eNEXHO - NT
Home automation / Internet module
Assembly and operating instructions
› Please read these instructions carefully and keep them for future consultation. eNEXHO range equipment must be installed
by an accredited, qualied electrician and must observe Low Voltage Regulations. The installation as a whole should meet the
provisions of aforesaid regulation. Any claim presented will be deemed invalid if the prevailing regulations have not been met.
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
G ENERAL INFORMATION
With your choice of ETHERMA you have decided on an inge-
nious heating solution. We thank you for your condence. In
us you have a competent partner with more than 30 years of
experience. ETHERMA relies on constant innovation , highest
product quality and modern design.
We support you with comprehensive personalized services and
nd the right product solution for you.
The following instructions will help you, to use your ETHERMA
quality product as effective as possible. They contain important
information about safety, installation, use and maintenance of
the devices. Please read the information in this instruction
carefully and keep them for feedback at a later time on.
T ABLE OF CONTE NTS
INSTRUCTIONS FOR USE ................................................................................ 24
General information ..................................................................................24
DOWNLOAD APP........................................................................................ 24
COMMISSIONING ....................................................................................... 24
Positioning .........................................................................................25
How to synchronize a second device with an installation already done with the original device? ...................25
How to reset the nexho application downloaded in my device? ...............................................26
How to set the time? .................................................................................26
How to change the conguration passwords? .............................................................26
How to deactivate the password request in NEXHO application?..............................................26
How to reset the internet module NEXHO-NT? ............................................................27
HOW TO INSTALL A LAVA®-R DESIGN INFRARED HEATER IN THE eNEXHO-SYSTEM?............................. 28
How to change the name of one heating zone? ............................................................28
How to change the temperature in the different rooms? ....................................................28
How to activate the programs in the LAVA®-R design infrared heater?........................................ 28
How to deactivate the programs in your LAVA®-R design infrared heater?.....................................28
How to personalize or modify the programs of your LAVA®-R design infrared heater?........................... 28
How to install a LAVA®-R design infrared heater in a "repeater mode"?.......................................28
WORKING WITH eNEXHO-CL THERMOSTATS................................................................ 29
How to install an eNEXHO-CL thermostat module in the automation.......................................... 29
How to change a name of a thermostat zone?............................................................. 29
How to change the temperature in the different rooms? ....................................................29
How to activate the programs in the thermostat modules eNEXHO-CL? .......................................29
How to deactivate the programs in the thermostat modules eNEXHO-CL? .....................................30
How to personalize or modify the programs of your thermostat modules eNEXHO-CL? ..........................30
WORKING WITH eNEXHO-PR PRESENCE DETECTORS ........................................................ 30
How to install an eNEXHO-PR presence detector in the automation network? .................................30
WORKING WITH eNEXHO-IN FLOOD DETECTORS ............................................................ 30
How to install an eNEXHO-IN ood detector in the automation network? ......................................30
WORKING WITH eNEXHO-IC / HU FIRE- ODER SMOKE DETECTORS ............................................. 31
How to install an eNEXHO-IC re detector or an eNEXHO-HU smoke detector in the automation network?..........31
WORKING WITH eNEXHO-NM NUMERIC REMOTE CONTROL ................................................... 31
How to install an eNEXHO-NM numeric remote control in the automation network?............................. 31
22
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
WORKING WITH eNEXHO-CP POWER CONTROL MODULES .................................................... 31
How to install eNEXHO-CR power control modules in the automation network? ................................31
If this is the rst thermostat that you install in the zone:.................................................... 31
How to change a name of a power control module? ........................................................31
How to delete a power control module from the list? .......................................................32
How to activate/deactivate a power control module from your application?.....................................32
How to activate the programs in a power control module? ..................................................32
WORKING WITH eNEXHO-IL LIGHTING MODULES............................................................ 32
How to install an eNEXHO-IL lighting module in the automation network?..................................... 32
How to delete a lighting module from the list? ............................................................32
How to activate the programs in a lighting module?........................................................32
How to deactivate the programs in a lighting module?...................................................... 33
How to personalize the programs of your lighting modules?................................................. 33
WORKING WITH eNEXHO-PS BLINDS MODULES ............................................................. 33
How to install an eNEXHO-PS blinds module in the automation network? .....................................33
How to delete a blinds module from the list? .............................................................33
How to open and close a blind?......................................................................... 33
How to activate the programs in a blinds module? .........................................................33
How to deactivate the programs in a blinds module? .......................................................34
How to personalize the programs of your blinds modules? ..................................................34
CONFIGURE THE SECURITY MODE ........................................................................ 34
How to modify the security password.................................................................... 34
How to receive security alarms in your mobile device? .....................................................34
How to congure the actions that your system has to take when receiving a potential security breach? .............34
How to activate/deactivate your security mode against intrusions? ...........................................35
How to activate/deactivate your security mode against intrusions from the numeric module? .....................35
How to congure the actions that your system has to take when receiving a potential ooding alert?............... 35
How to activate/deactivate the security mode against ooding? .............................................. 35
How to congure the actions that your system has to take when receiving a potential re alert? ...................35
How to activate/deactivate the security mode against res? .................................................35
WORKING WITH SCENES................................................................................. 36
What is a scene?.....................................................................................36
How to create a scene? ...............................................................................36
How to activate one scene? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
How to change a general or a security scene? ............................................................36
How to delete a general or a security scene? .............................................................36
WORKING WITH ASSOCIATIONS ........................................................................... 36
Why associate? ......................................................................................36
How can we associate? ...............................................................................36
How to make work during certain hours a day, an association of light modules? ................................37
TROUBLESHOOTING .................................................................................... 38
It has been impossible to connect with X of the X modules installed in X. ......................................38
"Impossible to connect with the internet module" .........................................................38
TECHNICAL DETAILS .................................................................................... 39
Care and maintenance................................................................................... 39
General warranty conditions ............................................................................. 40
23
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
I NSTRUC T I ONS FOR USE
General information
Thank you for purchasing ETHERMAS internet module
eNEXHO- NT.
It has been designed and manufactured in accordance with
domestic appliances' requirements pursuant to the following
standards: UNE-EN 60950, UNE-EN 301 489, UNE-EN 61000-6
and UNE-EN 300 220.
The internet module eNEXHO-NT enables you to control, by
radio frequency means, LAVA®-R design-infraredheaters
and any other device from the eNEXHO range installed in your
house, by means of radio frequency. You will be able to control
your eNEXHO installation from your smartphone, tablet or PC
using our eNEXHO application/software. Please consult our
web page www.etherma.com in order to see the operating systems that are supported by the eNEXHO application which are
available to download from their respective application/soft-
ware shops you can nd in the internet.
DOWNLOAD A PP
Once the application is downloaded and congured together
with the internet module eNEXHO-NT you will be able to surf
through the different existing menus and control, in an intuitive and user-friendly manner, controlling everything in your
system: modifying room temperatures, turning the system on/
off, changing the intensity of the lights in any given room, programming the opening of the blinds, and all of this, without the
need for cables.
Moreover, if both your installation and mobile device have internet access you will be able to do this through Internet and at
no cost. You will also have the option of conguring your internet module eNEXHO-NT so you receive ALERTS in your mobile
device if any of the alarms in your house go off: ooding, re,
smoke, intrusion, etc.
