ETERNITY G16, G20, G26 Installation And Operating Instructions Manual

aternit

hot water solutions

by

CHRIMSIEN

EXTERNAL GAS HOT WATER UNIT

INSTALLATION AND OPERATING

INSTRUCTIONS

MODELS G16/G20/G26

FOR ADVICE, REPAIRS AND

FAST SERVICE

1300 367 565



20501072(K)

INDEX

INSTALLATION INSTRUCTIONS

PAGE NO.

Introduction

1

Dimensions Connections

2

Exploded Diagram

3

Technical Data

4-5

Gas Connection

6

Cold Water Connection

7

Hot Water Connection

8

Electrical Requirements

8

Remote Controls

9

Remote Controls Wiring Diagram

10

Main Remote Control

11

Shower Remote Control

12

Mounting Remote Controls

13-14

User Instructions

15-17

Care of THE ETERNITY Hot Water Unit

18

Hints for Using THE ETERNITY Unit

19-23

Fault Monitor

24

Warranty Conditions

25

INTRODUCTION

ETERNITY G16/G20/G26

INSTALLATION INSTRUCTIONS

INTRODUCTION

The E I ERNTTY 16/20/26 is an external electronic gas hot water heater.
The ETERNITY 16/20/26 is supplied set at a constant 60°C outlet temperature

depending on the model purchased. Three optional remote controls can be
provided for complete hot water temperature selection and if this option is

used an approved temperature limiting device must be installed.

THIS HOT WATER UNIT IS NOT FOR

POOL OR SPA HEATING

GENERAL

1.0.1

The ETERNITY 16/20/26 must be installed in accordance with

(1)

These instructions;

(2)

Uniform Building Regulations Local authority regulations;

(3)

AS/NZS 3500.4"National Plumbing and Drainage Code, Part 4 Hot Water
Supply Systems",

(4)

The Australian Gas Association installation code AS5601 for gas burning

appliances and equipment;

(5)

Any other statutory regulation that may apply;

(6)

A notice of intention to install shall be lodged with the relevant Municipal

Authority and local Gas Authority prior to installation.

INSTALLATION MUST BE CARRIED OUT ONLY BY
AN AUTHORISED AND APPROPRIATELY LICENSED PERSON.

1.0.2
DELIVERY INSPECTION

The ETERNITY HOT WATER unit is supplied fully assembled for installation.
The customer or installer upon delivery of the unit should immediately remove all
packing materials and inspect the unit for damage and ensure that the unit supplied
is correct for the gas supply to which it is to be connected, report any damage or
discrepancies quoting to the supplier the serial number and model number, which
can be found on the outside of the cabinet.

1

CABLE ENTRY POINT
HOT WATER OUTLET

RP1/2/15

111M=1==All

PIFQ)

WATER INLET FILTER

GAS SUPPLY INLET

RP3/4/20

PRESSURE RELIEF VALVE

330

CABLE ENTRY POINT
HOT WATER OUTLET

RP3/4/20

10111===YAN

[

pi=

Cr 25:

WATER INLET FILTER

GAS SUPPLY INLET

RP3/4/20

COLD WATER INLET RP3/4/20

PRESSURE RELIEF VALVE

330

COLD WATER INLET RP1/2/15

12



165



15

Model : 16/20

Model : 26

DIMENSIONS CONNECTIONS

2

III

J

/

o0 igo

IN

MirMaCEMIVACIBil

-

11E111

U

I

a

0 0

NOS. PARTS DESCRIPTION

1 FLUE OUTLET
2 GAS VALVE
3 CIRCUIT BOARD
4 BURNER CASE
5 HOT WATER OUTLET
6 COLD WATER INLET
7 GAS SUPPLY INLET
8 HEAT EXCHANGER

NOS. PARTS DESCRIPTION

1 FLUE OUTLET
2 GAS VALVE
3 CIRCUIT BOARD
4 BURNER CASE
5 HOT WATER OUTLET
6 COLD WATER INLET
7 GAS SUPPLY INLET
8 HEAT EXCHANGER
9 WATER VOLUME

PROPORTIONAL VALVE

0

0

Model : 16/20

Model : 26

0

0

0

0

EXPLODED DIAGRAM



2

3

1.1 TECHNICAL DATA AND DIMENSIONS ETERNITY 16 / 20 / 26

Nominal hourly gas consumption MJ/h



MODEL 16 20 26

by proportional electronic gas control



MJ/h



125 160 200

Test point pressure



MODEL NG LP

Water heating capacity raised 40°C



MODEL 16 20 26
ML/M 10 12.5 16.25

Working pressure



Max 1200kPa

Gas injectors of the following size in mm



MODEL NG LPG MODEL NG LPG

are fitted for the approved gas types



16/20 1.35 1.35 mm 26



1.34 1.0mm



1.65 1.65 mm



1.65 1.2 mm

Input voltage single phase 50Hz



240V

Maximum output current



MODEL 16 20 26
Amp0.37 0.45 0.47

SAIG Approval certificate no.



