative (VCC-)

8 Negative (VCC-)

Power over Link (PoL) Disabled

<Note> The Reference Performance is tested on 5C2V / RG6AU Coaxial Cable on a roll type (Cable impedance: 75ohm).

10/100Base-TX and Ethernet Extender Connectors

The following lists the pinouts of 10/100Base-TX RJ-45 port.

User’s Manual 12

ED3638 www.etherwan.com

Installation

This chapter gives step-by-step installation instructions for the Hardened Ethernet Extender.

Selecting a Site for the Equipment

As with any electric device, you should place the equipment where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements:

• The Surrounding Air temperature should be between -40 to 75 degrees Celsius.

• The relative humidity should be less than 95 percent, non-condensing.

• Surrounding electrical devices should not exceed the electromagnetic field (RFC)

standards.

• Make sure that the equipment receives adequate ventilation. Do not block the ventilation holes of the equipment.

• The power outlet should be within 1.8 meters of the product.

DIN Rail Mounting

Fix the DIN rail attachment plate to the back panel of the Hardened Ethernet Extender.

Installation: Place the Hardened Ethernet Extender on the DIN rail from above using the slot. Push the front of the Hardened Ethernet Extender toward the mounting surface until it audibly snaps into place.

Removal: Pull out the lower edge and then remove the Hardened Ethernet Extender from the DIN rail.

User’s Manual 13

ED3638 www.etherwan.com

User’s Manual 14

ED3638 www.etherwan.com

Connecting to Power

Redundant DC Terminal Block Power Inputs or 48VDC DC Jack:

Redundant DC Terminal Block Power Inputs

There are two pairs of power inputs can be used to power up this device. You only need to have one power input connected to run the Hardened Ethernet Extender.

Step 1: Connect the DC power cord to the plug-able terminal block on the Hardened Ethernet Extender, and then plug it into a standard DC outlet.

Step 2: Disconnect the power cord if you want to shut down the Hardened Ethernet Extender.

48VDC DC Jack

Step 1: Connect the supplied AC to DC power adapter to the receptacle on the topside of the Hardened Ethernet Extender.

Step 2: Connect the power cord to the AC to DC power adapter and attach the plug into a standard AC outlet with the appropriate AC voltage.

User’s Manual 15

ED3638 www.etherwan.com

Power Input Assignment

Power1

48VDC

DC Jack

Power Ground

＋

Power2

Power3

T:46-57V / R:46-57V DC

－＋

T:46-57V / R:46-57V DC

－

Earth Ground

Terminal Block

User’s Manual 16

ED3638 www.etherwan.com

Applicable Standards

IEEE802.3 10Base-T, IEEE802.3u 100Base-TX

10/100Mbps Ethernet ports with RJ-45 connectors 1 x Ethernet Extender port with BNC connector

Speed

Ethernet Extender

Coaxial cable

(1.97” (W) x 4.33” (D) x 5.31” (H))

Weight

0.77Kg (1.7lbs.)

48VDC (Peak current 3.26A)

Enable PoL: Max. 65Watts

Max. 5W without PoE output

-40℃ ~ 75℃ (-40℉ ~ 167℉)

Humidity

5 ~ 95%, non-condensing

FCC Part 15, Class A

IEC60068-2-6 Fc (Vibration Resistance)

IEC60068-2-32 Ed (Free Fall)

Specifications

Fixed Ports

10Base-T 100Base-TX Ethernet Extender

Switching Method Store-and-Forward

Forwarding rate 14,880/148,810pps for 10/100Mbps Cable

10Base-T 100Base-TX

LED Indicators

Dimensions

Power

Power Consumption

Operating Temperature

Storage Temperature

EMI

EMS

Environmental Test Compliance

User’s Manual 17

10/20Mbps for half/full-duplex 100/200Mbps for half/full-duplex Link (Below 20), 20, 40, 60, 80, 100Mbps

4-pair UTP/STP Cat. 3, 4, 5 up to 100m 4-pair UTP/STP Cat. 5 up to 100m

Per Unit (3 LEDs)- Power1, Power2, Power3 ED3638TPoL; Line Speed (Mbps): Link, 20, 40, 60, 80, 100 ED3638RPoE; Line Speed (Mbps): Link, 20, 40, 60, 80, 100; PSE Output (Watts): 5, 15, 30 50mm (W) × 110mm (D) x 135mm (H)

Terminal Block: T:46-57V / R:46-57V DC DC Jack: 48VDC, External AC/DC required Terminal Block & DC Jack Power Inputs: 2.5A @

Disable PoL: ED3638T: Max. 5W ED3638R: Max. 35W with PoE output

Tested for functional operation @

-40℃ ~ 85℃ (-40℉ ~ 185℉)

EN61000-6-4: EN55022, EN61000-3-2, EN61000-3-3 EN61000-6-2: EN61000-4-2 (ESD Standard) EN61000-4-3 (Radiated RFI Standards) EN61000-4-4 (Burst Standards) EN61000-4-5 (Surge Standards) EN61000-4-6 (Induced RFI Standards) EN61000-4-8 (Magnetic Field Standards)

IEC60068-2-27 Ea (Shock)

EtherWan ED3638 Quick Start Guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Quick Start Guide

Installation

Physical Description

The Port Status LEDs and Power Inputs

10/100Base-TX and Ethernet Extender Connectors

Functional Description

Table of Contents

Product Overview

Product Features

Packing List

One-Channel Hardened Ethernet Extender

Ports

Ethernet Extender Mode Settings

DIP Switch

Front Panel & LEDs

LED Indicators

10/100Base-TX and Ethernet Extender Connectors

Installation

Selecting a Site for the Equipment

DIN Rail Mounting

Connecting to Power

Redundant DC Terminal Block Power Inputs

48VDC DC Jack

Specifications