This mobile phone complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not caus e
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This mobile phone has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiated radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television recept i on , whi ch can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
RF Exposure Information (SAR)
4
This model phone meets the government’s requirements for exposure to
radio waves.
This phone is designed and manufactured not to exceed the emission
limits for exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. G overnment.
The exposure standard for wireless mobile phones employs a unit of
measurement known as the Specific Absorption Rate, or SAR. The SAR limit
set by the FCC is 1.6W/kg.
*
Tests for SAR are conducted using standard
operating positions accepted by the FCC with the phone transmitting at its
highest certified power level in all tested frequency bands. Although the SAR
is determined at the highest certified power level, the actual SAR level of the
phone while operating can be well below the maximum value. This is
because the phone is designed to operate at multiple power levels so as to use
only the poser required to reach the network. In general, the closer you are to
a wireless base station antenna, the lower the p ower output.
The highest SAR value for the model phone as reported to the FCC
when tested for use at the ear is 1.18
bed in this user guide, is 1.098 W/kg (Body-worn measurements differ
descri
among phone models, depending upon available enhancements and FCC
requirements.)
While there may be differences between the SAR levels of various
phones and at various positions, they all meet the government requirement.
9 W/kg and when worn on the body, as
The FCC has granted an Equipment Authorization for this model phone
with all reported SAR levels evaluated as in compliance with the FCC RF
exposure guidelines. SAR information on this model phone is on file with
the FCC and can be found under the Display Grant section of
http://www.fcc.gov/oet/fccid
For body worn operation, this phone has been tested and meets the FCC
RF exposure guidelines for use with an accessory that contains no metal and
the positions the handset a minimum of 1.5 cm from the body. Use of other
enhancements may not ensure compliance with FCC RF exposure guidelines.
If you do no t use a body-worn accessory and are not holding the phone at the
ear, position the handset a minimum of 1.5 cm from your body when the
phone is switched on.
after searching on FCC ID: SPUX650.
Safety Instructions
Please Read Before Proceeding.
U
Avoid heavily pressing on the touch screen.
U
Avoid heavily pressing on the touch screen with the stylus or your fingers.
U
This product is not charged when shipped from the factory.When you use
U
this product the first time, we recommend that you install the battery as
illustrated and fully charge it for about 8 hours before use.
Before you install the SIM card, make sure that tap the
U
in
Wireless Manager
Bluetooth, and wireless LAN functions. And press the “Power Button” of
the Pocket PC to turn off the screen. Otherwise, abnormal disconnection
problems will occur.
When you are on a plane, in a medical facility or at a gas station where
U
wireless communications devices are not allowed and must be turned off,
please go to
off your Pocket PC’s mobile phone, Bluetooth, and wireless LAN
functions. By pressing the “Power Button” of the Pocket PC, you only
turn off the display.
In case the Pocket PC is damaged, send it back to the dealer for repair.Do
U
not attempt to disassemble the Pocket PC on your own; otherwise the
warranty will be void.
Wireless Manager
to turn off your Pocket PC’s mobile phone,
and select the
ALL OFF
ALL OFF
Button to turn
Button
Where to Find Information
For information on: See this source:
Programs on your Pocket PC This User’s Guide and Pocket PC Help. To
view Help, tap
Additional programs that can
be installed on the Pocket PC
Connecting to and
synchronizing with a desktop
computer
Up-to-date information on
your Pocket PC
This document lists the functions, specifications, and illustrations for
reference only. The actual purchased product should be taken as the
standard.
The Pocket PC Getting Started CD.
Check the user’s guide that comes with this
product or look for the online help relevant
to synchronization tools on the desktop PC
or the Pocket PC.
http://www.microsoft.com/windowsmobile/
and then
Help
.
UUsseerr MMaannuuaall
REGULATIONS
FCC
AFETY INSTRUCTIONS
S
HERE TO FIND INFORMATION
W
GETTING STARTED /...........................................................1-1
Turn off phone if it is on
Turn on phone if it is off
1-4
5
k
Using the Pocket PC for the First Time
If you are opening this product for the first time, the main battery and
the Pocket PC are packed separately inside the product package.
Get your Pocket PC ready to go
Insert the SIM card into the SIM
1.
card slot with its golden contacts
facing down. Follow the picture
indicated on the Pocket PC.
Back cover
3.
Main battery lock
5.
Main battery
2.
Follow the direction in the
4.
illustration to install the main
battery.
Installing the SIM Card
Installing the Battery
4
1 2
3
Unloc
Lock
Getting Started 1-5
Charging Power and Power Supply
Connect the AC adapter plug to any household power outlet.
n
Connect the other plug from the AC adapter to the USB port. The Pocket
o
PC starts to charge automatically.
If you need to connect Pocket PC and desktop computer, you could
p
connect the USB cable to the USB port. And then connect the other end
of the USB cable to the USB port on the desktop computer. Your Pocket
PC will also charge at the same time.
1-6
n
o
p
It will take about 8 hours to fully charge the battery after the first time you
1.
open the package. Subsequent charging will only take about 3 hours.After
charging, you can disconnect the AC adapter and carry the Pocket PC
around portably.To maintain smooth operation, charge the power regularly.
View the battery icon
2.
on the upper right corner to check the power
usage condition.
The LED indicator on the upper right of Pocket PC will display the
3.
charging and function usage status.
Red always light: Device is charging.
Red sparkling once every 4 sec: Warning of Battery low level.
Red
Red sparkling twice repeatedly: Warning of Battery critical
situation.
Red sparkling continuously: Bat tery cover not on or Battery
level very low.
Green always light: Battery charging is full.
Green
Green sparkling once every 4 sec: GSM is connecting on line.