MODEL 16/20 GSCS 20021

26 GSCS 20021

Inlet gas connection male thread



18mm

Cold water connection male thread



MODEL 16/20 13mm

26 18mm

Hot water connection male thread



MODEL 16/20 13mm

26 18mm

Relief valve pressure setting



14001cPa

Weight dry



MODEL 16/20 16kg

26 17kg

1.2 DATA PLATE

Left outside of cabinet

1.3 GAS TYPE

The temporary gas label is located on the cabinet top.
The label is the gas that this appliance is designed to operate with.

16
20
26

.40

.40

.56

.61

.68

.70

DO NOT OPERATE WITH ANY OTHER GAS TYPE.

TECHNICAL DATA

4

1.4

HEATER DIMENSIONS:



DEPTH

165mm
WIDTH 350mm
HEIGHT

575mm

1.5

WARNING LABELS

Located on the side of the cabinet.
PLEASE READ THESE LABELS CAREFULLY.

1.6

INSTALLATION POSITION

THIS HEATER IS APPROVED FOR OUTDOOR INSTALLATION
ONLY-IT IS NOT SUITABLE FOR INDOOR USE.

Refer AS5601 for clearance details for flue terminal.

In addition,ensure that the appliance installation position permits easy access for

maintenance and operation.

For further infomation,please refer to the Gas Fitting Regulations.

1.7 POSITION FOR INSTALLATION

The heater must be installed by using a fixing method sufficient to hold the weight of
the unit (see the technical sheet for dimensions of mounting brackets and positions).

TECHNICAL DATA

5

1.8 GAS CONNECTION

(1)

Fit a union to the water heater gas inlet for easy connection and removal. The thread
diameter is 18mm.
THIS DOES NOT INDICATE THE SIZE OF THE GAS SUPPLY

refer to AS5601

for

guidance on pipe sizing.

(2)

Fit an AGA approved isolating gas cock in the supply line adjacent to the water heater gas
connection.

(3)

Ensure that the supply pipe and the gas pressure regulator(LPG or NaturalGas) has
sufficient flow capacity for this and other appliances connected to the fitting line.

(4)

For LPG appliances ensure that gas cylinders are of sufficient size.The water heater alone

will require a regulator of 4KG per hour capacity.

(5)

Before connecting the appliance to the gas service purge any debris or air from the gas
service. Venting of purged gas shall be an area free of sources of ignition.

Close the isolating gas cock prior to connection of the appliance.

(6)

After connection check all joints for leaks with an approved leak tester.

Refer to

AS5601

Installation Code for pipe sizing details. For your assistance we have

included the following pipe sizing from

AS5601

for copper tube using Natural Gas.

NOMINAL PIPE

SIZE IN mm

STRAIGHT LENGTH OF

PIPE METRES

HOURLY RATE

IN MJ/h

13

4

43.0

18

4

82.2

20

4

142.0

25

4

313.0

THE ETERNITY 16/20/26 REQUIRES A MINIMUM OF 125/160/200 MJ/h FOR
THE CUSTOMER TO OBTAIN THE FULL PERFORMANCE BENEFIT.

SERVICE CALLS ARE CHARGEABLE FOR

UNITS WITH INCORRECT GAS PIPE SIZES.

GAS CONNECTION

6

COLD WATER CONNECTION

1.9 COLD WATER SUPPLY TO WATER HEATER

Refer to the Technical Sheet for the position of connections. Minimum of 13mm for model

16/20 and 18mm for model 26 copper tube should be connected to the appliance . The
WATER INLET connection are 13mm BSP for model 16/20 and 18mm BSP for model
26 and requires a union to allow for removal of the water heater. Pipe sizing from the
cold water supply should be sized according to local BY LAWS for water supply.

ISOLATING GATE VALVE or BALL VALVE
A GATE VALVE or BALL VALVE must be used on the cold water inlet to the water

heater. THIS REQUIREMENT IS AN AUSTRALIA WIDE REQUIREMENT UNDER
THE NATIONAL PLUMBING CODE.

IF THE ABOVE INSTRUCTION IS NOT CARRIED OUT ALL WARRANTIES ON THE
UNIT WILL BE VOIDED.

STOP TAPS OR COMBINATION STOP TAPS AND
NON-RETURN VALVES ARE NOT TO BE USED!

N.B. NO PRESSURE REDUCTION VALVE IS

REQUIRED UNLESS THE INLET WATER
PRESSURE EXCEEDS 1400kPa AT ANY TIME
OF THE DAY. EG

EARLY HOURS OF THE

MORNING.

