Eterna FL124B Installation Instructions Manual

Issue 2013

Model:

FL124B

23W Low Energy Floodlight

These instructions are provided as a guideline to assist you.

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION

AND RETAIN FOR FUTURE REFERENCE

Pack contents:

1 x Fitting

1 x 23W ES CFL lamp

FOR PRODUCT ADVICE:

• T: 01933 673 144

• F: 01933 678 083

• E: [e-mail]

Visit our website:

www.eterna-lighting.co.uk

INSTALLATION INSTRUCTIONS

A guide for qualied electricians

874/2012

A

MODELNO.

FL124B

MODELNO.

A

++

XXX kWh/1000h

22.50

CFL23W

A

EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:

Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Direc tive” eective August 20 05—UK
WEEE Regulation s eective 2nd January 20 07).
Environment Agenc y Registered Producer : WEE/
GA0248Q Z.

WHEN YOUR PR ODUCT COMES TO TH E END OF
ITS LIFE OR YO U CHOOSE TO REPLACE I T, PLEA SE
RECYCLE IT W HERE FACILITIES E XIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.

CLEANING:

Disconnect t he power and clean the exte rior only of
this tting wit h a moist (not wet) cloth.

Do not use any chemic al or abrasive cleaners.

IF YOU EXPERIENCE PROBLEMS:

If you believe your p roduct is defective, p lease return
it to the place where yo u bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, bu t may not be able to give specic
instructions regarding individual installations.

For breakage inf ormation visit:
www.eterna-lighting.co.uk

LAMP SPECIFICATIONS:

Voltage 220-240V

Frequency 50Hz

Nominal lumens

1371 lm

Wattage 23W

Nominal life time of the lamp 10,000 hrs

Number of switching cycles
before premature lamp
failure

30,000

Colour temperature 6400K

Warm-up time up to 60 % of
the full light output

40s

Dimmable No

Lamp dimensions (mm) 140 x 59

Lamp mercury content to an
accuracy of 0.1mg

2.5

Cap type ES (E27)

Rated Wattage 22.5W

Rated luminous ux 1371 lm

Rated lamp lifetime 10,000

Colour rendering index Ra 80%

Lamp power factor 0.55

Lumen maintenance factor at
end of nominal life

50%

Starting time 0.9s

READ THIS FIRST:

Check the pack and m ake sure you have all of the
parts liste d on the front of this bookle t. If not,
contact the outlet where you bought this product.

This produc t contains glass, care must be take n when
assembling, t ting or handling to prevent per sonal
injury or damag e to the product.

This light ttin g must be installed by a compe tent
person in accord ance with the Building Regulat ions
making refere nce to the current edition of the
IEE Wiring Regu lations (BS7671). The Buildin g
Regulations may b e obtained from HMSO or view ed
and downloaded from www.communities.gov.uk
following the lin k for Building Regulations .

As the buyer, install er and/or user of this product it
is your own responsi bility to ensure that this tt ing
is t for the purpo se for which you have intended
it. Eterna Lightin g cannot accept any liability fo r
loss, damage or premature failure resulting from
inappropriate use.

The lamps (bulbs/tubes) supplied with this tting are
consumable par ts and therefore may be out side of
any warranty oered.

Switch o the mains be fore commencing installati on
and remove the appropriate circuit fuse.

When working at h eights, please use a suita ble
platform.

Disconnect t he tting from the elec trical supply
before ash or hi gh voltage testing.

Suitable for indoor and outdoor use.

This produc t is suitable for installatio n on surfaces
with normal ammability e.g. wood, plasterboard,
and masonry. It is not s uitable for use on highly
ammable sur faces (e.g. polystyren e, textiles).

Before makin g xing hole(s), check that there are no
obstructi ons hidden beneath the mount ing surface
such as pipes or cab les.

The chosen loc ation of your new tting shou ld allow
for the produc t to be securely mounted and s afely
connected to th e mains supply (lighting circuit).

When choosing th e location for your new tt ing,
ensure that the xin gs will be anchored in a solid
surface e.g. con crete, brick or a joist—do not  x
directly onto panelling, cladding, plasterboard etc.

If the location o f your new tting requires th e
provision of a new el ectrical supply, the suppl y
must conform with the requirements of the Building
Regulations mak ing reference to the current e dition
of the IEE Wiring Re gulations (BS7671).

This produc t is designed for permanent co nnection
to xed wiring: this s hould be either a suitable
lighting circuit (p rotected with a 5 or 6 Amp MCB or
fuse) or a fused spu r (with a 3 Amp fuse) via a fused
connection unit.

We recommend that the s upply incorporates a
switch for ease of o peration.

Make connecti ons to the electrical supp ly in
accordance with the f ollowing code:

Live - Brown or Red
Neutral - Blue or B lack
Earth - Gree n and Yellow

When making con nections, ensure that the te rminals
are tightened se curely and that no strands of wi re
protrude. Chec k that the terminals are tightene d
onto the bared cond uctors and not onto any
insulation.

This produc t must be connected to Ear th.

IMPORTANT: Always switch o  at the mains before
changing the lamp.

You are advised at ever y stage of your installatio n to
double-check any electrical connections you have
made. After you h ave completed your installatio n
there are elec trical tests that should b e carried out:
these tests are sp ecied in the Wiring Reg ulations
(BS7671) refer red to in the Building Regulati ons.

INSTALLATION:

01. Choose the location for yo ur new oodlight
giving consideration to all of the conditions listed
above.

02. Using the xing str ap as a template, mark the
position for the xing holes on your mounting
surface.

03. Prepare your mounti ng surface as appropriate fo r
your chosen xin gs (not supplied). Use a spirit
level to ensure the t ting will be level.

04. Secure the  tting in place.

05. Loosen the bolt s at each end of the xing strap
and adjust the ang le of your oodlight to give the
desired spread of light.

06. Tighten the b olts to lock your oodlight i n
position.

07. Make the connections to your mains su pply as
described in th e “Read this rst” sec tion.

08. Using a cross-h eaded screwdriver, undo the
screws that secur e the diuser and allow to hang
down.

09. Fit the uorescent la mp.

10. Replace the diuser a nd tighten the screws
making sure that the wat erproof gasket is
correctly positioned and compressed.

11. Press the trim back o nto the front of the tting
making sure the sl ots used for removal are at the
bottom.

12. Restore the power and s witch on.

LAMP REPLACEMENT:

01. Switch o the electricit y at the mains.

02. Us ing a cross-headed screwdr iver, undo the
screws that secur e the diuser and allow to hang
down.

03. Remove the lamp.

04. Insert new lamp.

05. R eplace the diuser and sec ure in position
making sure that th e gasket is correctly
positioned and compressed.

06. Restore th e power and switch on.

REPLACEMENT LAMP TYPE:

Fitting requi res 1 x 23W ES helical CFLi 6400K
(included) or energy saving alternative.

Fitting is rated a t 23W max.