Eterna Lighting CO12SCEM3 Installation Instructions

INSTALLATION INSTRUCTIONS

A guide for qualied electricians

3 HOURS DURATION IN EMERGENCY MODE

EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:

Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK WEEE
Regulations eective 2nd January 2007). Environment
Agency Registered Producer: WEE/GA0248QZ.

WHEN YOUR PRODUC T COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.

INDUSTRIAL BATTERIES:

Within certain produc ts Eterna Lighting Ltd places
lead acid, lithium ion, nickel cadmium & nickel metal
hydride batteries on the market. Industrial batteries
are subject to waste regulation under the Waste
Batteries and Accumulators Regulations 2009 and
should be disposed of responsibly. Purchasers may
be able to dispose of their waste industrial batteries
locally via legitimate licensed trade waste contractors.
Eterna is obliged to take back , free of charge and
within a reasonable time, waste industrial batteries
of the same chemistry supplied to a Purchaser, for
treatment and recycling and is required to do this in
any calendar year new industrial batteries are placed
on the market. In certain circumstances, this may
include batteries not originally supplied by Eterna. If
any Purchaser requires Eterna to take back Industrial
batteries, they should write to the Operations
Director, Eterna Lighting Ltd, Huxley Close, NN8 6AB,
who will then advise on the necessary arrangements
for the receipt, proper treatment and recycling of, the
waste industrial batteries.

CLEANING:

Clean this tting only with a soft dry cloth.

Do not use any chemical or abrasive cleaners.

IF YOU EXPERIENCE PROBLEMS:

If you believe your product is defective, please
return it to the place where you bought it. Our
Technical Team will gladly advise on any Eterna
Lighting product, but may not be able to give specic
instructions regarding individual installations.

Pack contents:
1 x LED ceiling tting
1 x Maintenance Check Record

Model:

CO12SCEM3

Email: [e-mail] / [e-mail]

Visit our website: www.eterna-lighting.co.uk

12W IP65 LED Circular Ceiling/Wall Light With Emergency

These instructions are provided as a guideline to assist you.

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION

AND RETAIN FOR FUTURE REFERENCE

Made in ChinaIssue 0121

READ THIS FIRST:

This product must be installed by a competent
person in accordance with the current building and
IEE wiring regulations.

As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this tting
is t for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.

Switch o the mains before commencing installation
and remove the appropriate circuit fuse or lock o
MCB.

WARNING: There are two mains feed. Disconnect
both before removing cover.

The batteries supplied with this tting are
consumable parts and therefore may be outside of
any warranty oered.

This unit is suitable for indoor or outdoor use.

This product is suitable for installation on surfaces
with normal ammability e.g. wood, plasterboard
and masonry. It is not suitable for use on highly
ammable sur faces (e.g. polystyrene, textiles).

Before making xing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.

Ensure that the tting will be accessible after
installation for maintenance and self testing.

When making connections ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation.

This product is double insulated, do not connect any
part to Earth.

You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out,
these tests are specied in the current IEE wiring and
building regulations.

Brown
(Power Cable)

White L’ - L
(Loop Cable)

Blue
(Power Cable)

L L’ N

LIVE
(Power Cable)

NEUTRAL
(Power Cable)

INSTALLATION:

Choose the location for your new tting according to
the conditions listed opposite.

01) Remove diuser.

02) Unscrew the gear tray screw and allow the gear
tray to rest on its hinge.

03) Drill holes in the back of your tting for your
xing screws, take care and drill gently to
ensure a clean hole through. Use a drill bit sized
appropriately to your xing screws (not supplied).

04) Using the back of your tting as a template,
mark the position of your xing holes on your
mounting sur face.

05) Prepare the holes in your mounting sur face as
appropriate for your xings.

06) Pierce the rubber grommet in the back of your
tting making a hole just large enough to make a
tight t around the incoming mains cable.

07) Thread the cable through the grommet and oer
the tting to the ceiling / wall.

08) Secure the tting in place. Note, if protection
against ingress of moisture is required, the heads
of screws must be covered with a silicone or
similar sealant.

09) Check that the grommet is still correctly tted in
the cable entry hole and around the incoming
cable.

10) Make the electrical connections to the terminal
block according to the markings:

Brown to live (L) • Blue to neutral (N)

11) Mark the current date on the bat tery pack.

12) Ensure the battery plug is connected to the
socket on the driver.

13) Replace diuser and apply decorative trim if
using.

14) Restore the power and check tting is working
correctly. A green light should always be present
indicating the tting is charging.

NOTE: For non-maintained operation, remove
link wire from L and L1.
For switched operation, remove link wire and
make a switched supply into L1.

OPERATION CHECKS:

Periodic testing should be carried out to ensure
emergency lighting is operating correctly.
Interruption of the supply, causing the tting to be
energised from the battery, should be carried out by
the operation of a local keyswitch or other isolation
device. During this period all ttings should be
examined visually to ensure that they are func tioning
correctly. At the end of the test period the supply
shall be restored and all indicator lamps or devices
checked to ensure that the normal supply has been
restored.

DA ILY:

Visual inspection of the battery charge LED.

EACH MONTH:

Isolate the power supply for a period sucient to
ensure that each lamp is illuminated. Endorse the
test record form supplied.

ONCE EACH YEAR:

Isolate the power supply and check that the light is
still illuminated after 3 hours. Endorse the test record
form.

Because of the possibility of a failure of the normal
lighting supply occurring shortly af ter a period of
testing of the emergency lighting system or during
the subsequent recharge period, all full duration
tests shall wherever possible be under taken
preceding time of low risk to allow for batter y
recharge.

NOTE: please keep this instruction booklet and
the test record in a safe place. A re ocer or
other authorised person may want to see your
record of inspection and testing.

BATTERY REPLACEMENT:

If after routine operation check, the lamp does not
remain lit for the three hour period, a new battery
pack may be required.

01. Switch o the electricity at the mains (both
permanent live and switch live) and allow
batteries to fully discharge then reconnect to
supply and allow charging for 24 hours.

02. Test again for 3 hours, if light does not remain lit,
then change the battery pack as follows:

03. Remove the diuser and remove the gear tray.

04. Remove the battery case from the gear and

remove the battery.

05. Write current date on the new battery pack and t
a new battery by reversing the above procedure.

06. Plug battery pack into circuit board.

07. Ret gear tray and diuser.

08. Restore power and allow charging for 24 hours.

09. Perform full operation check and update test
record.

REPLACEMENT BATTERY TYPE:

3.2V 1500mAh Lithium

LAMP REPLACEMENT:

The light source is designed to last the lifetime of the
luminaire.

The light source contained in this luminaire
shall only be replaced by the manufacturer,
service agent or a similar qualied person.

CAUTION, RISK OF ELECTRIC SHOCK.