HOT WATER CONNECTION

2.0 Refer to Technical Sheet for the position of connection. The outlet connection is 13mm
for model 16/20 and 18mm for model 26 male thread and requires an isolating union to
allow for removal of the unit.

2.1 Install the hot water supply line to the unit in a minimum of 13mm

for model

16/20 and 18mm for model 26

copper tube. for units set at 50°C this must be a

minimum of Four (4) Metres to the first outlet.

2.2 Keep the pipe lengths to a minimum and make sure that the pipework is well
insulated, as correct performance of the appliance is dependent on properly
insulated pipework.

2.3 DO NOT FIT ANY VALVES OR RESTRICTORS TO THE OUTLET OF

THE WATER HEATER.

2.4 DO NOT FIT ANY OBSTRUCTION TO THE PRESSURE RELIEF

LOCATED ON THE HOT WATER OUTLET CONNECTION.

2.5 After purging the air from the system using the hot water supply taps, remove

the water inlet strainer located on the cold water supply inlet connection.
Remove any debris from the filter and replace. When replacing the filter do not
over tighten the"O"ring seal.

ELECTRICAL REQUIREMENTS

3.0 The appliance is equipped with a three pinned earthed plug to be connected to
a 220-240V 50Hz power supply. The electrical rating of the appliance is

0.37/0.45/0.47Amp.for the ETERNITY 16/20/26

3.1 The appliance requires a 240V 50Hz weatherproof power outlet installed in a
protected position adjacent to the appliance.

3.3 IMPORTANT: The appliance should always be disconnected from the power
supply before any maintenance is carried out.

8

Refer to Technical Sheets

4.0 The ETERNITY 16/20/26 comes complete, with one, two or three remote control
panels, as optional extras.

ONE REMOTE CONTROLS SYSTEM

MODEL

CMR-154

MAIN CONTROLS

TWO OR THREE REMOTE

MODEL

CMR-154

MAIN CONTROLS

CONTROLS SYSTEM

MODEL

YST-84

SHOWER CONTROLS

MODEL

YST-84S

ENSUITE CONTROLS

4.1 These controls are to be fitted in the following locations:

* MAIN CONTROLS-kitchen or laundry
* SHOWER CONTROLS-main bathroom

IMPORTANT
DO NOT locate the remote controls where they may come into contact with water.
DO NOT position the remote controls in the vicinity of chemicals.
DO NOT position the remote controls over a cooker, grill oven or toaster.
DO NOT position the remote controls where materials may spill onto them.

4.2 MAIN REMOTE CONTROLS CMR-154
The main remote controls is fitted using the mounting holes in the rear of the casing.

Wiring is from the rear using the wiring hole provided in the casing.

4.3 SHOWER REMOTE CONTROLS YST-84 & ENSUITE REMOTE CONTROL YST-84S
These remote controls have a self adhesive backing plate which can be adhered to any

clean dry surface. These controls must also be wired from the rear, leave sufficient

wire for disconnection and removal.

4.4 CONNECTION OF WIRING TO THE ETERNITY

Remove the front cover from the unit.
Install the wiring to the ETERNITY 16/20/26 main unit using conduit or by concealing

the wires in the wall cavity.
Install the wiring into the cabinet through the wiring access adjacent to the power cable, see
the Technical Sheet.

4.5



Using the cable clamps provided on the plate adjacent to the terminal block attach the
wiring to the plate. Then attach the wires to the terminals for the remote controls. See wiring
diagram next page. Replace the front cover and connect the power plug.

4.6 COMMISSIONING AND TESTING
After completing the installation of the unit, turn the water, power and gas supplies on to the

unit.
CONTROLS OPERATION

Turn the main remote controls ON by pressing the ON/OFF switch on the controls to the
ON position.

The MAIN REMOTE CONTROLS will indicate the 42°C and the MAIN CONTROLS light
will be alight.

Using the UP/DOWN buttons select the hot water temperature required. Turn on the hot
water supply tap. The burner light glowing will indicate that hot water is being supplied.
Move to the shower controls (if fitted). Press the TRANSFER BUTTON and repeat the procedure.
Move to the En Suite controls (if fitted). Press the TRANSFER BUTTON and repeat the procedure.

THERE ARE NO MINOR ADJUSTMENTS THAT CAN BE MADE TO THE UNIT.

REMOTE CONTROLS

9

ORO.

IN

c-1

,[71•H,

a

TERMINALS FOR

REMOTE CONTROLS

CABLE CLAMP

-1aPj=f,

I

o

CABLE ENTRY PORT
REMOTE CONTROLS CABLE

ANTI-FREEZE HEATER

WIRING DIAGRAM OF PCB

TURN OFF POWER SUPPLY TO HOT WATER UNIT AND REMOVE
PLUG FROM POWER OUTLET BEFORE REMOVING FRONT COVER OF
HOT WATER UNIT.

