Children of less than 3 years should be kept away from the
heater unless continuously supervised.
Children aged from 3 years and less than 8 years shall only
switch on/o the appliance provided that it has been placed
WARNING!
or installed in its intended normal operating position and
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Children aged from 3 years and less than 8 years shall not plug in, regulate
and clean the appliance or perform user maintenance.
SOME PARTS OF THIS
PRODUCT CAN BECOME
VERY HOT AND CAUSE
BURNS. PARTICULAR
ATTENTION HAS TO BE
GIVEN WHERE CHILDREN
CAUTION!
AND VULNERABLE
PEOPLE ARE PRESENT.
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
CLEANING:
• Always remove the plug from the electrical socket
and allow the heater to cool down before cleaning
the heater.
• Wipe heater with a soft dry cloth.
• Store the heater in a clean dry place.
CLEANING WARNING:
Do not immerse the heater in
water.
Do not use any cleaning chemicals
such as detergents and abrasives.
Do not allow the interior to get
wet.
Email: sales@eterna-lighting.co.uk / technical@eterna-lighting.co.uk
Visit our website: www.eterna-lighting.co.uk
EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.
Made in ChinaIssue 0617
Pack contents:
1 x Convector heater c/w 13A.
fused 3 pin plug tted
2 x Mounting feet
4 x Feet xing screws
4 x Wall mounting brackets
4 x Wall plugs
Model:
4 x Wall xing screws
CONVECTSTD
2kW Convector Heater
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
READ THIS FIRST:
Check the pack and make sure you have all of the parts
listed on the front of this booklet. If not, contact the
supplier where you bought this product.
IMPORTANT SAFEGUARDS:
When using an electrical appliance, basic safety
precautions should always be observed, including the
following:
If operating the heater as a freestanding appliance,
ensure the feet are correctly at tached beforehand.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruc tion concerning use of the appliance by a
person responsible for their safety.
Extreme caution is necessary where children
with reduced physical, sensory or mental capabilities may
come into contact with the heater when in use.
The product is for household/oce use only.
WARNING -
In order to avoid
or persons
overheating do not cover or
obstruct grilles or air intake
openings when in use.
Do not place the heater on carpets with a very
pile.
Always ensure that the heater is placed on a
surface and ensure that the heater is not positioned close
to ammable materials, such as curtains, drapes etc as this
could create a re hazard.
The heater must not be located adjacent to or
an electrical socket.
Do not run the cord under carpets/rugs.
Arrange the cord away from high trac areas and
where it will not become a trip hazard.
Keep the mains lead away from the
Do not operate the heater with a damaged
or if the heater malfunctions.
If the supply cord is damaged, it must be
qualied engineer.
Avoid the use of an e xtension cord as this may
and cause a risk of re.
Do not use the heater in any areas where
or other ammable liquids or ammable fumes may be
present e.g. garages or workshops.
Do not use this heater in the immediate
of a bath, shower, swimming pool or where water is
present.
This heater is hot when in use. To avoid burns
personal injury, do not let bare skin touch hot surfaces.
Never leave the heater unat tended whilst it is
SPECIFICATION:
VOLTAGE: 220-240V ~ 50Hz
POWER MAX: 2kW
heater when in use.
deep
rm level
against
cord/plug
replaced by a
overheat
petrol, paint
surroundings
and
in use.
WARNING:
This product must only be operated in an upright
position.
Do not try to repair the heater yourself, always
consult a suitably qualied engineer.
OPERATION OF THE HEATER:
NOTE: It is normal for the heater to smell slightly for a
short while when turned on for the rst time or after a
period of not being used.
ATTACHING THE FEET:
1. Tip heater upside down.
2. Attach feet to each end of the heater using the
screws provided. Ax the feet using 2 screws
diagonally to correspond with the pre cut holes.
Fasten securely.
3. Turn heater correct way up.
WALL MOUNTING THE HEATER:
CAUTION: The heater must be installed away from
ammable surfaces at least 40cm between the lower
part of the appliance and the oor, 50cm in front/side
and 100cm below any given sur faces as shown in g.
1 opposite.
The feet must be removed before mounting the
appliance on the wall.
1. Measure the distance between the two slots
situated at the back of the appliance (see g.2).
2. Using this and the mounting bracket as a guide drill two holes in the wall and inser t a wall plug in
each hole.
3. Place the brackets facing the holes as indicated on
g.3 (slots upwards) and attach them in this position
with the screws supplied.
4. Before attaching the appliance on the brackets,
attach the two other brackets underneath the
appliance as indicated on g.4.
5. Attach the appliance on the wall. To do so,
it in such way that the slots are facing the brackets;
insert the appliance halfway onto the brackets until
the appliance can go down into the grooves of the
brackets.
6. As soon as the appliance is positioned correctly,
take a pencil and mark a dot in the hole of each bracket
situated underneath the appliance.
7. Then remove the appliance.
8. Drill a hole in the wall as marked and inser t a
plug in each hole.
9. Attach the appliance back on the wall as
point 5, insert screws through the brackets underneath
the appliance and tighten.
hold
wall
indicated in
Fig 1
100cm 40cm
50cm 50cm
INSTRUCTIONS FOR USE:
Choose a suitable location for the heater, taking
into account the safety instructions above.
Insert the plug of the heater into a suitable socket.
Turn the thermostat knob fully in a clockwise direction
to the maximum setting.
Turn on the heating elements by means of the
rocker switches on the side panel. When the heating
elements are on the switches will illuminate. For
maximum heat output both switches should be on.
Example:
Switch 1 = 750W | Switch 2 = 1.25kW | Combined = 2kW
When the desired room temperature has been
reached, the thermostat knob should be turned slowly
anti-clockwise until the thermostat click is heard and
the lights on the element switches are seen to go out.
After this the heater will keep the air temperature in
the room at the set temperature by switching on and
o automatically.
Fig 2
Back View
x2
Fig 3
Base View
Fig 4
Loading...