Eterna MODERNOBK, MODPIRBK, MODERNOWH, MODPIRWH Installation Instructions And Operators Manual

Model:

MODERNOBK / MODERNOWH

MODPIRBK / MODPIRWH

6W LED Lantern / 6W LED Lantern With PIR

These instructions are provided as a guideline to assist you.

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION

AND RETAIN FOR FUTURE REFERENCE

INSTALLATION INSTRUCTIONS

A guide for qualied electricians

874/2012

MODELNO.

MODERNO RANGE

EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:

Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Direc tive” eective August 20 05—UK
WEEE Regulation s eective 2nd January 20 07).
Environment Agenc y Registered Producer : WEE/
GA0248Q Z.

WHEN YOUR PR ODUCT COMES TO TH E END OF
ITS LIFE OR YO U CHOOSE TO REPLACE I T, PLEASE
RECYCLE IT W HERE FACILITIES E XIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.

CLEANING:

Disconnect t he power and clean the exte rior only of
this tting wit h a moist (not wet) cloth.

Do not use any chemic al or abrasive cleaners.

IF YOU EXPERIENCE PROBLEMS:

If you believe your p roduct is defective, p lease return
it to the place where yo u bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, bu t may not be able to give specic
instructions regarding individual installations.

Email: [e-mail] / [e-mail]

Visit our website: www.eterna-lighting.co.uk

Made in ChinaIssue 1116

PG 6 PG 1

Pack contents:

1 x LED lantern

LED LAM P SPECIFICATIONS:

Lumens total ux

330 lm

Lumens 120° ux

300 lm

Rated Wattage 6W

Rated luminous ux 300 lm

Nominal life time of the lamp 35,000 hrs

Colour temperature 3100K

Number of switching cycles
before premature lamp
failure

≥15,000

Warm-up time up to 60 % of
the full light output

Instant full light

Dimmable No

LED array dimensions (Ø) 65mm

Nominal beam angle 120°

Rated power 6W

Rated lamp lifetime 35,000 hrs

Lamp power factor >0.5

Lumen maintenance factor at
end of nominal life

≥0.70

Starting time <0.1s

Colour rendering ≥80

Colour consistency

Within 6 step

Macadam ellipse

Rated peak intensity 120cd

Rated beam angle 120°

Voltage 240V

Not suitable for accent lighting

PG 2 PG 3

READ THIS FIRST:

Check the pack and m ake sure you have all of the
parts liste d on the front of this bookle t. If not,
contact the outlet where you bought this product.

This produc t must be installed by a compet ent
person in accord ance with the current building a nd
IEE wiring regulations.

As the buyer, install er and/or user of this product it
is your own responsi bility to ensure that this tt ing
is t for the purpo se for which you have intended
it. Eterna Lightin g cannot accept any liability fo r
loss, damage or premature failure resulting from
inappropriate use.

This product is designed and constructed according
to the principles o f the appropriate British Stan dard
and is intended fo r normal domestic ser vice. Using
this tting in any oth er environments may result in
a shortened w orking life, for example w here there
is prolonged p eriods of use or higher than no rmal
ambient temper atures such as lighting public or
shared spaces.

Switch o the mains be fore commencing installati on
and remove the appro priate circuit fuse or lock o
MCB.

This unit is suitab le for outdoor use.

This produc t is suitable for installatio n on surfaces
with normal ammability e.g. wood, plasterboard
and masonry. It is not s uitable for use on highly
ammable surfaces

Before makin g xing hole(s), check that there are no
obstructi ons hidden beneath the mount ing surface
such as pipes or cab les.

Make sure that the xi ngs are strong enough to
support the co nsiderable weight of the t ting and
hold it rigidly.

The chosen loc ation of your new tting shou ld allow
for the produc t to be securely mounted. An d safely
connected to th e mains supply (lighting circuit).

