Source Four HID PARNel™ CE User Guide
DECLARATION OF CONFORMITY
We, Electronic Theatre Controls, Europe Limited
Unit 5, Victoria Industrial Estate, London W3 6UU United Kingdom declare under sole responsibility that
the product:
Product name: Source Four HID luminaires
Product type/model: 405HID, 410HID, 419HID, 426HID, 436HID, 450HID, 41530 HID, 42550
HID, 426HIDJ, 436HIDJ, 450HIDJ, 2550HIDJ, PAR-EAHID, PARNel HID
Lot: n/a
Batch / Serial number: n/a
Item numbers: one of each type
to which this declaration relates is in conformity with the following Standards:
EN60598-1:2000 Luminaires, General requirements and tests
EN60598-2-17:1990 Luminaires, Particular requirements, Specification for luminares for
stage lighting, television, film and photographic studios (outside and
indoor) - equiv. BS 4533-102.17:1990
BS EN 60922:1997 Auxileries for lamps. Ballasts for discharge lamps (excluding tubular flu-
orescent lamps). General and safety requirements.
Following the provisions of EU LV Directive(s) 73/23/EEC
EN55015:1996 Limits and methods of measurement of radio disturbance characteristics
of electrical ligthing and similar equipment.
EN61000-3-2:2001 Electromagnetic compatibility (EMC) Limits. Limits for harmonic current
emissions (equipmetn input current up to and including 16 A per phase) Class C
EN61000-3-2:1995 Electromagnetic compatibility (EMC) Limits. Limitation of voltage fluctua-
tions and flicker in low voltage supply systems for equipment with rated
current <= 16 A
London, United Kingdom
Adam Bennette
(Place of issue) (Name of authorised person)
13th December 200213th December 2002
(date of issue) (signature of authorized person)
Electronic Theatre Controls Europe Ltd. Registered office:
Unit 5, Victoria Industrial Estate, Grant Thornton House
Victoria Road, London W3 6UU U.K. Melton St., London, NW1 2BW, England
English
Source Four HID PARNel CE guidelines
Please note the following precautions prior to use:
The Source Four HID PARnel CE is intended for professional use only. Read the entire User Guide before
using equipment.
Please note the following safety precautions:
• The Source Four HID PARNel CE is NOT dimmable. Dimming or regulated voltage will damage the ballast and
void the warranty.
• Do not mount the Source Four HID PARNel CE on or near a flammable surface.
• Use the Source Four HID PARNel CE in dry locations only, where humidity does not exceed 90 percent.
• The fixture is for indoor use only and is not intended for outdoor use.
• For temporary installations, mount and support the Source Four HID PARNel CE only by the primary suspension
yoke holes. Suspend the fixture from a hook clamp or a stand mount, using a securely tightened steel bolt (up to Ø
12 mm), flat washer and locking washer.
• In addition to primary suspension, attach a safety cable (Model 400SC) or chain to the secondary suspension
point on the Source Four HID PARNel CE.
• If the external cable is damaged, it shall be replaced by ETC or our service agents.
• Always hang the Source Four HID PARNel CE with the colour frame held securely behind the PAR retaining channel.
• Always replace the lamp if it becomes damaged or thermally deformed.
• Lighted objects at this distance or greater will not exceed 90ºC temperature from projected light.
• Disconnect the unit from power before all cleaning and maintenance.
• The Source Four HID PARNel CE is suitable for indoor use with a maximum ambient temperature: Ta=45°C
• Maximum exterior surface temperature: T
• A multilingual label sheet is included with this manual. Affix the label of the appropriate language over the existing
warning label on the extension yoke. Do not cover ETC trademark or CE mark.
• The Source Four HID PARNel CE contains a CE safety screen that covers the lens in the event of accidental discharge. Do not remove the safety screen.
• Keep the luminaire at least 0.7 meters away from anything it is shining on.
max
=200ºC
0.7m
Source Four HID PARNel CE 3
English
Wiring and power information
A plug of at least 2.5 amp (220/240V) rating should be attached to the fixture’s mains lead. The wires in the mains
lead are 1.5mm2 each and coloured in accordance with the following code:
Green and Yellow:
Blue: Neutral
Brown: Live
Earth
WARNING: The CE Source Four HID PARNel CE must be earthed.
Current rating: 240V/2.5 amp maximum
Operating frequency:
50/60Hz
Accessories
ETC Part #
Colour frame (19 cm sq./17 cm.inside diameter) 7061A3047
Safety cable (79 cm) 7061A1022
C-clamp 7060A2009
Top hat, 7.62 cm PSF1022
Top hat, 15.24 cm PSF1023
Half hat PSF1027
Cross-baffle top hat PSF1031
Egg-crate louver PSF1028
Weighted base PSF1032
Gel Extender 7.62 cm PSF1030
Gel Extender 15.24 cm PSF1029
Barn door PSF1019
t 180°c
HID Lamp type and general information:
Do not use lamps other than the following types in the Source Four HID PARNel CE. Use of lamps other than
specified below will void CE safety compliance and your warranty.