By simply following the instructions given here you will be
able to enjoy all the features and quality of life afforded by
ETHERMA products.
COMMI SSI ONI NG
The internet module eNEXHO-NT comes with a connecting
cable RJ45, one radio frequency transmitting antenna , a feeder
plug and a 230V/125V adaptor.
In order to use the internet module eNEXHO-NT it is necessary
to have a router with Wi-Fi connectivity and at least one controlling device such as a smart phone, tablet or PC with internet
connection that are not included in this package.
Synchronization with the eNEXHO-NT module is a critical process for the correct functioning of the installation. Please follow the next steps in the same order as described in order to
avoid any type of problems during the initial installation.
Download the eNEXHO application from the respective applications shop (Android Market, Apple Store, etc.) in your device.
Consult the instructions manual in your Smartphone if you are
not familiarized with the downloading of applications from virtual shops. You can also consult in our web page if you want to
24
know the different compatibilities and existing versions for the
eNEXHO application
Screw the radio frequency transmitting antenna into the corresponding connector at the back of the internet module eNEXHO-NT.
Use the data cable RJ45 to connect the internet module eNEXHO-NT to your router.
Insert the feeder plug into the corresponding connector at the
back of the internet module eNEXHO-NT and connect the feeder to the house mains.
Connect the internet module eNEXHO-NT to the power and
wait until only the green light in the module is on.
Congure your Smartphone or any other device to connect to
the Wi-Fi network generated by the router that has been con-
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
nected to the internet module eNEXHO-NT. This step is vital
in this process. Do not forget to connect yourself to the Wi-Fi
network generated by the router when you are doing the initial
installation. If you don’t do this, the application wont connect to
the internet module.
Log on the eNEXHO application. Make sure that any other device connected to the Wi-Fi network generated by your router
does not have the eNEXHO application open. If this is the case
please close the eNEXHO application on this second device.
Start the synchronization with the internet module. Your terminal screen will remain on waiting mode (if when turning on the
application the Initial Installation message does not appear,
please reset the application following the steps described in
section "HOW TO RESET THE NEXHO APPLICATION IN MY TERMINAL?" in this manual.
Activate the PUSH notications mode on your device.
You will then be able to receive messages that will inform you about new actualizations of the application, apart
from allowing you to use the security alerts that the eNEXHO
system has to offer. In order to activate PUSH notications select the conguration menu from the initial screen of eNEX-
HOs application in your mobile device or tablet. In some versions of this application this menu will appear in as an icon with
the shape of a tool at the top left part of the screen. If this icon
does not appear, press the "Menu" button of your terminal.
In the submenu select "Conguration". If you haven´t deactivated the password request, this will be by default "nexho".
Push notications require internet connection. Press now the
"Notications".
Using a small screw driver or any other alternative tool, push
the "push button switch" in the back of the internet module
eNEXHO-NT. After doing so, a message will show in your device screen indicating the status of the synchronization of your
mobile device with the internet module eNEXHO-NT. When the
synchronization progress bar nishes, the module eNEXHO-NT
will be ready to start with the conguration of your installation
with the eNEXHO product range.
It is possible that in some of the mobile devices, when starting
up the eNEXHO application, it is not necessary to push the installation "push button switch" (mainly some devices working
with Android). If you observe that when pressing the switch
the application does not connect itself, wait for a few seconds.
More than likely synchronization will take place automatically.
The eNEXHO system needs an start up installation in order
to link the application in the device with the internet module eNEXHO-NT. Moreover, the eNEXHO application protects,
with a password all the menus related with security and con-
guration
Nevertheless it is important to protect the wi access to your
router with a password if you haven’t done it previously. This
way you will double protect the system against external connections to your local network within your eNEXHO system or
any other devices and PCs in your house. Please check your
routers instructions manual to obtain more information about
wi password congurations.
Positioning
internet module eNEXHO-NT has been designed for domestic
use and must be always tted inside the house.
Do not t the device near water sources that might result in
water getting inside the device due to spraying or sprinkling.
Position your internet module in a favorable place to be reached
by the radio signals of all eNEXHO devices that have been installed, as close as possible, or in a central position.
How to synchronize a second device with an installation already done with the original device?
In order to congure a second installation (or more) please follow the next steps.
Synchronization with the eNEXHO-NT module is a critical process for the equipment to work correctly after the installation.
Please follow the next steps in the same order as described in
order to avoid any type of problem during the initial installation.
Download the eNEXHO application from the respective applications shop (Android Market, Apple Store, etc.) in your device as
you have done in the rst installation.
Congure your Smartphone or any other device to connect to
the Wi-Fi network generated by the router that has been connected to the internet module eNEXHO-NT. This step is vital
in this process. Do not forget to connect yourself to the Wi-Fi
network generated by the router when you are doing the initial
installation. If you don’t do this, the application wont connect to
the internet module.
Log on your eNEXHO application. Make sure that any other device connected to the Wi-Fi network generated by your router
does not have open the eNEXHO application. If this is the case
please close the eNEXHO application on this second device, in-
cluding the device where the rst installation was made.
Start the synchronization at the internet module. Your terminal
screen will stay on waiting mode. Using a small screw driver
or any other alternative tool, push the "push button switch" in
the back of the internet module eNEXHO-NT. After doing so, a
message will show in your device screen indicating the status
of the synchronization of your mobile device with the internet
module eNEXHO-NT. When the synchronizations progress bar
nishes, the module eNEXHO-NT will be ready to start with the
conguration of your installation with the eNEXHO product ran-
ge.
It is possible that in some of the mobile devices, when starting
up the eNEXHO application, it is not necessary to press the installation "push button switch" (mainly some devices working
with Android). If you observe that when pressing the switch
the application does not connect itself, wait for a few seconds.
More than likely synchronization will take place automatically.
As you will be able to see, the new installation does not have
the names of the zones or scenes originally congured in the
rst device. Even though you can edit them manually (please
25
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
check the corresponding sections of this manual), eNEXHO application will allow you to send the original names used during
the rst installation to future installations.
In order to complete this process please take the following
steps:
› Open both applications (the original device where the rst
installation took place and the new device). Make sure both
devices are connected to the same WI-FI network generated
by your installations router (the internet module eNEXHO-NT
must be connected to this router).
› In both devices, select the conguration menu in the ope-
ning screen of eNEXHOs application. In some versions of this
application this menu will appear as an icon in the shape of
a tool at the top left part of the screen. If this icon does not
appear, press the "Menu" button of your terminal. In the sub-
menu select "Conguration". If you haven’t deactivated the
password request button, this will be by default "nexho".
› Now press the "Communications" button in both terminals
› In the second device select the option "Receive data from
another application". eNEXHOs application in this terminal
will remain in a waiting mode.
› In the original device (where all the names of the zones have
been installed are saved) select the option "Send data to ano-
ther application".
› Now both applications will show the same names as the zo-
nes assigned originally.
The password has now been changed.
How to deactivate the password request in NEXHO application?
If you want to deactivate the password request of this applica-
tion, enter the conguration of the opening screen of eNEXHOs
application. In some versions of this application this menu will
appear as an icon with the shape of a tool at the top left part
of the screen. If this icon does not appear, press the "Menu"
button of your terminal. In the submenu select "Conguration".
If you haven’t deactivated the password request button, this will
be by default "nexho".
Now press the password button from the menu and deactivate
the options you want from the password request menu.