WIRING FROM MAIN UNIT TO MAIN & SHOWER/SUB REMOTE
CONTROLS

MAIN CONTROL

SHOWER CONTROL

240volt POWER SUPPLY

SUB CONTROL

(ENSUITE)

1

REMOTE CONTROLS WIRING DIAGRAM

10

MAIN REMOTE CONTROL

CMR-154

16

f

ON

(I)

\

(

AL M

AM



17 1'

1 • 17 17 t

PMCILI•ULD

rr

j

4-1 Fi-1

U6FF

i(1.

:.:..

...

:

o

.....°:

t..



.1

KITCHEN

CMR- 154

?

TIME SET





I

dlArrEtrnott

mtealuttatettretcoarigit.*:

hat. artdb.mst

y

t, onvittnet.tere,pkatekter

0.16,1111,t7 frvadcorfrratewta

ts-o_

to el°

1 a

7
4

5

8

3

2

9

NOS.

CONTROL

FUNCTION

1

DIGITAL DISPLAY

INDICATES TEMPERATURE & TIME
ERROR CODE WHEN SAFETY DEVICE ON

2

TEMPERATURE CONTROL

ADJUSTS TEMPERATURE BETWEEN 37°C TO 75°C

3

TRANSFER INDICATOR

INDICATES THIS CONTROL HAS PRIORITY

(GREEN)

(CAN ADJUST TEMPERATURE ONLY WHEN)

THE INDICATOR IS ILLUMINATED

4

ON INDICATOR(GREEN) INDICATES POWER IS ON TO SYSTEM

5

ON/OFF SWITCH POWER SWITCH TO OPERATE THIS CONTROL

6

COMBUSTION LAMP(RED)

INDICATES A HOT WATER TAP IS BEING OPERATED

7

ALARM LAMP(RED)

FLASHES IN ABNORMAL CONDITION

8

TIME SETTING LAMP(GREEN)

INDICATES THAT THE TIME SETTING IS IN PROCESS

9

TIME SETTING SWITCH PUSHES WHEN SETTING THE TIME

MAIN REMOTE CONTROLS

11

SHOWER / SUB REMOTE CONTROLS

YST-84 /YST-84S

16

C

ALM

(.„

LA

[

AM

rf TI

PM

Li LI

•nrit

•

LI 11 Pt 1

Ell In

r---

,

. . .

TRANSFE1

11

nn

ILM

f:---

°11

BATHROOM

,

ON/OFF

YST-84

o....

O.:':

Fa sa-ery erd pew usg Ice areto rend



te.e.e.

Arremox

11.02.Mry cacd,,,:edetrk,i,
PM,. *arr.

xla

7

3-A

3

4
5

3-B
2

(ILLUSTRATION IS FOR YST-84)

NOS. CONTROL

1



DIGITAL DISPLAY

2 TEMPERATURE CONTROL

3 TRANSFER SWITCH

(GREEN)

3-A TRANSFER INDICATOR

(GREEN)

3-B TRANSFER INDICATOR

(GREEN "T" LAMP)

4



ON INDICATOR(GREEN)

5



ON/OFF SWITCH

6 COMBUSTION LAMP(RED)

7 ALARM LAMP(RED)

FUNCTION

INDICATES TEMPERATURE & TIME
ERROR CODE WHEN SAFETY DEVICE ON

ADJUSTS TEMPERATURE BETWEEN 37°C TO 48°C

PUSHES TO SET PRIORITY TO THIS CONTROL

INDICATES THIS CONTROL HAS PRIORITY

INDICATES THIS CONTROL HAS PRIORITY

INDICATES POWER IS ON TO SYSTEM

POWER SWITCH TO OPERATE THIS CONTROL

INDICATES A HOT WATER TAP IS BEING OPERATED

FLASHES IN ABNORMAL CONDITION

SHOWER/SUB REMOTE CONTROLS

12

MOUNTING AND WIRING OF REMOTE CONTROLS

4.7

REMOTE CONTROLS

OPEN THE CARTON BOX AND MAKE SURE TO CHECK FOLLOWING PARTS
PROVIDED.

