ETC Source Four LED Profile Quick Manual
ETC® Quick Guide
Source Four LED™ Profile
Source Four LED Profile v1.3.0 Quick Guide Page 1 of 7 Electronic Theatre Controls, Inc.
Corporate Headquarters
3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA Tel +608 831 4116 Fax +608 836 1736
London, UK
Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK Tel +44 (0)20 8896 1000 Fax +44 (0)20 8896 2000
Rome, IT
Via Pieve Torina, 48, 00156 Rome, Italy Tel +39 (06) 32 111 683 Fax +44 (0) 20 8752 8486
Holzkirchen, DE
Ohmstrasse 3, 83607 Holzkirchen, Germany Tel +49 (80 24) 47 00-0 Fax +49 (80 24) 47 00-3 00
Hong Kong Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong Tel +852 2799 1220 Fax +852 2799 9325
Service:
(Americas) service@etcconnect.com
(UK) service@etceurope.com (DE) techserv-hoki@etcconnect.com
(Asia) service@etcasia.com
Web:
www.etcconnect.com
Copyright © 2012 ETC. All Rights Reserved. Product information and specifications subject to change.
7460M1300-1.3.0 Rev B Released 2012-04 ETC intends this document to be provided in its entirety. US and international patents pending
Overview
For complete information and step-by-step instructions, see Source Four LED Profile v1.3.0 User
Manual.
Accessory
holder
Yoke
Accessory
retainer
Yoke
locking knob
Safety cable
loop
LCD
DMX Thru
DMX In
Keypad
Power In
Power Thru
Status
indicators
Light Bulb
Home
Back
Up
Enter
Down
Power – Indicates AC power is On.
DMX – Indicates control signal is Active.
Error – Indicates data error, high temperature, or other unusual status.
ETC Source Four LED Quick Guide
Install Lens Tube
Source Four LED Profile v1.3.0 Quick Guide Page 2 of 7 Electronic Theatre Controls, Inc.
Install Lens Tube
Step 1: Slide lens tube into shutter barrel.
Step 2: Install the lens zoom knob.
Step 3: Install the Phillips screw in the top of the lens barrel.
Install Fixture
Step 1: Hang or mount the fixture.
Step 2: Attach safety cable.
Step 3: Insert additional accessories such as a top hat, etc.
WARNING:
Use only hardware rated for total weight of fixture and accessories.
A safety cable (or other approved safety device) must be securely attached
to the safety cable loop before loosening the clamp.
Low clearance position
General use position
ETC Source Four LED Quick Guide
Connect
Source Four LED Profile v1.3.0 Quick Guide Page 3 of 7 Electronic Theatre Controls, Inc.
Connect
Step 1: Attach power cable to Power In.
Step 2: Attach 5-pin XLR cable to DMX In (if using external control).
Step 3: Connect power cable to AC power.
Step 4: Plug XLR cable (if using) into data source.
Step 5: Link additional fixtures via Power Thru and DMX Thru connectors.
Focus
Step 1: Supply power and wait for the fixture to boot up.
Step 2: Press [Light Bulb] to open Presets & Sequences.
Step 3: Select Focus and press [Enter] to turn on LED array.
Step 4: Adjust fixture's position.
Step 5: Once focus is set, press [Enter] to turn off LED array and then [Home] to return to home
screen.
WARNING:
No more than nine Source Four LED fixtures per circuit (non-dimming, 100
to 240 VAC, 50/60 Hz)
Up to 32 device loads on the DMX daisy-chain.
Disconnect Power and DMX before all cleaning and maintenance.
Power In
Power Thru
DMX In
DMX Thru
Loading...