Eterna FOCUS10PIR, FOCUS20PIR, TAB10PIRWH, TAB20PIRWH, TAB30PIRWH Installation Instructions Manual

These instructions are provided as a guideline to assist you.

PLEASE READ THESE INSTRUCTIONS BEFORE USING YOUR NEW FITTING

PLEASE RETAIN FOR FUTURE REFERENCE

INSTALLATION INSTRUCTIONS

A guide for qualied electricians

Model:

FOCUS10PIR / FOCUS20PIR

10W / 20W Focus LED Floodlights With PIR

PG 6 PG 1

1M

EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:

Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Direc tive” eective August 20 05—UK
WEEE Regulation s eective 2nd January 20 07).
Environment Agenc y Registered Producer : WEE/
GA0248Q Z.

WHEN YOUR PR ODUCT COMES TO TH E END OF
ITS LIFE OR YO U CHOOSE TO REPLACE I T, PLEASE
RECYCLE IT W HERE FACILITIES E XIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.

IF YOU EXPERIENCE PROBLEMS:

If you believe your p roduct is defective, p lease return
it to the place where yo u bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, bu t may not be able to give specic
instructions regarding individual installations.

874/2012

MODELNO.

FOCUS RANGE

Email: [e-mail] / [e-mail]

Visit our website: www.eterna-lighting.co.uk

Made in ChinaIssue 1016

Pack contents:

1 x Focus LED oodlight with PIR

10W

20W

LAMP SPECIFICATIONS: 10W 20W

Lumens total ux

680 lm 1500 lm

Lumens 90° ux

640 lm 1400 lm

Rated Wattage 10W 20W

Rated luminous ux 680 lm 1360 lm

Nominal life time of the lamp 25,000 hrs 25,000 hrs

Colour temperature 4200K 4200K

Number of switching cycles
before premature lamp
failure

15,000 15,000

Warm-up time up to 60 % of
the full light output

Instant full light Instant full light

Dimmable No No

LED array dimensions (Ø) 29mm 29mm

Nominal beam angle 40° 100°

Rated power 10W 20W

Rated lamp lifetime 25,000 hrs 25,000 hrs

Lamp power factor >5 >5

Lumen maintenance factor at
end of nominal life

70% 70%

Starting time 0.17s 0.34s

Colour rendering ≥65 ≥65

Colour consistency

Within 6 step

Macadam ellipse

Within 6 step

Macadam ellipse

Rated peak intensity 300cd 600cd

Rated beam angle 40° 100°

Voltage 240V 240V

WHERE TO F IT YOUR PIR FLOODLI GHT:

To achieve best results we su ggest you take the
following points into consideration:

Do not mount on a sur face that has vibration.

Ideally the PIR o od light should be mounted 3
metres above the ar ea to be scanned (refer to g.1
below).

To avoid damage to the unit do not ai m sensor
towards sun.

Avoid positioning th e sensor unit adjacent to a
bright light source w hich may prevent the unit from
operating whe n the lux control is set to operate i n
dark conditions.

Avoid nuisance / false t riggering by directing s ensor
away from:

• Trees and shrubs

• Reective su rfaces such as smooth white w alls

• Swimming pools

• Heat sources such as b oiler ues

The PIR sensor sc anning specications
(approximately 10 metres at 140° ) may vary slightly
depending on the mounting height and location.

The detecti on range of the unit may also alter w ith
temperature cha nge. Before selectin g a place to
install your PIR o odlight you should note that
movement across the s can area is more eective
than movement dire ctly towards or away from the
sensor. (Refer to g. 2 opposite).

If movement is made w alking directly towards o r
away from the senso r and not across the sensor
the apparent dete ction range will be subs tantially
reduced (refer to g . 3 below).

INTRODUCTION:

The oodlight i ncorporates a PIR (Passive Infra R ed)
sensing device wh ich continuously scans a prese t
operating zon e and immediately switches th e light
on when it detec ts movement in that area.

This means that whe never movement is detecte d
within the range o f the sensor the light will switch
on automaticall y to illuminate the area you have
selected to l ight. While there is movement wi thin
range of the unit th e light will remain on.

READ THIS FIRST:

Check the pack and m ake sure you have all of the
parts liste d on the front of this bookle t. If not,
contact the outlet where you bought this product.

This produc t must be installed by a compet ent
person in accord ance with the current building a nd
IEE wiring regulations.

As the buyer, install er and/or user of this product it
is your own responsi bility to ensure that this tt ing
is t for the purpo se for which you have intended
it. Eterna Lightin g cannot accept any liability fo r
loss, damage or premature failure resulting from
inappropriate use.

This product is designed and constructed according
to the principles of the appropriate British Standard.

Switch o the mains be fore commencing installati on
and remove the appro priate circuit fuse or lock o
MCB.

This unit is suitab le for outdoor use.

This produc t is designed for permanent co nnection
to xed wiring: this m ust be a suitable circuit
(protected w ith the appropriate MCB or fuse).

Before makin g xing hole(s), check that there are no
obstructi ons hidden beneath the mount ing surface
such as pipes or cab les.

Make sure that the xi ngs are strong enough to
support the co nsiderable weight of the t ting and
hold it rigidly.

The lamp must be p ositioned so that there is at
least 1M between th e luminaire and any illuminated
surface.

When making con nections ensure that the ter minals
are tightened se curely and that no
strands of wire p rotrude. Check that the termin als are
tightened onto the b ared conductors and not o nto
any insulation.

This product is double insulated. DO NOT CONNECT

ANY PART TO EARTH.

This produc t is not intended to be used by childr en
and persons wi th sensory, physical and/or ment al
impairments th at would prevent them from using i t
saf ely.

You are advised at ever y stage of your installatio n to
double-check any electrical connections you have
made. After you h ave completed your installatio n
there are elec trical tests that should b e carried out,
these tests are sp ecied in the current IEE wir ing and
building regulations.

CLEANING:

• To avoid dust build-up and ensur e proper
functionin g of the oodlight, please w ipe the
sensor lens light ly with a damp cloth every 3
months.

• Disconnect the po wer and clean the exterior o nly of
this tting wit h a moist (not wet) cloth.

• Do not use any chemic al or abrasive cleaners.

LAMP REPLACEMENT:

The light source of th is luminaire is not replaceable;
when the light sou rce reaches its end of life the
whole luminaire shall be replaced.

SPECIFICATIONS:

• Detection rang e: max. 10M at approx. 140° scan

• Duration time adjust ment: (10±2) seconds to (10±2)
minutes

• Detection c ircuitry: Passive Infra -Red (PIR)

• Weather proof: IP54

• Power required: 240V~ 50 Hz

• Recommended powe r supply cable: H05RN- F 3G

1.0m m

2

• Protection: Cla ss II

• Lux level: adjust able

NOTE: the PIR head c an be rotated 90° lef t or right

3M

4M 8M 10M

140˚

Approx

Fig 1

EFFECTIVE:

Movement across
scan area

LESS EFFECTIVE:

Movement
directly in front
of scan area

Fig 2

Fig 3

PG 2 PG 3