Please keep in mind that if you deactivate this password request, it will be easier to accidentally modify
the installation.
How to control your nexho installation from outside your
house through internet
The rst thing we will need is to have internet access from this
router. You will also need to have internet access from the device where you have downloaded the eNEXHO application when
connecting to your system.
How to reset the nexho application downloaded in my device?
Select the option "Initial Installation" from this menu. In some
of the versions of this application this option will show in an
icon with the shape of two crossed arrows at the top right hand
side of the application. If this icon is not there press the "Menu"
button in your terminal. In the Submenu that will come out select "Initial Installation".
How to set the time?
Please go to the main menu and press the "Communications"
button, once inside the communications menu press the "Send
time" button.
Please keep in mind that the conguration password
by default is "nexho". You can change this password
or deactivate it. To do any of this please go to conguration menu, then go into "Password" menu where you can
change/deactivate the password.
How to change the conguration passwords?
In order to access some of the menus within the eNEXHO application a password is needed to. Password by default is "nexho".
If you want to change this password select from the opening
screen the Congurations menu. In some versions of this application this menu will appear as an icon in the shape of a tool
at the top left part of the screen. If this icon does not appear,
press the "Menu" button of your terminal. In the submenu se-
lect "Conguration". If you haven’t deactivated the password
request button, this will be by default "nexho".
Now press the "Password" button and select the option
"Change conguration password".
Introduce the old password and accept. Introduce the new
password and accept. Repeat the new password and accept
again.
Moreover you will need to congure your router so the eNEXHO
application is allowed to receive data from outside your local
network. To make this possible you will need to congure a
"Port forwarding" in your installation router.
From a computer connected with a cable to the router, access
your routers conguration menu. This is possible by inserting
the routers direction in your browsers navigation menu (Internet Explorer, Mozilla, Firefox, Safari, etc..) Routers use as
their usual addresses http://192.168.1.1. or http://192.168.2.1.
Nevertheless, this address is often indicated in a label placed
under the router. If you cannot access the router please check
your routers instructions manual to access its conguration.
A user name and password is usually requested to access this
menu. Please check under your router or in your routers inst-
ruction manual to nd them.
Once you have accessed the conguration menu in your router,
look for a menu named "PORT FORWARDING" or "FORWARDING" or "VIRTUAL SERVERS" or "NAT", or "APPLICATIONS
AND GAMES", or "GAMIN". This will depend on the make and
model of your router.
Once in that menu please congure the following data:
› Name: Use name you want. You can use the word "nexho" if
you want to remember this conguration.
› Ports: You may be asked for just one port or for "start" and
"nish" ports. In both cases please introduce the port "6653".
› Protocol. Usually you will be able to choose between "TCP"
and "UDP" or "Both". Please mark "UDP" or "Both".
› IP Destination: It is usually the same as the routers address
excepting the last number which must be changed to 246.
For example, if your router has as an address 192.168.1.1 in
the IP Destination you must introduce 192.168.1.246
› Mark the cell "Activate" if its visible and save the changes to
nish your router conguration.
26
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
Hereafter you can see some of the examples of the conguration we have carried out on some commercial routers.
The conguration of the router is now nished.
If you´ve had problems in this section, check your routers ins-
tructions manual or look for information in the internet about
the make and model you own, in order to complete this process.
Once you have congured your router you still have to do one
nal conguration in your eNEXHO APPLICATION (the one ins-
talled in your device). In some versions of this application this
menu will appear as an icon in the shape of a tool at the top
left part of the screen. If this icon does not appear, press the
"Menu" button of your terminal. In the submenu select "Con-
guration". If you haven’t deactivated the password request
button, this will be by default "nexho". Now press the "Communications" button and activate the option "Send data to an
external server"
Please keep in mind that it can take a few minutes to nalize
this conguration while all the installation data is being con-
gured in the external server.
How to reset the internet module eNEXHO-NT?
In order to reset tie internet module eNEXHO-NT, take the following steps:
› Disconnect the network cable RJ45 that connects your ins-
tallation routers to internet module
› Press the switch button at the back of the internet module
eNEXHO-NT
› Keep it pressed for a few seconds, a blue light (led) will go on,
keep pressing the switch button until the blue light goes off.
Only after this happens, should you stop pressing the switch
button of your internet module
› Now wait until the orange led in the internet module goes off.
This process can take up to a couple of minutes. The reset
will be nished when both green and red lights are perma-
nently on
› Disconnect the power cable from your internet module.
› Connect the data cable RJ45 to the internet module eNEXHO-
NT and to your router.
› Insert the feeder plug into the corresponding connector at
the back of the internet module eNEXHO-NT and connect the
feeder to the house mains.
› Connect the internet module eNEXHO-NT to the power and
wait until only the green light in the module is on.
Please keep in mind that if you reset the internet
module eNEXHO-NT, you will lose all the information
you have saved from your installation. After this, you should
re-install all eNEXHO products in your house and synchronize again, the applications of all associated devices.
27
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
H OW TO I NSTALL A LAV A®- R DES I GN I NFRARED H E ATE R I N THE e N EXHO- S YSTE M?
This operation will only be necessary when you are
installing the radiators. This conguration will re-
main saved even with electric cut outs.
It is necessary to go through this process in order
to be able to control your heating system from your
eNEXHO application.
In the eNEXHO application, select in your menu "Heating" and
press the option "Conguration". If your request for password
is not deactivated, the conguration password will be, by de-
fault, "nexho".
1. If this is the rst radiator you are installing in the zone:
› Select "Add Zone". Press the blank space where you can read
"Name" and introduce the name of the zone where the radiator is being located (or any name you want to give to that
radiator). Accept and wait until the zone is created.
› Select the option "Add modules"
› When the screen shows the message "Waiting for the modu-
le" select the following options from your LAVA®-R design
infrared heater: Menu -> Conguration -> Install
› If all this has been done correctly, in your applications screen
you should see that the number of modules installed has
changed from 0 to 1
› The heater is now ready to be controlled from your eNEXHO
application
2. If you want to install another radiator in an existing zone:
› Select "Edit Zone". Select the zone that you have previously
created where you want to install a second radiator
› Select the option "Add modules"
› When the screen shows the message "Waiting for the modu-
le" select the following options from your LAVA®-R design
infrared heater: Menu -> Conguration -> Install
› If all this has been done correctly, in your applications screen
you should see that the number of modules installed has in-
creased in one unit.
› The new heater is now ready to be controlled from your
eNEXHO application.
How to change the name of one heating zone?
In the eNEXHO application go into the "Heating" menu and
press the "Conguration" option. If your request for password
is not deactivated, , the conguration password will be, by de-
fault, "nexho".
Press over "Edit Zone" and select the zone you want to rename.
Click on the blank space where the previous name appears and
introduce the new name.
Keep in mind that, when changing the name of a
zone, this will affect to every module that has been
installed in that zone.
Use the +/- buttons to select the temperature you want and
then press the "Modify" button.
How to activate the programs in the LAVA®-R design infrared
heater?
In the eNEXHO application click on the "Heating" button and
click the option "Programs". Select the zone/room where you
want to activate the programs.
Please keep in mind that you can select more than one room/
zone in the upper part of the screen where it gives you several
options: "One Zone", "Various Zones" and/or "All Zones".
Now select the option "Activate Programs".
How to deactivate the programs in your LAVA®-R design infrared heater?
