Eterna Lighting L60B Installation Instructions

CLEANING:

Clean this light tting only with a soft dry cloth.

Do not use any chemical or abrasive cleaners.

LAMP REPLACEMENT:

• Switch o the electricity at the mains.

• Release top cover by removing the two screws.

• Remove and replace lamp making sure it seats
correctly in the lampholder.

• Replace and secure cover.

• Restore power.

REPLACEMENT LAMP TYPE:

Requires 1 x suitable ES energy saving lamp.

Wattage: Fitting is rated at 60W max.
Supply Voltage: 230V
Typ e: E27

Note: do not t reector lamps (spotlight or crown
reector).

EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:

Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd Januar y 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.

WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPL ACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.

IF YOU EXPERIENCE PROBLEMS:

If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.

874/2012

MODELNO.

L60B / WH

INSTALLATION INSTRUCTIONS

A guide for qualied electricians

Pack contents:

1 x Full lantern
1 x Fixing kit

Model:

Issue 2013

FOR PRODUCT ADVICE:

• T: 01933 673 144

• F: 01933 678 083

• E: [e-mail]

Visit our website:

www.eterna-lighting.co.uk

L60B / L60WH

Full Lantern

These instructions are provided as a guideline to assist you.

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION

AND RETAIN FOR FUTURE REFERENCE

READ THIS FIRST:

Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.

This product must be installed by a competent
person in accordance with the current building and
IEE wiring regulations.

As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this tting
is t for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.

The lifetime of compact uorescent lamps and
ballasts are negatively aected by increased
switching i.e. where a PIR is being used to control the
tting.

Switch o the mains before commencing installation
and remove the appropriate circuit fuse or lock o
MCB.

This unit is suitable for outdoor use.

This product is designed for permanent connection
to xed wiring: this must be a suitable circuit
(protected with the appropriate MCB or fuse).

Before making xing hole(s), check that there are no
obstructions hidden beneath the mounting sur face
such as pipes or cables.

Make sure that the xings are strong enough to
support the weight of the tting and hold it rigidly.

The chosen location of your tting should allow for
the product to be securely mounted and anchored to
a solid surface e.g. concrete, brick or a joist—do not
x directly onto panelling, cladding, plasterboard
etc.

This tting is double insulated; do not connect any
part to ear th.

Make connections to the electrical supply in
accordance with the following code:

Live: Brown or Red
Neutral: Blue or Black

When working at heights ensure you use a suitable
platform.

When making connections ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation.

WARNING: This product becomes hot!

This product is not intended to be used by children
and persons with sensory, physical and/or mental
impairments that would prevent them from using it
saf ely.

You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out,
these tests are specied in the current IEE wiring and
building regulations.

INSTALLATION:

For the below instructions, please refer to the
diagram on the opposite page.

01) Remove the two screws near to the top of the
transparent panels and lift o the top cover.

02) Remove the two nuts on the front of the wall
bracket and remove the plastic back-plate.

03) Using the back-plate as a template, mark the
location of the xing holes.

04) Pierce the rubber grommet in the back-plate and

thread the supply cable through. Take care not to
make the hole too large so that the grommet ts
tight around the cable and the waterproof seal is
maintained.

05) Secure the back-plate to the mounting surface
using the xings supplied. If the xings supplied
are not appropriate to your installation, select
suitable alternatives.

06) Make the electrical connections according to the

wiring code as shown.

07) Locate the t ting on the t wo screws protruding
from the back-plate and secure in position using
the two nuts - see opposite. Take care to position
the tting correctly onto the soft gasket.

08) Fit a suitable ES energy saving lamp.

09) Re-t the top of the tting tightening the screws

securely but take care not to overtighten.

10) Restore the power and switch on.

Brown

(Power Cable)

L

Blue

(Power Cable)

N

Cable

Terminal Block

Fixing Wall

Clamp

Screw

Power Cable (2 Core)

Rubber

Grommet

Wall

Screw

Fixing

L

Rubber

Gasket

N

Lid

Screw

x2

Fixing

Wiring

Fixing

Wall

Box

Nuts x2

Screw

Lid

Lantern

Lens

Lampholder

Transparent