ETC Source Four Mini LED 50 Degree Installation Guide

ETC Installation Guide

Canopy mount

Track mount

Source Four Mini™ LED Canopy and Track Mount Kits

Introduction

This guide illustrates the installation of the Canopy and Track Mount kits for the
Source Four Mini LED fixture. For additional information, see the Source Four
Mini LED User Manual that shipped with your fixture.

WARNING:

TURN OFF POWER at main fuse or breaker box and verify
that the power is off before proceeding with installation.

Wiring must meet local and national codes.
Do not mount the fixture on or near combustible surfaces.
Do not operate the fixture without a lens installed.
Always hang the fixture with the color frame retaining clip in the

locked position.

Corporate Headquarters
London, UK

 Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK  Tel [phone]  Fax [phone]

Rome, IT 

Via Pieve Torina, 48, 00156 Rome, Italy  Tel [phone]  Fax [phone]

Holzkirchen, DE
Hong Kong  Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong  Tel [phone]
Service:

(Americas) [e-mail] 

Web:

www.etcconnect.com 

7063M2110 

 3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA  Tel [phone]  Fax [phone]

 Ohmstrasse 3, 83607 Holzkirchen, Germany  Tel [phone]  Fax [phone]

Rev A  Released 2014-02  ETC intends this document to be provided in its entirety.

Copyright © 2014 ETC. All Rights Reserved.  Product information and specifications subject to change.

(UK) [e-mail]  (DE) [e-mail] 

(Asia) [e-mail]

ETC Installation Guide

Back box
(not provided)

Mounting
plate

Canopy
screws

Ground
braid

Mounting plate
screws

Canopy plate: the four
indentations allow for
multiple screw nesting
positions.

Ground
screw

Source Four Mini LED

Canopy Installation Procedure

Step 1: Remove the mounting plate from the fixture by removing the two

Step 2: Using the mounting plate screws, secure the mounting plate to the

CAUTION:

canopy screws and the ground screw. Set the ground screw safely
aside.

installed electrical box, which is not included.

The metal canopy plate has built in indentations allowing
the mounting plate screws to nest into the canopy plate.
For an ideal flush mount installation you may need to
rotate the plate to accommodate these indentations. See
the following graphic for additional information.

Canopy and Track Mount Kits Page 2 of 4

ETC Installation Guide

Canopy
screw
hole

3

2

1

3

2

1

Mounting plate screw

installation detail

Canopy
screw
hole

Install the mounting
plate screws in one of
the three position­pairings shown.

Only the slots on the
outer circumference
will allow a true flush
mounting.

Source Four Mini LED

Step 3: Place the copper ground braid loop over the ground screw and attach

the ground screw to the back box.

Step 4: Connect the building ground wire to the ground wire on the fixture,

following local electrical codes.

Step 5: Connect your supply power wires to the lamp wiring using the included

two-position Wagos.

For 120V fixtures: Connect the black wire to line and the white wire to neutral.
For 230V fixtures: Connect the brown wire to line and the blue wire to neutral.

Step 6: While keeping in mind the mounting plate orientation, use the canopy

screws to secure the fixture to the mounting plate.

Step 7: Open all four of the shutter blades by sliding them outward until they

Step 8: Install a gobo and gel as desired and confirm that they are properly

Step 9: Restore power at the main fuse.

Step 10: Focus the fixture as desired.

stop.

secured.

Page 3 of 4 Canopy and Track Mount Kits

ETC Installation Guide

Circuit selection

wheel

Lock

Tabs

There are cable protection posts

on both the yoke lock and the

yoke that prevent the fixture from

rotating a full 360°.

The yoke can be locked into

place using a 1.5mm Allen

wrench.

Source Four Mini LED

Track Installation Procedure

WARNING:

AVERTIR:

Step 1: Insert the track adapter into the

Step 2: Lock the adapter into place.

Step 3: Select circuit 1 or 2 using the

The 230V track adapter has a three­circuit selector knob.

Step 4: Focus the fixture.

Step 5: Lock the fixture into place using the yoke lock.

To reduce the risk of fire and electric shock, use only with
EUTRAC track system.

Réduire le risque de feu et la décharge électrique, l'usage
seulement avec le systéme de piste d'EUTRAC.

track. The adapter will only fit one
way into the track with the tabs of
the adapter in the groove of the
track.

circuit selection wheel.

Canopy and Track Mount Kits Page 4 of 4