In the eNEXHO application click on the "Heating" button and
click the option "Programs". Select the zone/room where you
want to deactivate the programs.
Please keep in mind that you can select more than one room/
zone in the upper part of the screen where it gives you several
options: "One Zone", "Various Zones" and/or "All Zones".
Now select the option "Deactivate Programs".
How to personalize or modify the programs of your LAVA®-R
design infrared heater?
In the eNEXHO application click on the "Heating" button and
press the "Programs" option. Select the zones/rooms where
you want to personalize the programs. Please keep in mind
that you can select more than one room/zone in the upper part
of the screen where it gives you several options: "One Zone",
"Various Zones" and/or "All Zones".
Now select the option "Edit Programs".
Select the days you want to personalize the programs. Remember you can pick more than one day in the options "Various
days" or "All" in the menu you will nd in the upper part of the
screen.
Insert the time when you want the program to begin, the time
when you want the program to stop and the temperature in the
rst timeframe of the programming menu.
Add the time frames you need with the +/- buttons until you are
covered with the 24 period per day. (you can program up to 6
time frames).
In the lower part of the screen you will be able to see a graphic
bar in several colors, each color being the different timeframes
you have programmed.
Press the button "Save". The heater is now programmed.
How to change the temperature in the different rooms?
In the eNEXHO application click on the "Heating" button. Select the room/zone where you want to change the temperature.
Please keep in mind that you can select more than one room/
zone in the upper part of the screen where it gives you several
options: "One Zone", "Various Zones" and/or "All Zones".
28
How to install a LAVA®-R design infrared heater in a "repeater mode"?
Select the "Repeater" option on the "Conguration" menu and
choose either "Activate" or "Deactivate". If the function is already enabled only the "Deactivate" option will come up, and
vice versa.
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
With the new eNEXHO system, you will be able to control the
radiators that are out of the internet module range. Using the
built in repeater you will nd in our LAVA®-R design infrared
heaters, you will be able to send instructions to all the heaters,
even those far away from the module. Activate this command
only in the radiators that you may need and that are located
between the internet module and those where the signal does
not reach
You can set several heaters on a repeater mode, increasing si-
gnicantly the distance between the internet module and the
furthest heater.
› Approach a heater that is receiving the signal from the in-
ternet module, this one should be located near the heater
where the signal does not reach. Press the button CANCEL/
MENU.
› Press the button once, thus positioning the indicator "" in
front of "Conguration"
› Press the "OK" button
› Press the button 3 times, thus positioning the indicator ""
in front of "Repeater"
› Press the "OK" button
› Now the indicator "" will be positioned in front of "Activa-
te". Press the "OK" button. Now the radiator is working on
repeater mode. (Note: If when arriving to this step the indi-
cator "" is positioned in front of the "Deactivate" Word, this
would mean that the repeater mode was already active)
To deactivate the repeater mode in a heater please follow the
next steps:
› Go to a heater that correctly receives the signal/instructions
from the internet module and that is near another one that
does not receive the signal. Press the button CANCEL/MENU
once.
› Press the button once, thus positioning the indicator "" in
front of "Conguration"
› Press the "OK". button
› Press the button 3 times, thus positioning the indicator ""
in front of "Repeater"
› Press the "OK" button
› Now the indicator "" will be positioned in front of "Deac-
tivate". Press the "OK" button. Now the repeater mode is
deactivated. (Note: If when getting to this step the indicator
"" is positioned in front of the "Activate" word, this would
mean that the repeater mode has already been deactivated.
Only activate this function when necessary, and on
the smallest number of radiators possible. An excessive number of repeaters in the installation can give rise to
substantial delays in the system’s communications.
WORKING W I TH e N EXHO-CL THE RMOSTATS
How to install an eNEXHO-CL thermostat module in the automation
This operation will only be necessary when you are
installing thermostat modules. This conguration
will remain saved even with electric cut outs.
It is necessary to go through this process in order
to be able to control your thermostat modules from
your eNEXHO application.
In the eNEXHO application select the "Heating" menu and
press the option "Conguration". If you haven´t deactivated the
password request, this will be, by default, "nexho".
1. If this is the rst thermostat that you install in the zone:
› Select the option "Add Modules"
› When the screen shows the message "Waiting for the modu-
le" press the installation button from your Thermostat Module eNEXHO-CL.
› If all this has been done correctly, in your applications screen
you can see that the number of modules installed has changed from 0 to 1.
› The thermostat is now ready to be controlled from your
eNEXHO application..
2. If you want to install another thermostat in an existing zone:
› Select "Edit Zone". Select the zone that you have previously
created where you want to install a new thermostat
› Select the option "Add Modules"
› When the screen shows the message "Waiting for the modu-
le" press the installation button from your Thermostat Mo-
dule eNEXHO-CL
› If all this has been done correctly, in your applications screen
you can see that the number of modules installed has increased in one unit.
› The new thermostat is now ready to be controlled from your
eNEXHO application.
How to change a name of a thermostat zone?
In the eNEXHO application go into the "Heating" menu and
press the "Conguration" option. If your request for password
is not deactivated, , the conguration password will be, by de-
fault, "nexho".
Press over "Edit Zone" and select the zone you want to rename.
Click on the blank space where the previous name appears and
introduce the new name.
Keep in mind that, when changing the name of a
zone, this will affect to every module that has been
installed in that zone.
How to change the temperature in the different rooms?
In the eNEXHO application click on the "Heating" button. Select the room/zone where you want to change the temperature.
Please keep in mind that you can select more than one room/
zone in the upper part where it gives you several options: "One
Zone", "Various Zones" and/or "All Zones".
Use the +/- buttons to select the temperature you want and
then press the "Modify" button.
How to activate the programs in the thermostat modules
eNEXHO-CL?
In the eNEXHO application click on the "Heating" button and
click the option "Programs". Select the zone/room where you
29
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
want to activate the programs. Please keep in mind that you
can select more than one room/zone in the upper part where
it gives you several options: "One Zone", "Various Zones" and/
or "All Zones.
Now select the option "Activate Programs".
How to deactivate the programs in the thermostat modules
eNEXHO-CL?
In the eNEXHO application click on the "Heating" button and
click the option "Programs". Select the zone/room where you
want to deactivate the programs. Please keep in mind that you
can select more than one room/zone in the upper part where
it gives you several options: "One Zone", "Various Zones" and/
or "All Zones".
Now select the option "Deactivate Programs".
How to personalize or modify the programs of your thermostat
modules eNEXHO-CL?
In the eNEXHO application click on the "Heating" button and
press the "Programs" option. Select the zones/rooms where
you want to personalize the programs. Please keep in mind
that you can select more than one room/zone in the upper part
where it gives you several options: "One Zone", "Various Zones"
and/or "All Zones".
Now select the option "Edit Programs".
Select the days you want to personalize the programs. Remember you can pick more than one day in the options "Various
days" or "All" in the menu you will nd in the upper part of the
screen.
Insert the time that you want the program to begin, the time
when you want the program to stop and the temperature in the
rst timeframe of the programming menu.
Add the time frames you need with the +/- buttons until you
have covered the 24 period per day.
In the lower part of the screen you will be able to see a graphic
bar in several colors, each color being the different timeframes
you have programmed.
Press the button "Save". The thermostat is now programmed.