•

MAIN CONTROLS MODEL CMR-154

,,,---

j-------------

V

01"

\--,_____

2PCS

2PCS

REMOTE CONTROLS WOOD SCREW

CURL PLUG

WIRING

•

SHOWER/SUB CONTROLS MODEL YST-84 / YST-84S

''''

1111'11

'11A

-.•-

c

r

2PCS

04"

2PCS

41111°

2PCS

REMOTE CONTROLS

WOOD SCREW

CURL PLUG

CONNECTOR

(C

:1D

---

4

‘-----__



_____,-,

WIRING CABLE CLAMP

MOUNTING REMOTE CONTROLS

13

FRONT COVER

WOOD SCREW

FRONT COVER

REMOTE CONTROL

METAL BRACKET

METAL BRACKET

ALTERNATIVES IN MOUNTING REMOTE CONTROLS

IN EITHER OF THE FOLLOWING TWO ALTERNATIVES, YOU ARE TO REMOVE METAL
BRACKET ATTACHED TO THE BACK OF EACH REMOTE BY SLIDING THE BRACKET
FIRMLY DOWN TILL IT IS RELEASED FROM THE NOTCH BY CLICK, THEN PULL IT

OUT.(MAIN CONTROL ONLY)
SINCE SHOWER/SUB CONTROLS WATERPROOFED, PLEASE INSTALL ON DIRECT

MOUNTING.

A. USING THE BRACKET (BEING REMOVED AS ABOVE) AS A FIXTURE:

(REFER THE DIAGRAM BELOW)

1.

FIX THE BRACKET TO THE WALL WITH WOOD SCREWS PROVIDED USING ANY
TWO HOLES OUT OF THE SIX HOLES PROVIDED TO THE BRACKET.

2.

FASTEN WIRING TO THE TERMINAL BLOCK.

3.

FIX THE REMOTE CONTROLS TO THE BRACKET CATCHING THREE NAILS OF THE
BRACKET THROUGH NOTCH AND THEN SLIDING FROM ABOVE FIRM UNTIL IT
CATCHES THE NOTCH IN THE BRACKET AND CLICKS.

B. DIRECT MOUNTING

(REFER THE DIAGRAM BELOW)

1. REMOVE THE FRONT COVER OF THE
CONTROLS USING SCREWDRIVER
CAREFULLY EASING THROUGH THREE
SLOTS IN TURN PROVIDED AT THE TOP
OF THE CONTROLS.

2.

FASTEN WIRING TO THE TERMINAL
BLOCK.(PLEASE SKIP THIS PROCESS IN
CASE OF SHOWER/SUB CONTROLS.)

3.

FIX THE REMOTE CONTROLS BASE BY
WOOD SCREWS PROVIDED THROUGH
TWO HOLES AT THE BOTH SIDE OF THE
BASE. THEN FIT THE FRONT COVER IN
PLACE.

14

ON

`4

27n

{I

V II



A

1]

ILTRAI7ER1

v

ON

2ui

A j

..w-

ON/OFF

USER INSTRUCTIONS

PLEASE HAND THIS HANDBOOK TO THE USER AFTER INSTALLATION.
INTRODUCTION:

You have selected the ETERNITY electronic gas hot water unit. The following instructions will
assist you to obtain the best performance from your ETERNITY unit.

OPERATION:
Up to three remote controls are able to be installed with your ETERNITY unit for complete
controls of your hot water.
Please note units without remote control will be set at 60°C or in the case of commercial units 75°C.

OPERATION OF MAIN REMOTE CONTROLS

PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS APPLIANCE.

1.

TURN ON THE ON/OFF SWITCH (REFER PG 11 OF THIS MANUAL).

2.

THE TEMPERATURE DISPLAY WILL ILLUMINATE AT 42°C.

3.

THE "T" AND ON INDICATORS WILL ILLUMINATE.

4.

SELECT HOT WATER TEMPERATURE BY PRESSING UP / DOWN BUTTONS ON THE

CONTROLS.

5.

TURN ON A HOT WATER TAP. COMBUSTION INDICATOR WILL ILLUMINATE AFTER
A SHORT DELAY, ON BOTH REMOTE CONTROLS. THESE INDICATORS WILL REMAIN
ILLUMINATED UNTIL THE HOT WATER TAP IS TURNED OFF.

• MAIN CONTROL



• SHOWER/SUB CONTROLS

6.

THE HOT WATER TEMPERATURE CAN BE ALTERED AT ANY TIME DURING THE

OPERATION BY USING THE UP/DOWN BUTTONS LOCATED ON

.

THE CONTROLS.

USER INSTRUCTIONS

15

OPERATION OF SHOWER / SUB REMOTE CONTROLS

The SHOWER/SUB CONTROLS overrides the operation of the main control.
Leave the operation switch on the MAIN CONTROL switched ON.

YST-84/84S SHOWER/SUB CONTROLS

1.

Press the ON/OFF button after opening the cover on the CONTROLS. See diagram 1 below.

2.

Press the TRANSFER BUTTON and the TRANSFER light will illuminate and the
TEMPERATURE DISPLAY will have 42°C displayed. Please refer to page 12 of this
handbook. See diagram 2 below.

3.

Using the UP/DOWN BUTTONS select the temperature required. See diagram 3 below.

