Eterna vnanobh Installation Instructions Manual

Model:

VNANOBH

8W LED Nano Bulkhead

These instructions are provided as a guideline to assist you.

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION

AND RETAIN FOR FUTURE REFERENCE

INSTALLATION INSTRUCTIONS

A guide for qualied electricians

874/2012

MODELNO.

VNANOBH

Pack contents:

1 x LED bulkhead

1 x Fixing kit

Email: [e-mail] / [e-mail]

Visit our website: www.eterna-lighting.co.uk

Made in ChinaIssue 0617

EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:

Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Direc tive” eective August 20 05—UK
WEEE Regulation s eective 2nd January 20 07).
Environment Agenc y Registered Producer : WEE/
GA0248Q Z.

WHEN YOUR PR ODUCT COMES TO TH E END OF
ITS LIFE OR YO U CHOOSE TO REPLACE I T, PLEA SE
RECYCLE IT W HERE FACILITIES E XIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.

CLEANING:

Clean this ttin g only with a soft dry clo th.

Do not use any chemic al or abrasive cleaners.

IF YOU EXPERIENCE PROBLEMS:

If you believe your p roduct is defective, p lease return
it to the place where yo u bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, bu t may not be able to give specic
instructions regarding individual installations.

LED LAM P SPECIFICATIO NS:

Luminaire lumens (with
diuser)

700 lm

Lumens from chip (no
diuser)

750 lm

Rated Wattage 8W

Rated luminous ux 700 lm

Nominal life time of the lamp 30,000 hrs

Colour temperature 4200K

Number of switching cycles
before premature lamp
failure

>15,000

Warm-up time up to 60% of
the full light output

Instant full light

Dimmable No

Nominal beam angle >120°

Rated power 8W

Rated lamp lifetime 30,000 hrs

Lamp power factor >0.5

Lumen maintenance factor at
end of nominal life

>0.7

Starting time <0.5

Colour rendering >80

Colour consistency

Within a six step

Macadam ellipse

Rated beam angle >120°

Voltage / Frequency 240V~50Hz

Not suitable for accent lighting

READ THIS FIRST:

Check the pack and m ake sure you have all of the
parts liste d on the front of this bookle t. If not,
contact the outlet where you bought this product.

This produ ct must be install ed by a competent
person in accordance with the current building
and IEE wiring regulations.

As the buyer, install er and/or user of this product it
is your own responsi bility to ensure that this tt ing
is t for the purpo se for which you have intended
it. Eterna Lightin g cannot accept any liability fo r
loss, damage or premature failure resulting from
inappropriate use.

Switch o the mains be fore commencing installati on
and remove the appro priate circuit fuse or lock o
MCB.

This unit is suitable for indoor and outdoor use.

This produc t is designed for permanent co nnection
to xed wiring: this m ust be a suitable circuit
(protected w ith the appropriate MCB or fuse).

This produc t is suitable for installatio n on surfaces
with normal ammability e.g. wood, plasterboard
and masonry. It is not s uitable for use on highly
ammable sur faces (e.g. polystyren e, textiles).

Before makin g xing hole(s), check that there are no
obstructi ons hidden beneath the mount ing surface
such as pipes or cab les.

When making con nections ensure that the ter minals
are tightened se curely and that no strands of wi re
protrude. Chec k that the terminals are tightene d
onto the bared cond uctors and not onto any
insulation.

This produc t is double insulated; do not conne ct
either the blue /brown wires or any part to the e arth
terminal.

You are advised at ever y stage of your installatio n to
double-check any electrical connections you have
made. After you h ave completed your installatio n
there are elec trical tests that should b e carried out,
these tests are sp ecied in the current IEE wir ing and
building regulations.

LAMP REPLACEMENT: INSTALLATION:

Choose the loc ation for your new light tting
according to the conditions listed opposite.

01) Isolate the mains before comme ncing installation.

02) Using the base as a template, ma rk the position of
the xing holes.

03) Undo the two screws ho lding the diuser in place
and unscrew the LED ar ray.

04) Pierce the rubbe r grommet and thread the mains
supply cable th rough it.

NOTE: Do not make th e holes in the grommet
too large. They sh ould be tight on the cable to
ensure a water-tight seal.

05) Make the terminal conn ections:
Live (L), Neutral (N).

06) Replace the LED ar ray and diuser.

07) Restore power an d switch on.

The light source cont ained in this luminaire
shall only be rep laced by the manufacturer,
service age nt or a similar qualied pers on.

CAUTION, RISK OF ELECTRIC SHOCK.

The light source is designed to last the lifetime of the
luminaire.