WORKING W I TH e N EXHO-PR P R E S E N CE DET ECTORS
How to install an eNEXHO-PR presence detector in the auto-
This operation will only be necessary when you are
installing presence detectors. This conguration will
remain saved even with electric cut outs.
It is necessary to go through this process in order to
be able to control your presence detectors from your
internet module.
mation network?
In the eNEXHO application select from the menu "Security
Systems" and press the "Conguration" option. If you have not
deactivated the password request, the security password is, by
default, "0000"
Select the option "Add new sensors" and select the type of sensor "Presence". Select the zone where you want to install the
new sensor. If you still have not created the zone, select the
option "Create Zone" and name it.
When the screen shows the "Waiting for the module" message,
press the installation button in the detector you want to install.
The sensor will now be ready to work in your automation system.
WORKING W I TH e N EXHO-IN FLOOD DET ECTORS
How to install an eNEXHO-IN ood detector in the automation
network?
This operation will only be necessary when you are
installing ood detectors. This conguration will re-
main saved even with electric cut outs.
It is necessary to go through this process in order
to be able to control your ood detectors from your
eNEXHO application.
In the eNEXHO application select from the menu "Security Systems" and press the "Conguration" option. If you have not deactivated the password request, the security password will be, by
default, "0000"
Select the option "Add new sensors" and select the type of sensor "Flooding". Select the zone where you want to install the new
sensor. If you still have not created the zone, select the option
"Create Zone" and name it.
When the screen shows the "Waiting for the module" message,
press the installation button in the detector you want to install.
30
The sensor will now be ready to work in your automation system.
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
WORKING W I TH e NEXHO-IC / HU FIRE- ODER SMOKE DETECTORS
How to install an eNEXHO-IC re detector or an eNEXHO-HU
smoke detector in the automation network?
This operation will only be necessary when you are
installing re- or smoke detectors. This congurati-
on will remain saved even with electric cut outs.
It is necessary to go through this process in order to
be able to control your re- or smoke detectors from
your eNEXHO application.
In the eNEXHO application select from the menu "Security Systems" and press the "Conguration" option. If you have not deactivated the password request, the security password will be, by
default,"0000"
Select the option "Add new sensors" and select the type of sensor "Fire". Select the zone where you want to install the new
sensor. If you still have not created the zone, select the option
"Create Zone" and name it.
When the screen shows the "Waiting for the module" message,
press the installation button in the detector
The sensor will now be ready to work in your automation system.
WORKING W I TH e N EXHO-NM NUME R IC REMOTE CONTROL
How to install an eNEXHO-NM numeric remote control in the
automation network?
This operation will only be necessary when you are
installing the numeric remote control. This congu-
ration will remain saved even with electric cut outs.
It is necessary to go through this process in order to
be able to control your numeric remote control from
your eNEXHO application.
deactivated the password request, the security password will
be, by default,"0000".
Select the option "Add new sensors" and select the type of sensor "Numeric". Select the zone where you want to install the
new sensor. If you still have not created the zone, select the
option "Create Zone" and name it.
When the screen shows the "Waiting for the module" message,
press the OK button in the module you want to install to turn it
on, and press it again until you hear a bip and in the application
screen you will see that it has been correctly installed.
In the eNEXHO application select from the menu "Security
Systems" and press the "Conguration" option. If you have not
The numeric module will now be ready to work in your automation system.
WORKING W I TH e N EXHO-CP POWE R C ONTROL MOD ULE S
How to install eNEXHO-CR power control modules in the automation network?
This operation will only be necessary when you are
installing power control modules. This conguration
will remain saved even with electric cut outs.
It is necessary to go through this process in order to
be able to control your power control modules from
your eNEXHO application.
In the NEXHO application select the "Other Equipment" menu
and press the option "Conguration". If you haven´t deactivated the password request, this will be by default "nexho".
If this is the rst thermostat that you install in the zone:
› Select "Add Zone". Press the blank space where you can
read "Name" and introduce the name of the zone where the
power control module is being located. Usually the name of
the zone will be the name of the electric product you want to
control with that module.
› Accept and wait until the zone is created.
› Select the option "Add Modules"
› While the screen shows the message "Waiting for the mo-
dule" press the installation button from your power control
module
› If all this has been done correctly, in your applications screen
you can see that the number of modules installed has changed from 0 to 1
› The power control module is now ready to be controlled from
your eNEXHO application
If you want to install another power control module in an existing zone:
› Select "Edit Zone". Select the zone that you have previously
created where you want to install a new thermostat
› Select the option "Add Modules"
› When the screen shows the message "Waiting for the mo-
dule" press the installation button from your power control
module
› If all this has been done correctly, in your applications screen
you can see that the number of modules installed has incre-
ased in one unit
› The new module is now ready to be controlled from your
eNEXHO application..
How to change a name of a power control module?
In the eNEXHO application go into the "Other Equipment" menu
and press the "Conguration" option. If your request for pass-
31
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
word is not deactivated, the conguration password, by default
will be, "nexho".
Press over "Edit Zone" and select the module you want to rename. Click on the blank space where the previous name appears
and introduce the new name.
Keep in mind that, when changing the name of a
zone, this will affect to every module that has been
installed in that zone.
How to delete a power control module from the list?
In the eNEXHO application, select the menu "Other Equip-
ments" and press the "Conguration" button. If your request
for password is not deactivated, the conguration password, by
default will be, "nexho".
Press the "Delete Zone" button and select the module you want
to delete.
How to activate/deactivate a power control module from your
application?
In the eNEXHO application click on the "Other Equipment"
button. Select the zone where you want to modify the working
condition. Remember that you can select more than one zone
with the options "Various Zones", "All" in the upper part of the
menu.
Press de sliding button to activate or deactivate the working
condition.
How to activate the programs in a power control module?
In the eNEXHO application click on the button "Other Equipment" button and press the option "Programs". Select the zone
where you want to activate the programs.
WORKING W I TH e N EXHO-IL L I GHTING MOD ULE S
How to install an eNEXHO-IL lighting module in the automation network?
› The new lighting module is now ready to be controlled from
your eNEXHO application.
This operation will only be necessary when you are
installing lighting modules. This conguration will
remain saved even with electric cut outs.
It is necessary to go through this process in order to
be able to control your lighting modules from your
eNEXHO application.
In the eNEXHO application select the "Lights" menu and press
the option "Conguration". If you haven´t deactivated the password request, this will be, by default, "nexho".
1. If this is the rst lighting module you install in the zone:
› Select "Add Zone". Press the blank space where you can read
"Name" and introduce the name of the zone where the lighting module is being located. Accept and wait until the zone
is created.
› Select the option "Add Modules"
› When the screen shows the message "Waiting for the modu-
le" press the installation button from your lighting module
› If all this has been done correctly, in your applications screen
you can see that the number of modules installed has chan-
ged from 0 to 1
› The lighting module is now ready to be controlled from your
eNEXHO application.
2. If you want to install another lighting module in an existing zone:
› Select "Edit Zone". Select the zone that you have previously
created where you want to install a new lighting module
› Select the option "Add Modules"
› When the screen shows the message "Waiting for the modu-
le" press the installation button from your lighting module
› If all this has been done correctly, in your applications screen
you can see that the number of modules installed has incre-
ased in one unit
How to delete a lighting module from the list?
