Eterna HD900W Installation Instructions Manual

SAFETY AND INSTALLATION

INSTRUCTIONS

Model:

High Pressure 900W Hand Dryer

HD900W

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING YOUR NEW

HAND DRYER. PLEASE RETAIN FOR FUTURE REFERENCE

Pack Contents

Hand dryer
Fixing pack

This hand dryer uses a high speed
motor to force air out of the outlet vent
at around twice the speed of a normal
hand dryer. The extra air velocity means
that less heat is required to dry hands
effectively and so this hand dryer
typically uses less than half the energy
of a standard type.

Safe

The hand dryer is protected against
over heating, prolonged operation and
over-current.

Automatic

The dryer starts automatically when
hands are moved within 10cm of the
outlet vent and will stop 1s after the
hands have been removed

Durable

The case is cast in lightweight but
strong aluminium in a shape designed
for resistance to vandalism.

Safe

Automatic

Durable

Energy Saving

General Information and Safety Instructions

Read this first

Check the pack and make sure you have all of
the parts listed on the front of this booklet. If
not, contact the outlet where you bought this
product.

This hand dryer must be installed by a
competent person in accordance with the
Building Regulations making reference to the

current edition of the IEE Wiring Regulations
(BS7671). The Building Regulations may be
obtained from OPSI (Office for Public Sector
Information) or the department of Communities
and Local Government and viewed and
downloaded from www.communities.gov.uk
following the link for Building Regulations.

As the buyer, installer and/or user of this
product it is your own responsibility to ensure
that this hand dryer is fit for the purpose for
which you have intended it. Eterna Lighting
cannot accept any liability for loss, damage or
premature failure resulting from inappropriate
use.

If in any doubt, consult a qualified electrician.

Switch off the mains before commencing
installation and remove the appropriate circuit
fuse.

Disconnect the dryer from the electrical supply
before flash or high voltage testing.

Suitable for indoor use only.

This product is suitable for installation on
surfaces with normal flammability (indicated by
the “F” in a triangle) e.g. wood, plasterboard,
masonry. It is not suitable for use on highly
flammable surfaces (e.g. polystyrene, textiles).

Before making fixing hole(s), check that there
are no obstructions hidden beneath the
mounting surface such as pipes or cables.

The chosen location of your new hand dryer
should allow for the product to be securely
mounted and safely connected to the mains
supply.

This product is designed for permanent
connection to fixed wiring: this should be
either a suitable circuit (protected with a 5 or
6 Amp MCB or fuse) or a fused spur (with a
5 Amp fuse) via a fused connection unit. We
recommend that the supply incorporates a
double pole switch.

Do not cover the hand dryer.

The dryer should be located where it cannot be
splashed.

The dryer must be positioned so that there is at
least 0.4m (400mm) between the outlet vent
and any surface below.

Do not attach to surfaces which are damp,
freshly painted or otherwise electrically
conductive (e.g. metallic surfaces).

If the location of your new hand dryer requires
the provision of a new electrical supply, the
supply must conform with the requirements of
the Building Regulations making reference to
the current edition of the IEE Wiring Regulations
(BS7671).

Make connections to the electrical supply in
accordance with the following code:
Live - Brown or Red
Neutral - Blue or Black
Earth - Green and Yellow

When making connections, ensure that the
terminals are tightened securely and that
no strands of wire protrude. Check that
the terminals are tightened onto the bared
conductors and not onto any insulation. Wrap
loose terminal blocks well with insulating tape.

This product must be connected to Earth.

You are advised at every stage of your
installation to double-check any electrical
connections you have made. After you have
completed your installation there are electrical
tests that should be carried out: these tests are
specified in the Wiring Regulations (BS7671)
referred to in the Building Regulations. If in
doubt, consult a qualified electrician.

There are no user serviceable parts inside, if
your hand dryer develops a fault or does not
function correctly, it must be repaired by a
suitably qualified person

This product is not intended to be used by
children and persons with sensory, physical
and/or mental impairments that would prevent
them from using it safely.

Small children should be supervised to ensure
that they do not play with this appliance.

2