Eternal Lighting CUBE5 User Manual

CUBE5™ RGBWA LED User

Manual

(Battery Powered DMX LED Fixture)

Please read over this manual before operating the light.

2

FIRST CHARGE YOUR FIXTURE FOR 6 HOURS.

Introduction

Unpacking: Thank you for purchasing the CUBE4™ RGBW QUAD LED. Every CUBE5™
RGBWA LED has been thoroughly tested and has been shipped in perfect operating
condition. Carefully check the shipping carton for damage that may have occurred during
shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage
and be sure all accessories necessary to operate the unit has arrived intact. In the case
damage has been found or parts are missing, please contact the manufacturer or your
dealer for further instructions. Do not return this unit to your dealer without first contacting.

Introduction: The CUBE5™ RGBWA LED is a DMX intelligent LED par light. This par light
is lightweight and compact which makes it a great piece for mobile DJ’s and clubs.

Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to
rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself; doing so will void your manufactures warranty. In the unlikely event your unit may
require service please contact the manufacturer or your dealer.

PLEASE recycle the shipping carton whenever possible.
General Instructions

To optimize the performance of this product, please read these operating instructions
carefully to familiarize you with the basic operations of this unit. These instructions contain
important safety information regarding the use and maintenance of this unit. Please keep
this manual with the unit, for future reference.

Features

 Multi-colors
 Control Channels:4CH & 8CH
 Color Strobe
 Master/Slave synchronization
 DMX-512 protocol
 Electronic Dimming 0-100%
 Operating Modes: Sound activation, Auto and DMX control mode
 Led operation menu with function buttons
 Daisy Chain Units Together in DMX Mode
 1-20 flashes/sec strobe effect

3

Safety Precautions

● To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

● Do not spill water or other liquids into or on to your unit.

● Be sure that the local power outlet match that of the required voltage for your unit.

● Do not attempt to operate this unit if the power cord has been frayed or broken. Do not

attempt to remove or break off the ground prong from the electrical cord. This prong is used
to reduce the risk of electrical shock and fire in case of an internal short.

● Disconnect from main power before making any type of connection.

● Do not remove the cover under any conditions. There are no user serviceable parts

inside.

● Never operate this unit when it’s cover is removed.

● Never plug this unit in to a dimmer pack.

● Always be sure to mount this unit in an area that will allow proper ventilation. Allow

about 6” (15cm) between this device and a wall.

● Do not attempt to operate this unit, if it becomes damaged.

● This unit is intended for indoor use only; use of this product outdoors voids all

warranties.

● During long periods of non-use, disconnect the unit’s main power.

● Always mount this unit in safe and stable matter.

● Power-supply cords should be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying particular attention to the point they
exit from the unit.

● Cleaning -The fixture should be cleaned only as recommended by the manufacturer.
See “Cleaning” for details.

● Heat -The appliance should be situated away from heat sources such as radiators, heat
registers, stoves, or other appliances (including amplifiers) that produce heat.

● The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in
performance

● Fuse standard is2A/250V

● Grounded using yellow/green line

● The ambient temperature must always be under +35° C

Set Up
Power Supply: Before plugging your unit in, be sure the source voltage in your area

matches the required voltage for your CUBE4™ RGBW QUAD LED. The CUBE5™ RGBWA

4

LED is workable in 100-220V/50~60Hz. Because line voltage may vary from venue to venue,
you should be sure your unit voltage matches the wall outlet voltage before attempting to
operate you fixture.

DMX Linking: To ensure proper DMX data transmission, when using several DMX fixtures
try to use the shortest cable path possible. The order in which fixtures are connected in a
DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX
address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or
anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller
knows to send DATA assigned to address 1 to that unit, no matter where it is located in the
DMX chain.

Operating Instructions

Operating Modes: You can use the CUBE5™ RGBWA LED in 4 ways:

● Sound activation – The unit will activated by the sound signal.

● Static display – The unit will display the pattern in static way.

● Auto Mode - The unit will automatically chase through the different patterns.

● DMX control mode - This function will allow you to control each individual fixtures traits

with a standard DMX 512 controller.
DMX Mode: Operating through a DMX controller give the user the freedom to create their

own programs tailored to their own individual needs. This function also allows you to use
your fixtures as pattern changing lights.

1. This function will allow you to control each individual fixture’s traits with a standard DMX

512 controller.

2. The Mini PAR uses 6 DMX channels to operate. Please see “DMX Values and Functions”
for the DMX traits.

3. To run your fixture in DMX mode, plug in the fixture via the XLR connections to any
standard DMX controller . Set your desired DMX address following the set up
specifications that come with your DMX controller .

4. The unit can automatically recognize the DMX signal once the DMX connection is done.