4.When you have finished using the hot water supply press the TRANSFER BUTTON to return
the controls back to the MAIN CONTROL.

DIAGRAM 1



DIAGRAM 2

DIAGRAM 3

USER INSTRUCTIONS

16

HINTS FOR USING REMOTE CONTROLS

FOR SAFETY AND ENERGY SAVINGS

1.

Set the MAIN CONTROL to 42°C for normal household use and to prevent small children

from scalding.

2.

For the dishwasher set the MAIN CONTROL to 60°C or the temperature in the manufacturer's

instructions.

3.

For showering use settings between 37°C-39°C and no cold water will be needed to be mixed,

and if other hot or cold water taps are used the temperature will be maintained.

THE TEMPERATURE WILL INCREASE BY 1°C WITH EACH
PRESS OF THE UP/DOWN BUTTONS. THE TEMPERATURE
CAN BE ADJUSTED CONTINUOUSLY BY KEEPING
THE BUTTON PRESSED. OVER 50°C UP TO 75°C,
THE TEMPERATURE IS CONTROLLED BY 5-°C NOTCH.

PLEASE NOTE ABOVE 50°C SCALDING CAN OCCUR WITHIN SECONDS

4.

The MAIN REMOTE CONTROL is left switched on at all times for operation.

5.

The MAIN REMOTE CONTROL is left switched on at all times and then change can be made

to the operation temperature at any time during operation of hot water taps.

17

1.

2.

3.

DO NOT HANG WASHING OR OTHER MATERIALS ADJACENT TO THE UNIT.

DO NOT STORE INFLAMMABLE MATERIALS WITHIN 2 METERS OF THE UNIT.

DO NOT TOUCH THE FLUE OUTLET OF THE UNIT DURING OR IMMEDIATELY AFTER
OPERATION.

IF ANY GAS SMELL COMES FROM THE UNIT,

DO NOT USE NAKED FLAMES

TO TEST FOR GAS LEAKS.

TURN OFF THE GAS SUPPLY AND POWER AND CONTACT YOUR

GAS SUPPLY COMPANY.

6.

IF A POWER FAILURE OCCURS THE REMOTE CONTROLS WILL NOT FUNCTION AND

THE CHOFU UNIT WILL NOT SUPPLY HOT WATER UNTIL POWER IS RESTORED.

WHEN POWER IS RESTORED THE REMOTE CONTROLS WILL
RESET AT 42°C AS A SAFE TEMPERATURE.

PLEASE NOTE

4.

5.

CARE OF THE ETERNITY UNIT

18

Close

Prohibited

No Fire

POINTS NEEDED FOR YOUR SPECIAL ATTENTION

,L

Danger

NO INSTALLATION INDOORS

(May cause oxygen deficiency accident or incomplete combustion.)

The unit is outdoor installation type. Never install indoor
or in the bathroom. It will be extremely dangerous since it
will cause oxygen deficiency and incomplete combustion. Prohibited

,AWarning

WATCH FOR GAS LEAK

May cause fire.)

When gas leak is noticed, stop using the unit immediately and close the gas valve, then contact
the shop you bought the unit from or the gas supply company.

CONFIRM TYPE OF GAS AND POWER SUPPLY

(May cause incomplete combustion, explosive ignition or fire.)

0

Check

ETERNITY G16 EXTERNAL GAS WATER

HEATER

ETERNITY G20 EXTERNAL GAS WATER

HEATER

ETERNITY G26 EXTERNAL GAS WATER

HEATER

SAIL APPROVAL No.

GSCS20021

NAT.G

°

a

0

5

CAN

Safety 8

Certified

n54553

SAI Global

SAIG APPROVAL No.

GSCS20021

NAT.G

A

rmi

5

VeY,

GaS Safety

8

Certified

AS

4558

SAI Global

SAIL APPROVAL No.

