Eterna HL60B, HL60WH Installation Instructions Manual

Model:

HL60B / HL60WH

Half Lantern

These instructions are provided as a guideline to assist you.

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION

AND RETAIN FOR FUTURE REFERENCE

INSTALLATION INSTRUCTIONS

A guide for qualied electricians

Pack contents:

• Half lantern

• Mounting xtures

LAMP REPLACEMENT:

Switch o the elec tricity at the mains.

Undo the screws at th e top and bottom of the ttin g
and lift o the f ront.

Remove and replace lamp.

Replace the fro nt of the tting and tighten the t wo
screws.

REPLACEMENT LAMP TYPE:

Requires 1 x suita ble ES energy saving lamp (not
included).

Fitting is rated a t 60W max.

CLEANING:

Clean this light t ting only with a soft dr y cloth.

Do not use any chemic al or abrasive cleaners.

EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:

Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Direc tive” eective August 20 05—UK
WEEE Regulation s eective 2nd January 20 07).
Environment Agenc y Registered Producer : WEE/
GA0248Q Z.

WHEN YOUR PR ODUCT COMES TO TH E END OF
ITS LIFE OR YO U CHOOSE TO REPLACE I T, PLEA SE
RECYCLE IT W HERE FACILITIES E XIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.

IF YOU EXPERIENCE PROBLEMS:

If you believe your p roduct is defective, p lease return
it to the place where yo u bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, bu t may not be able to give specic
instructions regarding individual installations.

874/2012

MODELNO.

HL60 Range

Issue 2013

FOR PRODUCT ADVICE:

• T: 01933 673 144

• F: 01933 678 083

• E: [e-mail]

Visit our website:

www.eterna-lighting.co.uk

READ THIS FIRST:

Check the pack and m ake sure you have all of the
parts liste d on the front of this bookle t. If not,
contact the outlet where you bought this product.

This produc t must be installed by a compet ent
person in accord ance with the current building a nd
IEE wiring regulations.

As the buyer, install er and/or user of this product it
is your own responsi bility to ensure that this tt ing
is t for the purpo se for which you have intended
it. Eterna Lightin g cannot accept any liability fo r
loss, damage or premature failure resulting from
inappropriate use.

This product is designed and constructed according
to the principles o f the appropriate British Stan dard
and is intended fo r normal domestic ser vice.

The lifetime of co mpact uorescent lamps an d
ballasts are ne gatively aected by incr eased
switching i.e. wh ere a PIR is being used to control the
tting.

This light ttin g must be installed in accorda nce with
the Building Re gulations. These may be obta ined
from HMSO or viewed and downloaded from www.
communities.go v.uk following the link for Building
Regulations.

Switch o the mains be fore commencing installati on
and remove the appropriate circuit fuse.

Suitable for outdoor use.

This produc t is suitable for installatio n on surfaces
with normal ammability, e.g. wood, plasterboard,
masonry. It is not sui table for use on highly
ammable sur faces (e.g. polystyren e, textiles).

Before makin g xing hole(s), check that there are no
obstructi ons hidden beneath the mount ing surface
such as pipes or cab les.

The chosen loc ation of your new tting shou ld allow
for the produc t to be securely mounted and s afely
connected to th e mains supply (lighting circuit).

If the location o f your new tting requires th e
provision of a new el ectrical supply, the suppl y
must conform with the requirements of the Building
Regulations.

This produc t is designed for permanent co nnection
to xed wiring: this s hould be either a suitable
lighting circuit (p rotected with a 5 or 6 Amp MCB or
fuse) or a fused spu r (with a 3 Amp fuse) via a fused
connection u nit. We recommend that the suppl y
incorporates a s witch for ease of operation .

Make connecti ons to the electrical supp ly in
accordance with the f ollowing code:
Live - Brown or Red
Neutral - Blue or B lack

This tting is d ouble insulated, do not connec t any
part to eart h.

You are advised at ever y stage of your installatio n to
double-check any electrical connections you have
made. After you h ave completed your installatio n
there are elec trical tests that should b e carried out:
these tests are sp ecied in the Wiring Reg ulations
(BS7671) refer red to in the Building Regulati ons.

INSTALLATION:

01) Undo the screws at the top and bot tom of the
tting and lif t o the front.

02) Undo the screw in the plas tic cover at the bottom
of the lamphold er and prize o the cover.

03) Using the back of the tt ing as a template, mark
the location of t he xing holes.

04) Pierce the rubbe r grommet in the back of the
tting. Make th e hole as small as possible so that
a good watert ight seal is maintained when th e
cable has been threaded through.

05) Thread the cabl e through the grommet.

06) Secure the t ting to the wall using xings
(supplied). If the x ings supplied with your t ting
are not appropriate to your installation, select
suitable alternatives.

07) Make the connecti ons to the lampholder
according to the colour code.

08) Replace the cover on th e bottom of the
lampholder and tighten the screw.

09) Insert suita ble ES energy saving lamp.

10) Replace the front of the t ting and tighten the
screws.

11) Restor e the power and switch on.