Lamp Type Manufacturing Codes Watts Base Bulb LCL Ave.
CDM-T 150W/830 150 G12 T6 56mm 9000 14000 3000°K
Ceramic
Metal
Halide
CDM-T 150W/942 150 G12 T6 56mm 9000 12700 4000°K
MD150T6/U/G12/
830
MBI150/T/30 150 G12 T7 57mm 6000 11500 3000°K
MBI150/T/40 150 G12 T7 57mm 6000 11250 4000°K
150 G12 T6 56mm 9000 14000 3000°K
Hrs.
Initial
lumens
Color
temp
4 Source Four HID PARNel CE
Installing the lamp
1. Disconnect power to the Source Four HID PARNel CE before installing the lamp.
2. Loosen the knurled bolt on the back of the lamp housing and pull the housing out.
3. Holding it by the base, remove the lamp from its box.
English
Note:
To avoid premature lamp failure, do not touch the lamp glass with your fingers. If you
touch the lamp during installation, clean it carefully with rubbing alcohol and a clean, lintfree cloth before operation.
4. Insert lamp base into socket assembly. (Figure 3)
5. Push down on the lamp base until the lamp seats firmly.
6. Reinstall the lamp housing by aligning the bolt hole and tightening the knurled bolt.
CAUTION:
Replace the lamp if it becomes damaged or thermally deformed.
Improperly installed lamps will cause premature lamp and socket
failures.
Figure 1
Ballast information
• The only acceptable voltage is 120V (+/- 10%) 50/60HZ.
• The standard operating current is 1.5 Amps.
• The standard inrush current is <14 Amps.
• Room ambient temperature should not exceed 40ºC.
• The lamp ignition voltage is 4.5Kv, non-hot restrike.
• The ballast case temperature should not exceed 75ºC.
• The ballast is attached to the Source Four yoke by two screws and is non-removable.
WARNING: DO NOT power the Source Four HID PARNel CE with a dimmable power supply.
Dimming will damage the ballast and void the warranty.
Source Four HID PARNel CE 5
English
n
Color frame retaining clip usage
The color frame holder is equipped with a spring-loaded retaining clip that prevents color frames and accessories
from falling out. Make sure the Source Four HID PARNel has the color frame retaining clip in the locked position
when hanging.
(Figure 2)
Note:
1. Release the retaining clip by pushing it sideways. The retaining clip opens.
2. Insert the color frame.
3. Press the retaining clip down until it locks.
Make sure to use colorframes or accessories with a 17cm inside diameter.
Retaining clip in
the locked positio
Figure 2
Focus Knob Positioning
45º field angle
Focus knob in
flood position
Focus knob in
spot position
To adjust the Focus knob tension, loosen or tighten the Focus knob screw.
CAUTION:
Focus knob screw
25º field angle
Focus knob screw
The focus knob does not rotate 360º. Do not attempt to exceed rotational limit.
Overtightening may result in damage or breakage of the knob.
6 Source Four HID PARNel CE
Lens identification
s
The Source Four HID PARNel CE comes equipped with two types of lenses; Wave/Stippled (WS) and Wave/Clear
(WC). The type can be identified by the lens texture.
The WC rear lens is in a “fixed” position inside the fixture. The WS lens is in the rotating ring at the front of the fixture. The wave surfaces face each other.
English
WS
Wave / Stippled lens
WC
Wave / Clear lens
Changing Source Four PARNel lenses
Change lenses if they become cracked or badly scratched.
CAUTION:
Removing a wave/stippled front lens
1. Source Four HID PARNel CE lenses get hot while the unit is in operation. Let the fixture cool before handling
the lens.
2. Disconnect power from the fixture.
3. Place the fixture on a flat, stable work surface. Do not install or remove lenses with the unit hanging.
4. Rotate the focus knob to full spot position.
5. Tilt the front of the fixture down at least 45 degrees.
6. Press the spring clip with your finger to release the lens (Figure 3).
7. Allow the lens to drop forward from under the clip.
8. When the lens drops, remove your finger, allowing the lens to slide forward until it rests on the lens catchers
(Figure 4).
9. Carefully remove the lens from the fixture.
Never operate the Source Four PARNel without a lens in place.
Retaining clip
Spring clip
Spring clip
WC lens
Focus Knob
Retaining clip
WS len
Tab
Figure 3
Lens catcher
Figure 4
Tab
Figure 5
Installing a wave/stippled lens (front)
1. Position the fixture with the front of the unit (the lens side) facing you, and tilted slightly (Figure 3).
2. Rotate the focus knob to full spot position.
3. Hold the lens by the edge, and position it so the wave side faces the back of the fixture (Figure 5).
4. From the top of the fixture, slide the lens behind the lens catchers and position its base behind the tabs on the
bottom of the lens rotation ring. See Positioning the wave/stippled lens below.