GSCS20021

NAT.G

m

..
,
A

Gas Safely 8

Certified

As 4552

SA1 Global

INPUT



M1/11

OUTPUT



kW/M1

125

27.8

INPUT



M.1/11

OUTPUT



kW/h

160

365

INPUT



M.1/11

OUTPUT



kW/M1

200

94.4
TEST POINT PRESSURE HIGHkPa
TEST POINT PRESSURE LOWkPa

0.40

G103

TEST POINT PRESSURE HIGHkPa
TEST POINT PRESSURE LOW



kPa

0.56

0.103

TEST POINT PRESSURE HIGH



kPa

TEST POINT PRESSURE LOWkPa

0.68

0.118

GAS INJECTORS



rnrn

135/1.65

GAS INJECTORS



1,,r11

1.35,1.55

GAS INJECTORS



rnm

1.34/1.65

WEIGHT



kg

MAX WATER PRESSURE



kPa

ISO
1200

WEIGHT



kg

MAX WATER PRESSUREkPa

16.0
1200

WEIGHT



kg

MAX WATER PRESSUREkPa

17.0

1200

MIN. WATER PRESSUREkPa

260

KN. WATER PRESSUREkPa

260

MIN. WATER PRESSUREkPa

210
WATER HEATING CAPACITY 10.01/min RAISED
VOLTAGE 240 Volts-50Hz 0.37AMPS

400

WATER HEATING CAPACITY 1 2.51/min RAISED
VOLTAGE 240 Volts-SOHz 0.45AMPS

400

WATER HEATING CAPACITY 1 G251./min RAISED 400
VOLTAGE 240 Volts-50Hz 0.47AMPS

20541310

20541330

20541350

SERIAL No. SERIAL No.

SERIAL No.

Make sure to use the gas type as well as power supply (voltage/frequency) as indicated on the
RATING LABEL located on the cabinet side.
There are Natural Gas and Propane Gas on the GAS TYPE LABEL.

HINTS FOR USING THE ETERNITY UNIT

19

Warning

NO DISASSEMBLY, REPAIR OR

MODIFICATION
(May cause fire, electric shock or other

accidents.)

414

No Disassemble

r



0

,3

CJ

Do not dissemble or modify the units.
Never fail to ask professional assistance from
the dealer you have bought your unit from for
such a case as installation, removing, auxiliary
installation work or connection to the solar
units.

CAUTION FOR INFLAMMABLE
ITEMS
(May cause fire or explosion.)

4.1

C==

()

Do not place any inflammable items such as
gasoline or benzene nor use them around the
unit.Take special care.

O

L

Warning

Freeze Prevention.

This unit comes equipped with electric heaters that discourage the water heater from
frerzing.
To enable this freeze prevention system to operate there must be an electrical power
supply connected to the unit.
The freeze prevention devices will not operate if the electrical power source is not
connected.

Caution.

The electric heaters are installed inside the water heater only all External Hot and Cold
water supply pipes and fittings connected to the water heater should be properly insulated.

O

O

20

Close

Close

Pull

No wet hand

Warning

CAUTION TO PREVENT SCALDING

Check the water temperature by hand first before using shower.

MEASURE TO BE TAKEN IN CASE OF EMERGENCY

When there is an emergency such as earthquake or fire, apply following procedure.

1.

Close the hot water outlet.

2.

Close the gas valve and the main water valve.

3.

Turn off the main power.

However, in case of gas leakage, first close the
gas valve then wait for the leaked gas to disperse

then turn off the main power supply.

4.

Contact the dealer from whom you bought the unit.

Caution

21

Caution

DANGER OF WET HANDS



INSERT POWER PLUG PROPERLY INTO

(May cause electric shock.)



TERMINAL

Do not touch power plug with wet hands.
It is dangerous, because it can cause electric
shock.

Check the power plug for dust accumulation,
then properly insert to the power point.

DO NOT PULL POWER CORD

(May generate heat and cause fire.)

DO NOT USE POWER CORD
BUNDLED

(May generate heat and cause fire.)

Do not turn off the power plug by pulling the
cord. It may generate heat by wire breakage
then cause fire.

If the power supply cord is
damaged,it should be replaced
by a cord available from

ETERNITY Agents.

Never use power cord in a bundled condition.
It will cause heat generation and fire.

4•

Warning

Prohibited

Prohibited

Check

22

° 11_4_11

ON/Ofj

ON

v

A

J

'TRANSFER

Check

Caution

CONFIRM IGNITION, COMBUSTION AND EXTINCTION

Please always check ignition, combustion and extinction of the unit by the operation lamp of the
main or shower/sub remote controls.

DO NOT PUT WATER ON THE



DO NOT INSTALL NEAR ELECTRIC

REMOTE CONTROLS



APPLIANCES

(May cause failure.)

Check

Do not put water on the remote controls.



When installed near to TV or radio, it may cause

It will cause failure.



picture disturbance or sound disturbance.
Install away from those appliances.

Instant overflow voltage caused by lightn ng can Make sure to secure good enough space around
damage the electronic parts. Therefore, to

•

n off



the unit to ensure space necessary for checking

the main power when you have thunder.



and maintenance.

SECURE SERVICE SPACE

Check

MEASURE TO BE TAKEN FOR
LIGHTNING POSSIBILITY

(May cause failure.)

Pull

No wet hand

23

FAULT MONITOR

THE ETERNITY HOT WATER UNIT HAS A SELF DIAGNOSING FUNCTION FOR FAULTS.

When the unit does not operate correctly, an error code is displayed on the MAIN and SHOWER
remote controls TEMPERATURE DISPLAY INDICATOR.
The cause of the fault can be determined after checking the fault numbers display on the remote
control display.