The LED indicator on the upper left of Pocket PC
4.
Blue
Blue sparkling once every 4 seconds: Bluetooth enable
Amber
White
Amber sparkling once every 4 seconds: WLAN enable
White sparkling once every 4 seconds: GPS enable
Getting Started 1-7
Re-installation or Replacing the Battery
If the phone, GPRS or wireless LAN connection function is already
activated, deactivate it first and then replace the battery.
Slide and remove the back cover of Pocket PC.
1.
You may poke down to unlock the main battery lock in order to remove the
2.
battery.
Replace the main battery and lock it properly. When you remove the main
3.
battery, your Pocket PC will enter the sleep mode.
Slide the back cover into the groove, and reinstall the back cover.
4.
1-8
Power On and Off
Power Button
Sleep Mode
Press the “Power Button” of the Pocket PC to enter the Sleep mode.At this
1.
time, the screen is turned off and all peripheral devices enter the
power-saving mode.But if the phon e is turned on, it is still in the call
waiting mode.
To turn on the screen later, just press the “Power Button.”
2.
Tap
3.
Power
to set the device to turn off
automatically after waiting for a
certain time period.
,
Settings
and then the
, the
System
Advanced
tab,
tab
Getting Started 1-9
Turn on the Screen
This product is designed with a power-saving feature.If the screen is
turned off, press the “Power Button” of the Pocket PC to turn it on.
If the screen is too dark and you
cannot see clearly, set the proper
brightness level for the backlight.
Tap
Backlight
Level
Using the Stylus to Touch the Screen
Your Pocket PC is designed for graphics-based operation. Generally
speaking, we usually “use the stylus to perform basic actions such as tap,
drag, and tap and hold” on the touch screen. Other actions such as reset
and cold boot will require the use of the stylus tip.
Pull the stylus to full-length to make it easier to tap the screen during
operation. When kept completely in the stylus holder, the stylus length
shortens.
Avoid heavily pressing on the touch screen with the stylus or your
,
Settings
and then the
tab.
, the
System
Backlight
tab,
fingers.
1-10
Restarting the Pocket PC
Appropriate situation: If the Pocket PC is unable to maintain normal
operation, has no response, or if the screen is frozen.
For your consideration, factoring into your safety and convenience,
please refer to the following instructions in order:
Reset
1.
Default Settings
2.
procedures
Clean Boot
3.
Press the “Reset Button” of Pocket PC with the
tip of the stylus.
If the touch screen is functional, please tap
Programs, Utilities
Hold the “Power Button” and press once on the
“Reset Button” with the tip of the stylus, and
release both buttons simultaneously. Next,
continually hold the End Button
system inquiry screen is displayed, then release
the End Button. Press Soft-Key to answer the
question.
, and then
Default Settings
until the
,
.
Getting Started 1-11
Reset method: Press the “Reset
V
Button” of Pocket PC with the tip of
the stylus.
Reset
Appropriate situation: If the Pocket PC is unable to maintain normal
V
operation, has no response, or if the screen is frozen.
Result: In a moment, when Pocket PC automatically completes the system
V
startup process, the last display will be the Today screen. This will retain
the Microsoft Windows, factory pre-installed applications, user’s inpu t
data, newly installed programs, and user custom settings.
1-12
Default Settings
Tap ,
Appropriate situation: If the Pocket PC is unable to maintain normal
V
operation, but the touch screen is functional. Please refer to the
instructions in this section to troubleshoot.
Result: This will retain only the Microsoft Windows, and factory
V
Programs, Utilities
, and then
Default Settings
If this application is inadvertently
1.
accessed, please select the
the upper right of the screen to exit,
the system will not be affected.
If you are certain that you wish to
2.
perform this action, please select
the data input block on the right,
and enter the authorized code in the
block to the left. Then tap the OK
button.
.
to
pre-installed applications. Other settings such as user’s input data, newly
installed programs, and user custom settings will all be cleared.
Getting Started 1-13
Clean Boot
Cold boot method: Hold the “Power
V
Button” of the Pocket PC with one
hand while holding the stylus tip to
push in the “Reset Button” with the
other. Simultaneously release both the
“Power Button” and “Reset Button”.
Appropriate situation: If a previous reset has already been attempted and
V
the Pocket PC is still unable to maintain normal operations, has no
response, or if the screen is frozen.
Before executing the preceding “Cold boot method”, please carefully
V
consider the following instructions and then decide on the cold boot
method.
After a cold boot is performed, if no buttons are pressed, when Pocket PC
1.
automatically completes the system startup process, the last display will be
the Today screen. This is identical to the reset result.
If a previous reset has already been attempted but the Pocket PC is still
2.
unable to maintain normal operation, consider the following solution:
After cold boot, hold the End Button
PC until the system inquiry screen is shown, and then release the End
Button. Next, please read thoroughly through the instructions on cold
booting before continuing carefully.
on the bottom right of Pocket
1-14
Perform cold boot and hold the End Button . Please refer to the
following instructions before careful consideration.
Erase all data and load default?
Á
The default is “No.” If Yes or No was not
selected, after a few seconds the system will
automatically execute the default No.
If you long press Left Soft-Key for a few
seconds to select “Yes,” then the system will
erase all data and load default. After your
Pocket PC restarts, follow the instructions on
the screen to complete.
Caution!
After performing a cold boot, the system will retain Microsoft Windows
1.
and pre-installed programs. If you answer “Yes” to the question displayed
after a cold boot, other items such as the user’s input data, newly installed
programs and user settings will be lost.
There are two ways to retain your data, loaded default and registry:
2.
Perform a Reset
n
Performing a Cold Boot, and answer “No” when the above question
o
displays.
.
Getting Started 1-15
1-16
Loading...
+ 218 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.