Eterna Lighting EBPM3 Installation Instructions

REPLACEMENT BATTERY TYPE:

3.6V 3.0Ah Ni-CD.

BATTERY REPLACEMENT:

If after routine operation check, the lamp does not
remain lit for the three hour period, a new bat tery
pack may be required.

01) Switch o the electricity at the mains.

02) Allow batteries to fully discharge then reconnect
to supply and allow to charge for 24 hours.

03) Test again for 3 hours, if light does not remain lit
change the battery pack as follows:

04) Isolate the mains supply to the unit.

05) Remove the cover of emergency pack.

06) Unplug the battery lead.

07) Remove the battery pack .

08) Write current date on the new emergency pack.

09) Fit new battery pack.

10) Replace cover.

11) Restore power and allow to charge for 24 hours.

12) Perform operation check and update test record.

IMPORTANT NOTES:

The ballast and control gear must be operated only
within the enclosure supplied. The gear must not be
operated outside of the enclosure.

The battery charging circuit and DC ballast are
separated from the mains by at least basic (single
layer) insulation.

When energised by a constant mains supply, the
battery will be constantly charged whether or not
the lamp is illuminated. On failure of the constant
mains supply, the tting will switch automatically
using transistorised switching from battery charging
to battery discharge powering the lamp whether
or not the lamp was illuminated before the power
failure. Both the mains and battery supplies
incorporate fuse protection: see tting for location
and rating.

If battery short circuits on battery terminals then
fuse needs to be replaced before recharging.

Ballast is proofed against polarity reversal.

EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:

Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European “WEEE
Directive” eective August 2005—UK WEEE Regulations
eective 2nd January 2007). Environment Agency
Registered Producer: WEE/GA0248QZ.

WHEN YOUR PRODUC T COMES TO THE END O F ITS
LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE RECYCLE
IT WHER E FACILITIES EXIST  DO NOT DISPOSE WITH
HOUSEHOLD WASTE.

INDUSTRIAL BATTERIES:

Within cer tain products Eterna Lighting Ltd places lead
acid, lithium ion, nickel cadmium & nickel metal hydride
batteries on the market. Industrial batteries are subject
to waste regulation under the Waste Batteries and
Accumulators Regulations 2009 and should be disposed
of responsibly. Purchasers may be able to dispose of
their waste industrial batteries locally via legitimate
licensed trade waste contractors. Eterna is obliged
to take back, free of charge and within a reasonable
time, waste industrial batteries of the same chemistry
supplied to a Purchaser, for treatment and rec ycling
and is required to do this in any calendar year new
industrial batteries are placed on the market. In cer tain
circumstances, this may include batteries not originally
supplied by Eterna. If any Purchaser requires Eterna
to take back Industrial bat teries, they should write to
the Operations Direc tor, Eterna Lighting Ltd, Huxley
Close, NN8 6AB, who will then advise on the necessary
arrangements for the receipt, proper treatment and
recycling of, the waste industrial batteries.

CLEANING:

Clean this t ting only with a soft dry cloth.

Do not use any chemical or abrasive cleaners.

IF YOU EXPERIENCE PROBLEMS:

If you believe your produc t is defective, please return it
to the place where you bought it. Our Technical Team
will gladly advise on any Eterna Lighting product, but
may not be able to give specic instructions regarding
individual installations.

INSTALLATION INSTRUCTIONS

A guide for qualied electricians

3 HOURS DURATION IN EMERGENCY MODE

DANGER!

NOTE: this unit has a

permanent live mains supply,

please ensure you isolate

before removing cover. There is

Pack contents:

1 x Emergency pack
1 x Maintenance check record

Emergency Pack For Commercial

LED Downlights & LED Panel Lights

Model:

EBPM3

also a seperate switched supply

that controls the emergency

light tting - this also needs to

be isolated.

Email: [e-mail] / [e-mail]

Visit our website: www.eterna-lighting.co.uk

Made in China

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION

Made in ChinaIssue 0516

These instructions are provided as a guideline to assist you.

