Etec E580TM Installation Manual

Tilting LCD/Plasma Flat Panel

Wall Mount

Installation Guide

Model: E580TM

• Easy installation

• Low prole

• Built-in level for easy positioning

• Safety bolts lock the TV on the mount

• Easy to adjust tilt angles:

-5 to 15 degrees

• Supports most 36” - 63” LCD/Plasma Flat Panels

• Maximum weight capacity: 176 lbs.

• Supports VESA Sizes up to 700X500

This product is intended only to mount a television of the indicated size and weight.
Using this product to mount televisions heavier than the maximum weight capacity can
damage equipment and cause personal injury.

READ THIS FIRST
Read this entire manual! Do not attempt to install this product if you do not understand the

instructions. Contact a qualied mount installer if you have any doubts about a safe and
secure mount installation, or if you are not sure what specic wall materials you are at-

taching this mount to. Check all the parts carefully to make sure there are no missing
or damaged parts. Improper installation may result in damage to your TV, property, and
personal injury.

This product is intended only to mount a television of the indicated size and weight. Using this
product to mount televisions heavier than the maximum weight capacity can damage equipment
and cause personal injury.

Schoenfeld International Inc. and ETEC USA are not responsible for personal injury or
product damage due to mishandling, incorrect mounting, incorrect assembly, or incorrect use of

this product.

CHILD SAFETY

How and where you use your television wall mount is extremely important for Child Safety
As you set up and use your new product, keep all of these safety tips in mind.

• One size of TV wall mount does not t all TVs. Use only a TV wall mount rated for the weight of
your TV and the size of your screen. Your TV wall mount assembly instructions contains spe­cic information on the maximum weight and screen size combination that your wall mount can

safely support. Do not exceed the maximum weight of screen size for any TV wall mount.

• Carefully read all of enclosed instructions for proper use of this product. If you have any doubts
about safe and secure assembly, please contact a professional.

• Don’t let children climb on or play with mounts or TVs.

• Remember that children can become excited while watching a program, especially on a “larger
than life” TV. Make sure to place or install the TV wall mount where it cannot be pushed, pulled

on, or knocked down.

• Make sure that you route all cords and cables so that they cannot be pulled or grabbed by curi­ous children.

Always wear safety goggles to when drilling or installing hardware.

Tools

For your convenience, we have included an allen wrench and a socket tool with this mount. For the best
assembly experience and mounting safety, we always recommend using full-size tools for each assem­bly steps.

Below is a recommended tool list you will need for proper and safe installation. See applicable warnings
in this manual about certain types of mounting surface materials and the special hardware and tools that
should be used.

• Drill with a specic size drill bit to pre-drill holes in the wall

• Stud nder

• Tape measure

• Pencil

• Screw drivers

• Socket wrenches

• Small hammer

• Safety goggles

The actual appearance and quantity of parts may be different than shown in the illustration. Consult
the table for actual quantities.

3

Step 1: Attach the left and right brackets to your TV

Do not force the bolts into the mounting holes on your TV. Do not use an electric drill to tight­en these bolts on your TV. This could damage the equipment or cause personal injury.

CAUTION: Do not place the TV face down on a hard surface when installing the mounting plate

on the TV. Placing the TV face down on a hard surface can result in equipment damage. Use a

blanket or other suitable surface.

Check your TV manual to conrm the required bolt diameter according to the size, depth, and position
of the mounting holes in your TV.

For correct installation, install the brackets with the hook on each bracket facing down

Install the bolts, spacers, and square washers in accordance with the following:

If your television has a straight back, spacers are not required. Use the selected bolts (A-F) and
square washers (I) to install the bracket directly on the back of the television as shown in Fig 1a. Make
sure that the two brackets are equal in height and are level. Once the brackets are aligned, securely
tighten the bolts..

4

Fig. 1a