Eterna D041, D042, D043, D045 Installation Instructions

SPECIFICATIONS:

Nominal useful luminous ux

Rated Wattage 20W

Rated luminous ux 260 lm

Nominal life time of the lamp 2,000 hrs

Colour temperature 2700K

Number of switching cycles
before premature lamp
failure

Warm-up time up to 60 % of
the full light output

Dimmable Yes

Lamp dimensions (mm) 28 x 10

Nominal beam angle <120°

Rated power 20W

Rated lamp lifetime 2,000

Lamp power factor 1

Lumen maintenance factor at
end of nominal life

Starting time 0.2s

Colour rendering 100%

Rated peak intensity 320cd

Rated beam angle <120°

260 lm

10,000

Instant full light

70%

D041-45

MODELNO.

A

XXX kWh/1000h

21.2

B

++

874/2012

D041-45

MODELNO.

B

INSTALLATION INSTRUCTIONS

A guide for qualied electricians

EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:

Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.

WHEN YOUR PRODUC T COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.

Issue 2013

FOR PRODUCT ADVICE:

• T: 01933 673 144

• F: 01933 678 083

• E: [e-mail]

CLEANING:

Clean this light tting only with a soft dr y cloth.

Do not use any chemical or abrasive cleaners.

IF YOU EXPERIENCE PROBLEMS:

If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.

For breakage information visit:
www.eterna-lighting.co.uk

Visit our website:

www.eterna-lighting.co.uk

Pack contents:

1 x Fitting
1 x G4 M47 20W capsule lamp
1 x Mini plug
1 x Fixing kit

Model:

D041 / D042 / D043 / D045

Low Voltage Surface / Recessed Capsule Downlights

These instructions are provided as a guideline to assist you.

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION

AND RETAIN FOR FUTURE REFERENCE

READ THIS FIRST:

Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.

This product contains glass, care must be taken when
assembling, tting or handling to prevent personal
injury or damage to the product.

This product must be installed by a competent
person in accordance with the current building and
IEE wiring regulations.

As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this tting
is t for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.

This product is designed and constructed according
to the principles of the appropriate British Standard
and is intended for normal domestic ser vice. Using
this tting in any other environments may result in
a shortened working life, for example where there
is prolonged periods of use or higher than normal
ambient temperatures such as lighting public or
shared spaces or in nursing / care home facilities.

Suitable for indoor use only.

This product is only suitable for use in living areas
(not for areas constantly subject to moisture).

This product is suitable for installation on surfaces
with normal ammability (indicated by the “F” in a
triangle) e.g. wood, plasterboard, masonry. It is not
suitable for use on highly ammable surfaces (e.g.
polystyrene, textiles).

Use only with a suitable 240V / 12V step down
transformer.

Do not connect lights directly to the mains.

Do not overload the transformer, check that the total
Wattage of all ttings does not exceed the maximum
marked on the transformer.

Before making xing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.

Make sure that the xings are strong enough to
support the considerable weight of the tting and
hold it rigidly.

If the location of your new tting requires the
provision of a new electrical supply, the supply must
conform with the requirements of the latest edition
of the IEE wiring regulations.

Do not cover the t ting and / or transformer with any
insulating materials.

This tting uses SELV (Safety Extra Low Voltage). Do
not connect any part to ear th.

The tting must be positioned so that there is at least

0.3M (300mm) between the bulb and any illuminated
surface.Do not use the tting without the safety
shield tted.

When replacing the lamp, do not touch with bare
ngers, grip the lamp with a tissue or clean sof t cloth.

Do not attach to surfaces which are damp, freshly
painted or otherwise electrically conductive (e.g.
metallic surfaces).

LAMP REPLACEMENT:

IMPORTANT!

Never touch the glass when the light is switched on.
Allow light to cool before changing the bulb. Switch
o the electricity at the mains.

Remove the glass diuser by prizing the metal ring
that retains it out of the tting using a small at
bladed screwdriver.

Pull the old lamp straight out of its socket and
replace only with one of the same type and rating.

IMPORTANT!
Do not touch the lamp with bare ngers, use a soft
clean cloth or tissue.

Replace the glass diuser pressing rmly back into
place.

REPLACEMENT LAMP TYPE:

Wattage: This tting is rated at 20W max
Supply Voltage: 12V
Type: G4 M47 capsule

ASSEMBLING THE PLUG:

Once you have threaded the cables from your light
to your transformer, you will need to push the pins at
the ends of your cables into the plug body.

Note: once the pins have been inserted they cannot
be removed.

INSTALLATION:

01) Check that the transformer you intend to use to
power your tting is adequately rated for the
total number of ttings you are installing and that
it has been installed in accordance with all of the
manufacturers instructions.

02) Choose the location for your new tting.

03) Prepare the route for the cable between the light
and the transformer.

04) Extract the light from its surround by gently

levering it out using a small screwdriver or other
at bladed implement. Take great care not to
damage the decorative nish.

05) FOR SURFACE MOUNTING: With the cable
threaded through the surround, secure the
surround in position using suitable xings
appropriate to the mounting surface.

FOR RECESSED MOUNTING: Make a hole in the
mounting sur face of 61mm diameter.

06) Gently pull the cable through your prepared exit

route and press the light tting back into the
surround. Make sure that you do not trap a loop
of cable behind the light tting.

Hole cut
out size:

61mm

diameter

07) Make the connec tion of the cable to the
transformer. We recommend the use of an Eterna
Lighting transformer which has sockets designed
to allow the plug tted to your light to plug
directly in.

Note: If you have any other transformer in which
there is no provision for connection using the
plug tted to your light, you will need to cut
the plug o and use an alternative method
of connection. The connections to the light
tting are not designated Live or Neutral. Make
connections using a terminal block, ensure that
there are no strands of wire protruding and wrap
well with insulating tape.

08) Restore the power and switch on.

Prize out
glass and ring
with a at
blade