When choosing th e location for your new tt ing,
ensure that the xin gs will be anchored in a solid
surface e.g. con crete, brick or a joist—do not  x
directly onto panelling, cladding, plasterboard etc.

When making con nections ensure that the ter minals
are tightened se curely and that no strands of wi re
protrude. Chec k that the terminals are tightene d
onto the bared cond uctors and not onto any
insulation.

This tting is d ouble insulated; do not connec t any
part to eart h.

This produc t is not intended to be used by childr en
and persons wi th sensory, physical and/or ment al
impairments th at would prevent them from using i t
saf ely.

You are advised at ever y stage of your installatio n to
double-check any electrical connections you have
made. After you h ave completed your installatio n
there are elec trical tests that should b e carried out,
these tests are sp ecied in the current IEE wir ing and
building regulations.

INSTALLATION:

ISOLATE MAINS BEFORE
CARRYING OUT INSTALLATION

01) Undo the nuts each s ide at the front of the tting
and lift o the f ront section of the lanter n

02) Using the b ack cover of the tting as a template,
mark the locati on of the xing holes.

03) Pierce the r ubber grommet in the back of th e
tting. Make th e hole as small as possible so that
a good watert ight seal is maintained when th e
cable has been threaded through.

04) Th read the cable through the gro mmet.

05) Sec ure the tting to the wall using  xings (not
supplie d).

06) Make t he connections to the termi nal block
according to the colo ur code and symbols:

LIVE - Brown or Red • NEUTRAL - Bl ue or Black

07) Conne ct the two wires from the f ront half of the
lantern to the push ter minal block in line with the
colour code and s ymbols (see g. 4 opposite).

08) Re place the front part of lanter n and secure by
tightening the t wo nuts making sure you have a
rubber sealin g washer under both nuts.

09) Res tore power.

10) Switch on and product should function.

SPECIFICATIONS:

• Det ection range: Approx. 120° (hor izontal), Max. 8

metres.

• Duration time: f rom 5 sec - 5 mins. (adjustable).

• No over ride facility.

• LUX - adjustable.

LAMP REPLACEMENT:

WHERE TO F IT YOUR PIR FU LL LANTERN:

To achieve best results we su ggest you take the
following points into consideration:

Do not mount on a sur face that has vibration.

Ideally the PIR lante rn should be mounted 1.8 to 2.5
metres (6 to 8ft) ab ove the area to be scanned (refer
to Fig. 1 below).

To avoid damage to the unit do not ai m sensor
towards the sun.

Avoid positioning th e sensor unit adjacent to a
bright light source w hich may prevent the unit from
operating whe n the lux control is set to operate i n
dark conditions.

Avoid nuisance false t riggering by directing s ensor
away from:

Trees and shrubs
Reective su rfaces such as smooth white w alls
Swimming pools
Heat sources such as b oiler ues

The PIR sensor sc anning specications
(approximately 8 met res at 120°) may vary slightly
depending on the mounting height and location.

The detecti on range of the unit may also alter
with temperatu re change. Before selec ting a place
to install your PIR lant ern you should note that
movement across the s can area is more eective
than movement dire ctly towards or away from the
sensor (refer to Fig. 2 a bove).

If movement is made w alking directly towards o r
away from the senso r and not across the apparent
detection r ange will be substantially re duced (refer
to Fig. 3 above).

1.8-

2.5M

4M 8M

120˚

Approx

Fig 1

EFFECTIVE:

Movement
across scan area

LESS EFFECTIVE:

Movement directly in front of
scan area

Fig 2

Fig 3

L N

Blue
(Power Cable)

Brown

(Power Cable)
Blue
(Power Cable)

Brown
(Power Cable)

Fig 4

The light source cont ained in this luminaire
shall only be rep laced by the manufacturer,
service age nt or a similar qualied pers on.

CAUTION, RISK OF ELECTRIC SHOCK.

The light source is designed to last the lifetime of the
luminaire.