AND RETAIN FOR FUTURE REFERENCE

READ THIS FIRST:

Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.

This tting must be installed by a competent person
in accordance with the current building and IEE
wiring regulations.

As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this tting
is t for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.

Switch o the mains before commencing installation
and remove the appropriate circuit fuse or lock of
MCB.

Disconnec t from the electrical supply before ash or
high voltage testing.

This unit is suitable for indoor use only.

Do not cover the t ting with any insulating materials.

This product is designed for permanent connection
to xed wiring: this should be a suitable circuit
(protected with the appropriate MCB or fuse)

When making connections, ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation.

This product must be connected to Ear th
termination.

Make connections to the electrical supply in
accordance with the following code:

Live: Brown or Red (L)
Neutral: Blue or Black (N)
Earth: Green and Yellow (E)

You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out:
these tests are specied in the Wiring Regulations
(BS7671) referred to in the Building Regulations.

The batteries supplied with this tting are a
consumable part and therefore may be outside of
any warranty oered.

INSTALLATION:

DANGER! Please note that there are two live

supplies, one switched and one permanent; please
ensure you isolate both before you undertake any
work on the emergency tting.

This emergency pack is designed for use with the
Eterna General Purpose Downlight and Panel Light.

01. Switch o the mains before commencing
installation and remove the appropriate circuit
fuse or MCB.

02. Site the emergency pack within one metre of the
luminaire to be converted.

03. Connect a permanent live supply to the
emergenc y pack & connect the battery cables.

LED PANEL LIGHT INSTALLATION:

NOTE: Before commencing installation or

maintenance ensure that the mains supply is
isolated and locked o.

NOTE: If using with suface mount (SURFMK),
remove control gear from box.

1. Remove the cable from the driver supplied.

2. Connect the cable from the panel / downlight to

the supplied connection box.

3. Connect the emergency pack output trailing lead

marked “LED Light” to the connection box making
sure the polarity is observed.

4. Connect the emergency pack lead marked “LED

Driver” to the output side of the driver which was
supplied with the panel / downlight.

5. Connect 240V mains switch supply to the input

side of the driver.

6. Connect a permanent 240V mains supply to the

emergency pack.

7. Connect the two battery leads from the pack.

8. Insert the green LED indicator into the 5mm hole

and secure in place using a cable tie; the green LED
should be visible when the light is on.

9. Mark the installation date on the battery pack.

10. Restore power; a green indicator light will be
present to show that the batteries are charging.

NOTE: For non-maintained operation do not
connect a switched supply to the tting.

OPERATION CHECKS:

Periodic testing should be carried out to ensure
emergency lighting is operating correctly.
Interruption of the supply, causing the tting to be
energised from the battery, should be carried out by
the operation of a local keyswitch or other isolation
device. During this period all ttings should be
examined visually to ensure that they are functioning
correctly. At the end of the test period the supply
shall be restored and all indicator lamps or devices
checked to ensure that the normal supply has been
restored.

DA ILY:

Visual inspection of the battery charge LED.

EACH MONTH:

Isolate the power supply for a period sucient to
ensure that each lamp is illuminated. Endorse the
test record form supplied.

ONCE EACH YEAR:

Isolate the power supply and check that the light is
still illuminated after 3 hours. Endorse the test record
form.

Because of the possibilit y of a failure of the normal
lighting supply occurring shortly after a period of
testing of the emergency lighting system or during
the subsequent recharge period, all full duration
tests shall wherever possible be undertaken
preceding time of low risk to allow for battery
recharge.

NOTE: please keep this instruction booklet and
the test record in a safe place. A re ocer or
other authorised person may want to see your
record of inspection and testing.

Permanent Mains
Power Supply
(220-240V)

Emergency Box
(EBPM3)

L

N

Light
cable

Indicator LED Charge

Driver Cable

LED Light Cable

Panel
Light

Cable tie

Driver

Connection Box

5mm
hole

SW

L1

N

LED
Light

Battery