EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUC T COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
INDUSTRIAL BATTERIES:
Within certain produc ts Eterna Lighting Ltd places
lead acid, lithium ion, nickel cadmium & nickel
metal hydride batteries on the market. Industrial
batteries are subject to waste regulation under
the Waste Batteries and Accumulators Regulations
2009 and should be disposed of responsibly.
Purchasers may be able to dispose of their waste
industrial batteries locally via legitimate licensed
trade waste contractors. Eterna is obliged to take
back, free of charge and within a reasonable time,
waste industrial batteries of the same chemistry
supplied to a Purchaser, for treatment and recycling
and is required to do this in any calendar year new
industrial batteries are placed on the market. In
certain circumstances, this may include batteries
not originally supplied by Eterna. If any Purchaser
requires Eterna to take back Industrial batteries,
they should write to the Operations Director, Eterna
Lighting Ltd, Huxley Close, NN8 6AB, who will then
advise on the necessary arrangements for the
receipt, proper treatment and recycling of, the waste
industrial batteries.
CLEANING:
Clean this tting only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.
Email: sales@eterna-lighting.co.uk / technical@eterna-lighting.co.uk
Visit our website: www.eterna-lighting.co.uk
BATTERY REPLACEMENT:
If after routine operational check, the lamp does not
remain lit for three hour period, a new bat tery pack
may be required.
01) Switch o the electricity at the mains.
02) Allow batteries to fully discharge then reconnect
to supply and allow to charge for 24 hours.
03) Test again for 3 hours, if light does not remain lit
change the battery pack as follows:
04) To replace the battery pack, it is necessary to
disconnect the tting from the mains supply and
lock o.
05) Remove the ceiling box cover.
06) Unplug the battery lead from the circuit board.
07) Unclip and remove the batter y pack.
08) Write current date on the new battery pack.
09) Secure the new battery pack in place.
10) Plug battery pack into circuit board.
12) Replace housing cover.
13) Restore power and allow charging for 24 hours.
14) Perform full operation check and update test
record.
REPLACEMENT BATTERY TYPE:
3.6v 800mAh Ni–cad
SPECIFICATION:
Rated wattage: 2.8W
Continuous illumination emergency: 3 hours
Battery: 3.6v 800mAh Ni-Cd
Recharge time: 24 hours
Over – discharge protection: Yes
Viewing distance: 30m
Made in ChinaIssue 0818
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
EXITMMO pack contents:
1 x Fitting
EXITREC: recessed
mounting kit
1 x Legend (up arrow exit)
1 x Suspension kit
1 x Wall mounting kit
1 x Maintenance check record
Model:
EXITMMO / EXITREC
LED Multi Fixing Emergency Exit Sign
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
READ THIS FIRST:
DANGER!
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not, contact
the outlet where you bought this product.
This product must be installed by a competent
person in accordance with the current building and
IEE wiring regulations.
As the buyer, installer and/or user of this product it is
your own responsibility to ensure that this tting is t
for the purpose for which you have intended it. Eterna
Lighting cannot accept any liability for loss, damage
or premature failure resulting from inappropriate use.
Switch o the mains before commencing installation
and remove the appropriate circuit fuse or lock o
MCB.
The batteries supplied with this tting are
consumable parts and therefore may be outside of
any warranty oered.
This unit is suitable for indoor use only.
This product is designed for permanent connection
to xed wiring: this must be a suitable circuit
(protected with the appropriate MCB or fuse).
Before making xing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.
The chosen location of your new tting should
allow for the product to be securely mounted (e.g.
to a ceiling joist) and safely connected to the mains
supply (lighting circuit).
Do not attach to surfaces which are damp, freshly
painted or otherwise electrically conductive (e.g.
metallic surfaces).
When making connections ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened onto
the bared conductors and not onto any insulation.
This product must be connected to Earth
termination.
This product is not intended to be used by children
and persons with sensory, physical and/or mental
impairments that would prevent them from using it
saf ely.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out,
these tests are specied in the current IEE wiring and
building regulations.
INSTALLATION:
01) Remove the screw at the end of the housing and
unclip the top cover.
02) Use the rear of the case as a template, mark the
position of the xing holes on your mounting
surface or refer to quick guide for other xing
options.
03) Thread your mains supply cable through the large
hole in the rear of the case.
04) Secure the rear of the case to your mounting
surface using suitable xings (not supplied), or
refer to quick guide for other xing options.
05) Secure the mains supply cables into the terminal
block according to the terminal identication
marked nex t to the terminal block in the tting:
N - Blue
- Earth
L - Brown
06) Connect the batter y pack lead.
07) Replace the ceiling box cover and secure using the
screw removed earlier.
08) Restore the power supply.
09) The LED indicators should light to indicate correct
charging and the sign panel will also light if the
link between L & LS has been left in place.
NB: To operate as a non-maintained exit sign
remove this link.
The light source is designed to last the lifetime of the
luminaire.
The light source contained in this luminaire
shall only be replaced by the manufacturer,
service agent or a similar qualied person.
CAUTION, RISK OF ELECTRIC SHOCK.
OPERATION CHECKS:
Periodic testing should be carried out to ensure
emergency lighting is operating correctly.
Interruption of the supply, causing the tting to be
energised from the battery, should be carried out by
the operation of a local keyswitch or other isolation
device. During this period all ttings should be
examined visually to ensure that they are func tioning
correctly. At the end of the test period the supply
shall be restored and all indicator lamps or devices
checked to ensure that the normal supply has been
restored.
DA ILY:
Visual inspection of the battery charge LED.
EACH MONTH:
Isolate the power supply for a period sucient to
ensure that each lamp is illuminated. Endorse the
test record form supplied.
ONCE EACH YEAR:
Isolate the power supply and check that the light is
still illuminated after 3 hours. Endorse the test record
form.
Because of the possibility of a failure of the normal
lighting supply occurring shortly af ter a period of
testing of the emergency lighting system or during
the subsequent recharge period, all full duration
tests shall wherever possible be under taken
preceding time of low risk to allow for batter y
recharge.
NOTE: please keep this instruction booklet and
the test record in a safe place. A re ocer or
other authorised person may want to see your
record of inspection and testing.
NOTE: this unit has a permanent live mains supply,
please ensure you isolate before removing cover.
Blue
Green/Yellow
Black
Brown
LN
LS
NEUTRAL
EARTH
LIVE
LINK WIRE
There may also be a seperate switched supply that
controls the emergency light tting - this also needs
to be isolated.
Loading...