In the eNEXHO application, select the menu "Lights" and press
the "Conguration" button. If your request for password is not
deactivated, the conguration password, by default, will be,
"nexho".
Press the "Delete Zone" button and select the module you want
to delete.
Keep in mind that, when changing the name of a
zone, this will affect to every module that has been
installed in that zone.
How to change light intensity in any given zone/room from the
eNEXHO application?
In the eNEXHO application select the menu "Lights". Select the
zone/room where you want to modify the light intensity. Remember you can select more than one room/zone in the upper
part where it gives you several options: "One Zone", "Various
Zones" and/or "All Zones".
Press the "100%" or "OFF" button to turn on or off the lights
in the selected zone. You can also press "+" or "-" followed by
"Modify" to select an intermediate percentage of lighting.
How to activate the programs in a lighting module?
In the eNEXHO application click on the "Lights" button and
click the option "Programs". Select the zone/room where you
want to activate the programs.
Please keep in mind that you can select more than one room/
zone in the upper part where it gives you several options: "One
Zone", "Various Zones" and/or "All Zones".
Now select the option "Activate Programs".
32
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
How to deactivate the programs in a lighting module?
In the eNEXHO application click on the "Lights" button and
click the option "Programs". Select the zone/room where you
want to deactivate the programs.
Please keep in mind that you can select more than one room/
zone in the upper part where it gives you several options: "One
Zone", "Various Zones" and/or "All Zones".
Now select the option "Deactivate Programs".
How to personalize the programs of your lighting modules?
In the eNEXHO application click on the "Light" button and
press the "Programs" option. Select the zones/rooms where
you want to personalize the programs. Please keep in mind
that you can select more than one room/zone in the upper part
where it gives you several options: "One Zone", "Various Zones"
and/or "All Zones".
WORKING W I TH e N EXHO-PS BLI N DS MOD ULE S
How to install an eNEXHO-PS blinds module in the automation
network?
This operation will only be necessary when you are
installing blinds modules. This conguration will re-
main saved even with electric cut outs.
Now select the option "Edit Programs".
Select the days you want to personalize the programs. Remember you can pick more than one day in the options "Various
days" or "All" in the menu you will nd in the upper part of the
screen.
Insert the time when you want the program to begin, the time
when you want the program to stop and the command for the
rst timeframe of the programming menu.
Add the time frames you need with the +/- buttons.
In the lower part of the screen you will be able to see a graphic
bar in several colors, each color being the different timeframes
you have programmed.
Press the button "Save". The lighting module is now programmed.
› If all this has been done correctly, in your applications screen
you can see that the number of modules installed has increased in one unit
› Press the manual button to close the blinds and keep it
pressed until the blinds are totally up and reach the end of
the reel previously installed. Then let go of the button.
› The new blinds module is now ready to be controlled from
your eNEXHO application.
It is necessary to go through this process in order
to be able to control your blinds modules from your
eNEXHO application.
In the eNEXHO application select the "Blinds" menu and press
the option "Conguration". If you haven´t deactivated the password request, this will by default "nexho".
1. If this is the rst blinds module you install in the zone:
› Please totally close the blinds, with the ends of the reel cord
correctly congured.
› Select "Add Zone". Press the blank space where you can read
"Name" and introduce the name of the zone where the blind
module is being located. Accept and wait until the zone is
created
› Select the option "Add Modules"
› When the screen shows the message "Waiting for the mo-
dule" press the installation button from your blinds module
› If all this has been done correctly, in your applications screen
you can see that the number of modules installed has chan-
ged from 0 to 1
› Press the manual button to close the blinds and keep it
pressed until the blinds are totally up and reach the end of
the reel previously installed. Then let go of the button.
› The blinds module is now ready to be controlled from your
eNEXHO application.
2. If you want to install another blinds module in an existing
zone:
› Please totally close the blinds with the ends of the reel cord
correctly congured.
› Select "Edit Zone". Select the zone that you have previously
created where you want to install a new blinds module
› Select the option "Add Modules"
› While the screen shows the message "Waiting for the mo-
dule" press the installation button from your blinds module
How to delete a blinds module from the list?
In the eNEXHO application, select the menu "Blinds" and press
the "Conguration" button. If your request for password is not
deactivated, conguration password, by default, will be "nex-
ho".
Press the "Delete Zone" button and select the module you want
to delete.
Keep in mind that, when changing the name of a
zone, this will affect to every module that has been
installed in that zone.
How to open and close a blind?
In the eNEXHO application select the menu "Blinds". Select the
zone/room where you want to modify the position of any given
blind. Remember you can select more than one room/zone in
the upper part where it gives you several options: "One Zone",
"Various Zones" and/or "All Zones".
Press the "100%" or "0%" button to open or close the blinds
in the selected zone. You can also press "+" or "-" followed by
"Modify" to select an intermediate percentage of blind opening.
How to activate the programs in a blinds module?
In the eNEXHO application click on the "Blinds" button and
click the option "Programs". Select the zone/room where you
want to activate the programs.
Please keep in mind that you can select more than one room/
zone in the upper part where it gives you several options: "One
Zone", "Various Zones" and/or "All Zones".
Now select the option "Activate Programs".
33
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
How to deactivate the programs in a blinds module?
In the eNEXHO application click on the "Blinds" button and
click the option "Programs". Select the zone/room where you
want to deactivate the programs.
Please keep in mind that you can select more than one room/
zone in the upper part where it gives you several options: "One
Zone", "Various Zones" and/or "All Zones".
Now select the option "Deactivate Programs".
How to personalize the programs of your blinds modules?
In the eNEXHO application click on the "Blind" button and
press the "Programs" option. Select the zones/rooms where
you want to personalize the programs. Please keep in mind
that you can select more than one room/zone in the upper part
where it gives you several options: "One Zone", "Various Zones"
and/or "All Zones".
Now select the option "Edit Programs".
C ONFI GURE THE S ECURI TY MODE
How to modify the security password
The security password, by default, is "0000".
To change the security password enter the "Conguration"
menu in the main screen (depending on the device you are
using it may appear as a tool icon or by pressing the menu in
the device). If your password request is not deactivated , the
conguration password, by default, is "nexho". Press the option
"Password" and select the option "Change the security password".
Select the days you want to personalize the programs. Remember you can pick more than one day in the options "Various
days" or "All" in the menu you will nd in the upper part of the
screen.
Establish the time and command of the rst timeframe in the
applications program menu.
Insert the time when you want the program to begin, the time
when you want the program to stop and the command for the
rst timeframe of the programming menu.
Add the time frames you need with the +/- buttons.
In the lower part of the screen you will be able to see a graphic
bar in several colors, each color being the different timeframes
you have programmed.
Press the button "Save". The blind module is now programmed.
› Select the "Conguration" menu in the opening screen of
your eNEXHO application in your mobile device or TABLET.
In some of this application versions it may appear as a tool
icon at the top left part of the screen. If this icon does not appear, press the "Menu" button in your terminal. A submenu
will come out, now select "Conguration". If your password
request is not deactivated, the conguration password, by
default, is "nexho".
Press now the "Notications" button and then press "Activate
Push Notications"
Introduce the old password and press "accept". Introduce the
new password and press "accept". Repeat the new password
and press again "accept".
The security password has been modied.
How to receive security alarms in your mobile device?
Thanks to the internet module eNEXHO-NT you can receive security messages in your mobile device free of charge through
"PUSH" notications.