DISPLAY

PROBLEM

REMEDY

11

GAS BURNER FAILS TO IGNITE.

CHECK GAS SUPPLY.

72

FALSE FLAME DETECTION. CALL SERVICE CENTRE.

12

LOSS OF COMBUSTION.

CHECK GAS SUPPLY AND
PRESSURE.

14

RESIDUAL FLAME SAFETY

CALL SERVICE CENTRE.

DEVICE.

32

THERMISTOR WIRE BREAKAGE. CALL SERVICE CENTRE.

61

COMBUSTION FAN FAILURE. CALL SERVICE CENTRE.

740

COMMUNICATION FAILURE

TURN OFF POWER AND TURN

750

BETWEEN REMOTE CONTROLS

ON AGAIN.

760

&

PCB.

PLEASE NOTE REPLACENT POWER CODE FOR THIS APPLIANCE CAN BE
OBTAINED FROM THE ETERNITY SERVICE DEPARTMENT TELEPHONE [phone].

PLEASE NOTE ONLY AUTHORISED PERSONS ARE TO PERFORM SERVICE WORK
ON THIS APPLIANCE FAILURE TO OBSERVE THIS CONDITION WILL VOID THE
WARRANTY AND COULD MAKE THE APPLIANCE UNSAFE.

SCHEDULED SERVICE PERIODS

This water heater requires scheduled maintenance at regular 12 monthly periods to obtain the

maximum service life and safe operation.

FAULT MONITOR

24

Eternity Continuous Flow

1.

All Eternity water heaters must be installed by a Licensed installer.

2.

Only Authorised personnel must Install, Commission or Service Eternity water
heaters.

3.

All Eternity water heaters must be installed in accordance with Manufacturer's
Installation Instructions and in Accordance with local regulations, municipal
building codes and current AS/NZS3000, AS/NZS3500, AS 3498 and AS5601.

4.

If the Eternity water heater has not been installed in accordance with
Manufacturer's Installation Instructions or installed as to be easily accessable for
servicing, a service charge may apply.

5.

Where a component may have failed under warranty and is replaced, the
component replaced will only be covered by the warranty for the balance of
the appliance warranty period.

6.

Water Quality must be within limits specified in table below.

pH

Sodium

T

(Total DSDissolved

Solids)

Chlorides

Iron

Magnesium

Alkalinity

(as CaCO3)

Dissolved

(free) CO2

Tot

Hardne

al

ss

CaCO3

6.5

to

8.5

Up

to

150

mg/litre

Or

ppm

Up to

600

mg/litre

or

ppm

Up to 300

mg/litre

or

ppm

Up to 1

mg/litre

or

ppm

Up to 10

mg/litre

or

ppm

Up to

200

mg/litre

or

ppm

Up to

25

mg/litre

or

ppm

Up to

200

mg/litre

or

ppm

The warranty will be rendered void in the following circumstances:

1.

Failure due to misuse, Acts of God, accidental damage, installation by an

installer who is not unauthorised to install an Eternity water heater or incorrect
installation and attempts to repair Eternity by an unqualified person.

2.

Repairs and service carried out by a person who is not a Qualified Service Person

or Authorised Service Agent.

3.

Faults caused by incorrect installation, water problems, electricity supply and or

gas supply.

The warranty does not cover the following:

4.

Subject to any statutory provisions to the contrary, claims for damages to walls,
foundations etc or any other consequential loss caused either directly or
indirectly by leakage from the water heater or any other faults.

5.

Warranty does not cover any faults that may arise from connecting to a water

source that is unfiltered such as dams, bores, rivers etc.

Eternity does not accept liability for consequential damage or any incidental expenses
resulting from any breach of the Warranty.

WARRANTY CONDITIONS

25

Warranty Terms

Eternity Water Heaters are covered by Eternity for any cost of labour and parts in the
event of a component failure due to any defects that may arise either from
workmanship and or faulty material.

The Warranty commences on the date of Installation:

Domestic Appliance

Eternity Product

Heat Exchanger

Parts

10 Years

Labour

3 Years

All Other Parts

.



Parts

3 Years

Labour

3 Years

Commercial Application

Eternity Product

Heat Exchanger

Parts

5 Years

Labour

1 Year

All Other Parts

Parts 1 Year

Labour

1 Year

Definition of Domestic Use:

1.

Units installed in any domestic dwelling.

2.

Units installed in any gas boosted solar system in a domestic dwelling.

3.

Units used in any household applications.

Definition of Commercial Use:

1.

Units supplying kitchen areas used for bulk food preparation.

2.

Units used in industrial or bulk heating processors and hydronic heating installations.

3.

Units used as bulk central heating systems and flow and return systems.

Please contact your ETERNITY office for full warranty conditions

On 1300 367 565 for all Warranty and Service information.