Eterna Lighting PIRHL60BK Installation Instructions

874/2012

MODELNO.

PIRHL60 Range

SPECIFICATIONS:

• Detection range: Approx. 120° (horizontal),
Max. 12 metres.

• Duration time: from 3 min ± 20 sec.

• Factory preset PIR - no override facilit y.

CLEANING:

To avoid dust build-up and ensure proper
functioning of the half lantern light, please wipe the
sensor lens lightly with a damp cloth every 3 months.

Disconnec t the power and clean the exterior only of
this tting with a moist (not wet) cloth.

Do not use any chemical or abrasive cleaners.

EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:

Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.

WHEN YOUR PRODUC T COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.

INSTALLATION INSTRUCTIONS

A guide for qualied electricians

LAMP REPLACEMENT:

• Switch o the electricity at the mains.

• Release front diuser cover with screwdriver.

• Remove and replace lamp making sure it seats
correctly in the lampholder.

• Replace front diuser cover.

• Restore power.

REPLACEMENT LAMP TYPE:

Requires 1 x suitable ES energy saving lamp (not
included).

Fitting is rated at 60W max.

Issue 2013

FOR PRODUCT ADVICE:

• T: 01933 673 144

• F: 01933 678 083

• E: [e-mail]

IF YOU EXPERIENCE PROBLEMS:

If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.

Visit our website:

www.eterna-lighting.co.uk

Pack contents:

• Half lantern with 120º PIR

Model:

• Mounting xtures

PIRHL60BK / PIRHL60WH

Half Lantern with 120° PIR

These instructions are provided as a guideline to assist you.

PLEASE READ THESE INSTRUCTIONS BEFORE USING YOUR NEW FITTING

PLEASE RETAIN FOR FUTURE REFERENCE

INTRODUCTION:

L

Brown
(power cable)

Rubber
Grommet

Plastic
Cover

Blue
(power cable)

N

Fixing Wall
Screw

1.8-2.5M

4M 8M 12M

120˚

Appr.

PIR
Sensor

L

Brown
(power cable)

Rubber
Grommet

Plastic
Cover

Lamp
Holder

Fixing Wall
Screw

Blue
(power cable)

N

Fixing Wall
Screw

Front
Housing

L

Brown
(power cable)

Rubber
Grommet

Plastic
Cover

Lamp
Holder

Fixing Wall
Screw

Blue
(power cable)

N

The half lantern incorporates a PIR (passive Infrared)
sensing device which continuously scans a preset
operating zone and immediately switches the light
on when it detects movement in that area.

This means that whenever movement is detected
within the range of the sensor the light will switch
on automatically to illuminate the area you have
selected to light. While there is movement within
range of the unit the light will remain on.

READ THIS FIRST:

Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.

This product must be installed by a competent
person in accordance with the current building
and IEE wiring regulations.

As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this t ting
is t for the purpose for which you have intended
it. Eterna lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.

This product is designed and constructed according
to the principles of the appropriate British Standard
and is intended for normal domestic ser vice. Using
this tting in any other environments may result in a
shortened working life.

Switch o the mains before commencing installation
and remove the appropriate circuit fuse or lock o
MCB.

This unit is suitable for outdoor use.

This product is designed for permanent connection
to xed wiring: this must be a suitable circuit
(protected with the appropriate MCB or fuse).

Before making xing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.

Make sure that the xings are strong enough to
support the considerable weight of the tting and
hold it rigidly.

The lamp must be positioned so that there is at least

0.5m (500mm) between the bulb and any illuminated
surface.

When making connections ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation.

WARNING: This prodct becomes hot!

This product is not intended to be used by children
and persons with sensory, physical and/or mental
impairments that would prevent them from using it
saf ely.

IMPORTANT - Always switch o the mains power
before changing the lamp.

You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out,
these tests are specied in the current IEE wiring and
building regulations.

This product is double insulated, do not connect any
part to ear th.

WHERE TO FIT YOUR PIR HALF LANTERN:

To achieve best results we suggest you take the
following points into consideration:

Do not mount on a surface that has vibration.

Ideally the PIR half lantern should be mounted 1.8
to 2.5 metres (6 to 8ft) above the area to be scanned
(refer to Fig. 1 below).

Fig 1

120˚

1.8-2.5M

To avoid damage to the unit do not aim sensor
towards the sun.

Avoid positioning the sensor unit adjacent to a
bright light source which may prevent the unit from
operating when the lux control is set to operate in
dark conditions.

Avoid nuisance false triggering by directing sensor
away from:

Trees and shrubs
Reective surfaces such as smooth white walls
Swimming pools
Heat sources such as boiler ues

The PIR sensor scanning specications
(approximately 12 metres at 120°) may vary slightly
depending on the mounting height and location.

4M 8M 12M

Appr.

The detection range of the unit may also alter
with temperature change. Before selecting a place
to install your PIR lantern you should note that
movement across the scan area is more eective
than movement directly towards or away from the
sensor (refer to Fig. 2 below).

If movement is made walking directly towards or
away from the sensor and not across the apparent
detection range will be substantially reduced (refer
to Fig. 3 below).

Fig 2 Fig 3

EFFECTIVE

LESS EFFECTIVE

Fig 4

Front
Housing

PIR
Sensor

INSTALLATION:

Please refer to Fig. 4 below.

1) Remove the two screws at the top and bot tom of
the tting and lift o the front housing.

2) Position the tting on the sur face where it is to be
installed and mark the mounting hole positions.

3) Drill and plug the wall at the marked positions
ensuring you pass the cable wire through rubber
grommet.

4) Screw and x the back housing to wall with
suitable mounting screws (supplied).

5) Remove PIR terminal cover and expose the
connector block and make connections according
to the relatives symbols:

(L) Brown wire
(N) Blue wire.

Make sure that terminals are tightened securely and
that no strands of wire protrude.

6) Replace and secure the plastic PIR cover.

7) Insert suitable ES energy saving lamp.

8) Replace the front housing and tighten the screws.

9) Restore the power and switch on.

Fixing Wall
Screw

Lamp
Holder

Plastic
Cover

Rubber
Grommet

Brown

L

(power cable)

Blue

N

(power cable)

Fixing Wall
Screw