To receive these notications you must fulll the following cri-
teria:
› You should own a device with the Apple IOS system or an AN-
DROID device with an active data account. Please check with
your phone company to know if you are already subscribed to
this data account or to contract it if you want to
› The Wi-Fi router where you have connected the internet mo-
dule eNEXHO-NT must be connected to the Internet.
Remember you can use different options to connect yourself to
the Internet, not only by cable or ADSL. Please check the op-
tions of your phone company to nd about the availability of 3G
Wi-Fi Routers as a wireless access to the Internet if your house
does not support any of the other systems.
Once you pass the previous prerequisites follow the next steps:
› Congure your router to allow connections from your termi-
nal from outside your house through Internet. To accomplish
this please check section "HOW TO CONTROL A eNEXHO INSTALLATION FROM OUTSIDE THE HOUSE THROUGH INTERNET" in this instruction manual.
The system is now ready to send security notications to your
device.
How to congure the actions that your system has to take
when receiving a potential security breach?
The internet module eNEXHO-NT allows you to select other
elements within the eNEXHO system so they can actuate independently, when receiving a notication with a potential security breach.
To do this, in the eNEXHO application select the "Scenes" menu
and press the option "Conguration". If your password request
is not deactivated the conguration password, by default, is
"nexho".
Select the option "Congure New Scenes" and in the new menu
select "Presence". If your password request is not deactivated
the conguration password, by default, is "0000".
Select the modules "Lights", "Blinds" and "Other Equipment"
if you want them to activate when an intrusion alarm occurs.
Example: You could select "Other Equipment", an "Alarm" and
"On". The system would activate the power control module
"Alarm" when this intrusion occurs.
You can congure your intrusion security scene with as many
devices as you wish and have installed.
Once you have nished, press the button "Save".
34
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
How to activate/deactivate your security mode against intrusions?
In the eNEXHO application go to the "Security Systems" menu.
Select the zone with intrusion sensors where you want to activate/deactivate the security mode. You can also select the option "Activate sensors in every zone".
Press the intrusion alarm activate/deactivate button in the selected zone. If you have not deactivated it, the security password, by default, is "0000".
Remember when activating the security system, you will have
around 45 seconds before the system is loaded, which will give
you enough time to leave the premises while the intrusion detector activates.
The system will also give you 15 seconds approx. before activating the security scene or before sending it to your mobile
device so you have time to disconnect the security system when
entering your house.
How to activate/deactivate your security mode against intrusions from the numeric module?
Press the ON button on the numeric module. Press the "0" di-
git followed by the security password that you have congured.
Now press "0" if you want to deactivate the security mode or
press "1" if you want to activate it.
How to congure the actions that your system has to take
when receiving a potential ooding alert?
The internet module eNEXHO-NT allows you to select other
elements within the eNEXHO system so they can actuate independently, when receiving a notication with a potential ooding alert.
To do this, in the eNEXHO application select the "Scenes"
menu and press the option "Conguration". ".If your password
request is not deactivated, the conguration password, by de-
fault, is "nexho".
You can congure your ooding detection scene with as many
devices as you wish and have installed.
Once you have nished, press the button "Save".
How to activate/deactivate the security mode against ooding?
In the eNEXHO application go to the "Security Systems" menu.
Select the zone with ooding detectors where you want to activate/deactivate the security mode.
Press the ooding detectors activate/deactivate button in the
selected zone. If you have not deactivated it, the security password, by default, is "0000".
How to congure the actions that your system has to take
when receiving a potential re alert?
The internet module eNEXHO-NT allows you to select other
elements within the eNEXHO system so they can actuate in-
dependently, when receiving a notication with a potential re
alert.
To do this, in the eNEXHO application select the "Scenes"
menu and press the option "Conguration". ".If your password
request is not deactivated, the conguration password, by de-
fault, is "nexho".
Select the option "Congure New Scenes" and in the new menu
select "Fire". ".If your password request is not deactivated, the
conguration password, by default, is "0000".
Select the modules "Lights", "Blinds" and "Other Equipment" if
you want them to activate when a ooding alarm occurs.
Example: You could select "Other Equipment", an "Alarm" and
"On". The system would activate the power control module
"Alarm" when this re occurs.
You can congure your re detection scene with as many de-
vices as you wish and have installed.
Select the option "Congure New Scenes" and in the new menu
select "Flooding". ".If your password request is not deactivated,
the security password, by default, is "0000".
Select the modules "Lights", "Blinds" and "Other Equipment" if
you want them to activate when a ooding alarm occurs.
Example: You could select "Other Equipment", an "Electrovalve
for cutting water supply" and "On". The system would activa-
te the power control module "Electrovalve" when this ooding
occurs.
Once you have nished, press the button "Save".
How to activate/deactivate the security mode against res?
In the eNEXHO application go to the "Security Systems" menu.
Select the zone with Fire or smoke detectors where you want to
activate/deactivate the security mode.
Press the ooding detectors activate/deactivate button in the
selected zone. If you have not deactivated it, the security password, by default, is "0000".
35
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
WORKING W I TH S CEN E S
What is a scene?
A scene is a group of orders to the system all under one name
that allow to, when activated, create a determined situation
when mixing several eNEXHO modules installed in your house.
Example: Lets imagine we create an scene called "MOVIE". We
can congure this scene so when we choose it, for example, the
blinds of the living room go down, the lights go down to a 30 %
of intensity, the heating goes up to 21 ºC and the power control
module connected to a Home Cinema goes on.
How to create a scene?
Select the menu "Scenes" and press the "Conguration" button. If your password request is not deactivated, the congura-
tion password, by default, is "nexho".
Select the option "Congure New Scenes" and in the next menu
select "General".
Click the white box in order to introduce the name you want to
give to this scene.
Select the modules "Lights", "Blinds" and "Other Equipment"
that you want to activate when you want to execute this scene.
Example: To create the scene "MOVIE" that we have previously
explained, introduce the name "MOVIE" in name conguration
box. Select "Heating", "living Room" area and choose 21 ºC.
After this select "Blinds", pick the "Living Room" and select
"0%". Finally go to "Other Equipment" in the menu, select
"Home Cinema" and make sure its "On".
Once you have nished press the "Save" button.
How to activate one scene?
Select the "Scenes" menu and pick the scene you want to activate.
Press the "Activate" button.
How to change a general or a security scene?
Select the "Scenes" menu and press the option "Congure".
If your password request is not deactivated, the conguration
password, by default, is "nexho".
Select the option "Edit congured scenes" and in the next menu
select the scene you would like to change.
Select now the actions you have already congured and that
you wish to eliminate and conrm its elimination.
If you want to add new actions to this scene, just do it normally
as if you were creating a new scene.
Once you have nished press the "Save" button.
How to delete a general or a security scene?
In the eNEXHO application, select the menu "Scenes" and press
the "Conguration" button. If your request for password is not
deactivated, the conguration password, by default, is "nexho".
Press the "Delete Congured Scenes" button. In the next menu
select the scene you want to delete con conrm its elimination.
You can congure your scene with as many modules you want
and have installed.
WORKING W I TH ASSOCIATI ONS
Why associate?
The internet module eNEXHO-NT allows you to associate different elements within your system, making some devices operate independently after receiving orders from other devices.
