Etdoor ET-600E, ET-800E, ET-1000E Installation Instructions And User Manual

Sectional and Tilting Door Opener

Installation Instructions and User Guide

ET-600E
ET-800E
ET-1000E

S/N

WARNING

Please read the manual carefully before installation and use. The installation of your
new door opener must be carried out by a technically qualified or licensed person.
Attempting to install or repair the door opener without suitable technical qualification
may result in severe personal injury, death and / or property damage.

CONTENTS

Important Safety Recommendations...…………………………….……………………………..1-2

Basic function introduction……………………………………………………………………….....2

Special function introduction………….……………………..……………………………………..2

Installation (aluminum track)………………………………………….…………………………..3-4

Installation (steel track)………………………………………….…………………………….…….5

Installation (sectional steel track)………………………………………………………………..6-9

Installation recommendations……………………………………………………………………..10

Basic function setting and applying……………………………………………………………..11-12

Special function introduction and application………………………………………….……….13-14

PCB structure………………..…………………………………………………………..……….. 14

Aluminum, steel & sectional steel accessory list…………………..…………………….……...15

Manual disengagement…………………………………………………………………………….16

Maintenance………………………………………………………………………………………...16

Technical specifications…………………………………………………………………………….17

Final note….………………………………………………………………………………………...17

Important information for the user………………………………………………………………...17

Important safety recommendations

FAILURE TO COMPLY WITH THE FOLLOWING SAFETY RECOMMENDATIONS MAY
RESULT IN SERIOUS PERSONAL INJURY, DEATH AND / OR PROPERTY DAMAGE.

1. PLEASE READ CAREFULLY AND ADHERE TO ALL SAFETY AND INSTALLATION

RECOMMENDATIONS.

2. The opener is designed and manufactured to meet local regulations. The installer must be
familiar with local regulations required in respect of the installation of the opener.

3. Unqualified personnel or those persons who do not know the occupational health and
safety standards being applicable to automatic gates and other doors, must in no
circumstances carry out installations or implement systems.

4. Persons who install or service the equipment without observing all the applicable safety
standards will be responsible for any damage, injury, cost, expense or claim whatsoever
any person suffered as a result of failure to install the system correctly and in accordance
with the relevant safety standards and installation manual whether directly or indirectly.

5. For additional safety we strongly recommend the inclusion of Photo Beam. Although the
opener incorporates a pressure sensitive Safety Obstruction Force system the addition of
Photo Beam will greatly enhance the operating safety of an automatic garage door and
provide additional peace of mind.

6. Make sure that the garage door is fully open & stationary before driving in or out of the
garage.

7. Make sure the garage door is fully closed & stationary before leaving.

8. Keep hands and loose clothing off the opener and garage door all the time.

9. The Safety Obstruction System is designed to work on STATIONARY objects only.
Serious personal injury, death and / or property damage may occur if the garage door
comes into contact with a moving object

10. This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.

11. Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or retailer for

recycling advice.

12. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.

- WARNING: Important safety instructions. It is important for the safety of persons to
follow all instructions. Save these instructions.

- Do not allow children to play with door controls. Keep remote controls away from
children.

- Watch the moving door and keep people away until the door is completely opened
or closed.

- Take care when operating the manual release since an open door may fall rapidly
due to weak or broken springs, or being out of balance.

- Frequently examine the installation, in particular check cables, springs and
mountings for signs of wear, damage or imbalance. Do not use if repair or
adjustment is needed since a fault in the installation or an incorrectly balanced door

may cause injury.

- Each month check that the drive reverses when the door contacts a 50 mm high
object placed on the floor. Adjust if necessary and recheck since an incorrect
adjustment may present a hazard, for drives incorporating an entrapment
protection system depending on contact with the bottom edge of the door.

- Details on how to use the manual release.

- Information concerning the adjustment of the door and drive.

- Disconnect the supply when cleaning or carrying out other maintenance.

- The installation instructions shall include details for the installation of the drive and

its associated components.

Basic function introduction

1. Soft start, soft stop
Minimize start-up load on garage door opener and garage door

2．Opening & closing force self-learning
3．Overloading force detecting, the door will reverse more than 15 cm automatically when it is

overloaded when closing.

4. Safety resistance adjustable, with a wide range, sensitive and reliable.（Automatic safety

reverse）
5．Wall switch interface available.
6．Photo beam, the door will change to open when obstruction is detected while closing.
7．Low-voltage protection, the process will not perform any action of opening and closing when

voltage is too low, door panel and controller won’t be damaged.

8．We adopt rolling code transmitter, with billions of codes, won’t be coincident code or pirated

code.
9．Back up battery interface available, in case of power failure.
10．Keypad interface available.
11．With auto-closing feature.

12. Metal bottom plate

13. O/S/C button B, make adjustment, maintenance and emergent opening or closing
convenient.

14. External fuse A.

Special function introduction

The following functions are made to order in accordance with the special needs of
customers:

1. Caution light feature

2. Pass door protection feature

3. Rapidly automatic safety reverse

Referring to Fig. 2 for recommended installation

1) Sectional door rail 5) O/S/C button

2) 24V DC flash light (optional extra) 6) Power socket

3) Wall switch 7) Door opener

4) Photo beam (RX/TX Type)

CHAIN SHUTTLE ASSEMBLY

As for the ease of the chain, it is delivered with the
chain and chain shuttle already assembled in the
track. If you need to assemble it yourself, connect
the chain shuttle to the chain with screw C tightened
firmly. Move shuttle B to half way along the rail
section; grease the chain and sprocket (Fig.3) with
a lithium type grease or equivalent. Do not use oil
type lubricants.

Fig. 6

Fig. 7

Before attaching the motor brackets
(E) (FIG 4) screw an inverted nut
(6mm) (D) on each stud then position
the brackets (E) on the studs and
secure them in-place using a second
6mm-nut and then lock the brackets to
the rail by tightening the inverted lock
nuts (D). Connect the opener edge (G)
to the doorframe or to the ceiling iron
angle (F) (Fig.5), maintaining a
minimum gap of 30mm from the top

panel’s maximum height (Fig. 6).

Check measurements for drilling insert
and lock the brackets F and fix the
opener to the ceiling with the correct
fixings (Fig. 7). Cut off any hanging
brackets excess.
Warning: Make sure the opener is
affixed to noggins in ceiling and not to
plasterboard. Failure to have a safe
and secure fixing will lead to opener
falling, and cause serious persons and
/or property damage.