Eterna LEDBOLLARD Installation Instructions Manual

Model:

LEDBOLLARD

800mm LED Bollard

These instructions are provided as a guideline to assist you.

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION

AND RETAIN FOR FUTURE REFERENCE

INSTALLATION INSTRUCTIONS

A guide for qualied electricians

EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:

Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Direc tive” eective August 20 05—UK
WEEE Regulation s eective 2nd January 20 07).
Environment Agenc y Registered Producer : WEE/
GA0248Q Z.

WHEN YOUR PR ODUCT COMES TO TH E END OF
ITS LIFE OR YO U CHOOSE TO REPLACE I T, PLEA SE
RECYCLE IT W HERE FACILITIES E XIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.

CLEANING:

Disconnect t he power and clean the exte rior only of
this tting wit h a moist (not wet) cloth.

Do not use any chemic al or abrasive cleaners.

IF YOU EXPERIENCE PROBLEMS:

If you believe your p roduct is defective, p lease return
it to the place where yo u bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, bu t may not be able to give specic
instructions regarding individual installations.

Email: [e-mail] / [e-mail]

Visit our website: www.eterna-lighting.co.uk

Made in ChinaIssue 1216

874/2012

MODELNO.

LEDBOLLARD

Pack contents:

1 x LED tting

3 x J bolts

3 x Base screws

3 x Washers

6 x Head screws

1 x Surface mounti ng

plate

LED LAM P SPECIFICATIO NS:

Luminaire lumens (with diuser)

430 lm

Lumens from chip (no diuser)

670 lm

Useful lumens

400 lm

Rated Wattage 7W

Rated luminous ux 400 lm

Nominal life time of the lamp 30,000 hrs

Colour temperature 4000K

Number of switching cycles
before premature lamp failure

15,000

Warm-up time up to 60% of the
full light output

Instant full light

Dimmable No

Nominal beam angle 120°

Rated power 7W

Rated lamp lifetime 30,000 hrs

Lamp power factor 0.86

Lumen maintenance factor at end
of nominal life

70%

Starting time <0.5s

Colour rendering >80

Colour consistency

Within a six step

Macadam ellipse

Rated peak intensity 94cd

Rated beam angle 120°

Voltage / Frequency 240V~50Hz

Not suitable for accent lighting

READ THIS FIRST:

Check the pack and make sur e you have all of
the parts liste d on the front of this booklet. I f
not, contact the o utlet where you bought this
product.

This produc t must be installed by a c ompetent
person in accordance with the current
building and IEE wiring regulations.

As the buyer, installer an d/or user of this product
it is your own responsibi lity to ensure that this
tting is t for the p urpose for which you have
intended it. Eterna L ighting cannot accept any
liability for los s, damage or premature failure
resulting from inappropriate use.

This product is designed and constructed
according to the princip les of the appropriate
British Standard and is inte nded for normal
domestic ser vice only not suitable for commercia l
use and is not classed as v andal proof.

Switch o the mains befor e commencing
installation and remove the appropriate circuit
fuse or lock o MCB.

This unit is suitable for outdoor use and
should be pr otected by a 30mA RCD.

This product is d esigned for permanent
connection to xe d wiring: this must be a suitable
circuit (protecte d with the appropriate MCB or
fuse).

Before making  xing hole(s), check that there are
no obstructions hidden beneath the mounting
surface such as pip es or cables.

Make sure that the xings ar e strong enough
to support the wei ght of the tting and hold it
rigidly.

The chosen locat ion of your tting should allow
for the product to b e securely mounted and
anchored to a solid sur face e.g. concrete, brick.

This produc t must be connecte d to earth
termination.

Make connection s to the electrical supply in
accordance with the following code:

Live – Brown or Red
Neutral – Blue or Bla ck
Earth – Green an d Yellow

When making conne ctions ensure that the
terminals are tightene d securely and that no
strands of wire prot rude. Check that the terminals
are tightened onto the ba red conductors and not
onto any insulation.

This product is n ot intended to be used by
children and persons with sensory, physical and/
or mental impairm ents that would prevent them
from using it safel y.

You are advised at every st age of your installation
to double- check any electrical connec tions
you have made. After you have com pleted your
installation ther e are electrical tests that shou ld
be carried out , these tests are specied in the
current IEE wiring and building regulations.

INSTALLATION:

Choose the locati on for your new tting
according to the conditio ns listed opposite.

Suitable for outdoors (IP54)

Switch o the mains befor e commencing
installation and remove the appropriate circuit
fuse or lock o MCB.

01) Prepare the xing surface.

02) Fixing holes must be clear of any ob structions
within the mounting sur face (e.g. cables of gas
and water pipes).

03) Unscrew the base and remove.

04) Feed the incoming mains c able through the
base of the tting .

05) Connect the incoming mai ns supply as
follows:

Incoming EARTH (green/yellow) to ear th
terminal with green a nd yellow wire attached

Incoming LIVE (brown/red) to live termi nal
with brown wire att ached

Incoming NEUTRAL (blue/black ) to neutral
terminal with blue wi re attached

06) Secure the base to the sur face mounting
plate.

07) Secure housing to the bas e.

08) Restore power and s witch on.

LAMP REPLACEMENT:

The light source cont ained in this luminaire
shall only be rep laced by the manufacturer,
service age nt or a similar qualied pers on.

CAUTION, RISK OF ELECTRIC SHOCK.

The light source is designed to last the lifetime of the
luminaire.

Fixing kit supplied

Surface
mounting
plate

J bolts

NEUTRAL

(Power Cable)

EARTH

(Power Cable)

LIVE

(Power Cable)

N L

Yellow/Green

Blue

Brown