For example we can associate the lights from an area in your
house which would go on when the presence detector in that
area is working and detects movement. Another association
would be, at the same time the presence detector detects movement in the house, the radiators can go on and start working
at any given temperature.
How can we associate?
To associate the functioning of one device after the signal of
other device within the system, select the equipment (module)
you want to associate: "Lights", "Blinds", "Sockets", "Scenes"
or "Heating".
Press the "Conguration" button. If your request for password
is not deactivated, the conguration password, by default, is
"nexho".
Press the "Edit Zone" button and select the zone you want to
associate. The application will remain in a waiting mode until
you take the following step.
Press the installation button of one of the next modules you
can associate and you want to use as the starting point of the
association:
› eNEXHO-PR Presence detector
› eNEXHO-IC Fire detector / eNEXHO-HU Smoke detector
› eNEXHO-IN Flooding detector
› eNEXHO-MT Multifunction remote. We will then be able to
associate actions to any of the four available buttons
› eNEXHO-NM Numeric remote control. We will then be able to
associate actions to the existing buttons numbered from 1 to 9
› eNEXHO-PS Blind Modules. We can associate actions to the
two cabled Wall switches. The blinds module will now be
congured as an association element so you won´t be able to
control it from here as a normal blind module
› eNEXHO-CR Power control module. We can associate this to
a cabled wall switch. The power control module will now be
congured as an association element so you won´t be able to
control it from here as a normal power control module.
Select the action you want to happen when the signal of the activating element you have chosen activates. Depending on the
module you have chosen as starter of the association you can
then choose one, two, four or nine actions to associate. If the
equipment you have chosen has various switches, you will be
able to pick those you want to associate with this action
36
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
You can add several different associations to each equipment,
in the same switch or in other ones you have not used.
Depending on the element you have associated, the application
will ask you if you want to congure a delayed period of time.
If you pick this option, the equipment will activate during that
amount of time when receiving the activation signal, to then
revolve to its previous state.
How to make work during certain hours a day, an association
of light modules?
You can congure an association in a Lights zone so it only
Works for a few hours a day; for example you can associate
lights to a presence detector but you don’t want this to activate
during the day.
Remember that, if you program it for the times of the associations, you won´t be able to maintain any other program previously saved in the Lights Module and vice versa.
In the eNEXHO application, select the menu "Lights" and press
the option "Programs". Select the zone where you want to per-
sonalize the programs. Remember that you can select more
than one zone with the options "Various Zones", "All", from the
top part of the menu.
Now select the days you want to note the times of associations.
Remember that you can select more than one day in the options "Various days" or "All" in the top part of the menu
Introduce the starting time, ending time and the command for
the rst timeframe of the application program.
Add as many timeframes as you consider with the "+" and "-"
buttons.
In the lower part of the screen you will be able to see a graphic
bar in several colors, each color being the different timeframes
you have programmed.
Press the button "Save". The association time frames for the
Light module are now programmed.
37
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
TROUBLE SHOOTI NG
It has been impossible to connect with X of the X modules installed in X.
If, on sending an order by means of the eNEXHO application
a message comes up on screen that reads "It has not been
possible to communicate with X of the X installed equipments"
followed by a zone, the internet module was not able to communicate with one of the equipments in the area in question.
Possible causes are:
› One of the pieces of the equipment in this area has been dis-
connected. Reconnect it and try to send the message again.
› Check that all modules have been correctly installed in the
automation network. Select the type of equipment that is
giving you problems ("Heating", "Lights", "Blinds", …) and
press the option "Congure". If you don’t have deactivated
password request, the conguration password, by default, is
"nexho".
› Select "Edit Zone", select the zone that is giving you prob-
lems and check that the number of installed modules is the
same as the real number of modules installed in that area. If
the number does not match, delete the zone and reinstall the
modules that belong to that zone.
› Some of the modules could be too far away from the inter-
net module. Try if possible to locate the internet module in a
central part of the house so the distance with the modules is
the minimum possible. Check that the rest of the modules in
your house are connected. Due to legal restrictions, the range of the internet module is limited, therefore the possibility
exists that you have to use other equipments installed in the
middle to act as a repeater, such as the LAVA®-R design infrared heater, power control modules, lighting modules and/
or blinds modules. If you have any of these available keep all
of them connected.
"Impossible to connect with the internet module"
When starting up, the application does not connect with the internet module.
Possible causes are:
› The internet module is disconnected. Check that only the
green light of the internet module is on.
› The RJ45 cable is not correctly connecting the eNEXHO-NT
module with the router. Check that the red light is not on and
that the connection of the network cable and the router is
done through the "data out" port and not the "Data in"
› The router does not have internet connection and the device
with the eNEXHO application is not connected to the local
Wi-Fi.
› The router has internet connection, but the device with the
eNEXHO application is not connected to the local Wi-Fi and
does not have internet access.
› The device does have internet connection and the same goes
for the router, but it´s trying to connect to your house through
internet and you have not correctly congured the router to
connect outside the local network. Check the section HOW
TO CONTROL A eNEXHO INSTALLATION FROM OUTSIDE
YOUR HOUSE THROUGH INTERNET? in this manual.
38
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
T ECHNICAL DETAI LS
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 VAC (50-60 Hz)– 5 V (CC)
Operating voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3,3 V
Operating consumption ....................................40 mA
Max operating consumption ................................1A
CARE AND MAI NTE NANCE
The eNEXHO-NT does not need any special maintenance care. Only a few small instructions need to be followed as regards is
preservation:
› Clean the Remote’s casing with a slightly damp cloth.
› Do not use abrasive chemical products when cleaning the eNEXHO-NT.
WHEN TROUBLESHOOTING
PLEASE CONTACT THE CUSTOMER CARE OF YOUR SPECIALIST DEALER.
indicAtion: Subject to technical modications. Changes, errors and misprints shall not be entitled to compensation.
WArning: Electrical and electronic appliances often contain prescious materials. But they can also contain harmful substances that were
necessary for their function and safety. They can harm the environment if disposed or mishandled. Please help to protect our environment!
Therefore do not dispose of this device in the residual waste. Dispose of this unit in accordance with local regulations. Dispose of the packaging
materials, replacement parts or equipment parts properly.
39
ASSEMBLY A ND OPERA TING INSTRUCTIONS | e N EXHO-NT - H OME A UTOMA TION
GEN E RAL WARRANTY C ONDIT I ONS
Dear Customer,
please refer to our terms and conditions common paradigm. In warranty cases inform your dealer directely and he will help you
due to country-specic legal claims.
e N EXHO- NT
Distributed by:...............................................................................................
Purchase date: ........................................
FITTER: ....................................................................................................
Name: .....................................................................................................
Addresse: ..................................................................................................
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Telephone:............................................
USER:
Name: .....................................................................................................
Addresse: ..................................................................................................
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
In service: ............................................
No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ETHERMA
Elektrowärme GmbH
Landesstraße 16
A-5302 Henndorf
Tel.: +43 (0) 6214 | 76 77
Fax: +43 (0) 6214 | 76 66
Web: www.etherma.com
Mail: ofce@etherma.com
ETHERMA
Deutschland
Fabrikstraße 3
D-48599 Gronau
Stand: 10/2014
Tel.: +49 (0) 25 62 | 81 97 00
Fax: +49 (0) 25 62 | 81 62 90
Web: www.etherma.com
Mail: ofce.de@etherma.com
Loading...