5. Gently push the top of the lens inward until it snaps behind the spring clip.
Source Four HID PARNel CE 7
English
Positioning the wave/stippled lens (front)
• There are seven “notches” cut into the stippled side of the lens. Position the lens so that the cluster of three
notches is on top. The center notch of the cluster coincides with the spring clip on the lens retaining ring.
6)
• The bottom of the lens has a cluster of four notches. Place the two center notches behind the tabs at the bottom
of the lens rotating ring.
(Figure 5)
Top center notch
Bottom two
center notches
Figure 6
Cleaning the reflector
1. Unplug the fixture before attempting to clean the reflector.
2. Remove the lamp before attempting to clean the reflector.
3. Remove the lenses so you can access the reflector from the front of the fixture.
4. Remove dust with a blast of oil free air, or wipe with a clean, soft, lint-free cotton cloth. If this is sufficient to
remove dust, go to step 7. Otherwise, continue to step 5.
5. Dampen a clean, soft, lint-free cotton cloth with a mild, soapy water solution and gently wipe the reflector.
6. Remove any soapy water residue with a clean, soft, lint-free cotton cloth dampened with water.
7. Reinstall the lenses before using the fixture.
(Figure
CAUTION:
Do not use glass or window cleaners on the reflector. Chemicals in the cleaners
will harm the reflective coating. Do not use paper towels or harsh materials to wipe
the reflector. These materials can scratch the surface of the reflector.
Housing assembly instructions
If you take apart the Source Four HID PARNel CE for any reason, please use the following steps for reassembly.
Improper reassembly will result in void of warranty and loss of performance.(See parts list on page 10)
Tools required: Phillips screwdriver.
1. Install the reflector mount silicon pads (11) and lens pad (15) in the left barrel (7 or 8).
2. With the wave side of the lens facing toward the front of the fixture, install the wave/clear lens (21) into the rear
lens track.
3. Assembly items 16, 17, 18, and 19 (Focus knob assembly). Rotate the focus knob full spot position. The arrow
on the focus knob will point approximately to the 11 O’clock position.
4. Place the focus knob assembly into the left barrel.
5. Install the lens stop (14) and the rotator spring clip (12) into the lens rotator (12 or 13).
6. Install the lens rotator into the left barrel.
7. Install the rotator pressure clip (9) into the left barrel with screw (23).
8. Install the gel retainer clip (1) and the spring (22) into the right barrel (5 or 6).
9. Attach the right barrel to the left barrel using screws (3) in three places.
10. Check that the gel clip retainer (1) moves easily into position.
11. Check for smooth rotation of the lens rotator (12 or 13).
12. With the wave side facing inward, install the wave/stippled lens (20) into the lens rotator.
8 Source Four HID PARNel CE
Spare parts list
English
13,14
10 9 12
5,6
3,4
8
7
11
1,2
12 9 10
Source Four HID PARNel CE Final Assembly
Reference
Number
1 7061A2022
2 7061A2022-1
3 7061A2024-0X
4 7061A2024-1X
5 7061A3039
6 7061A3039-1
7 HW5125 Bolt, carriage 1
8 HW5126 Washer, flat 1
9 HW5139 Washer, split ring lock 2
10 HW5172 Bolt, hex 2
11 HW5270 Bolt, spinlock 2
12 HW522 Washer, flat 2
13 HW8144
14 HW8144-1
Part Number Description Quantity
Required
S4 HID PAR base
assembly (black)
S4 HID PAR base
assembly (white)
120V HID PAR Lamp
socket assembly (black)
120V HID PAR Lamp
socket assembly (white)
HID PAR yoke bracket
(black)
HID PAR yoke bracket
(white)
Handle, yoke knob
(black)
Handle, yoke knob
(white)
1
1
1
1
1
1
1
1
Source Four HID PARNel CE 9
English
Spare parts list
9
3
7
8
11
2
21
4
15
1
23
14
17
22
16
12
18
19
20
13
Source Four HID PARNel CE Housing Assembly
Reference
Number
1 7061A3005 Gel retainer clip 1
2 7061A3013 Spring clip rotator 1
3 7061A3014 Reflector, painted black 1
4 7061A3014-1 Reflector, painted white 1
5 7061A3025 Barrel, painted black 1
6 7061A3025-1 Barrel, painted white 1
7 70612019 Source Four PAR rivet assembly, black 1
8 70612019 Source Four PAR rivet assembly, white 1
9 70613029 Rotator pressure clip 1
10 HW492 Screw, 10-32 X 5/8, PhPH Taptite 3
11 7061A4001 Pad, silicon reflector mount 2
12 70614012 Lens rotator, black 1
13 70614012-1 Lens rotator, white 1
14 7061A4029 Lens stop 1
15 7061A4020 PARNel lens pad 4
16 7061A4013 Focus knob bushing 1
17 7061A4014 Focus knob gear 1
18 7061A4015 Focus knob 1
19 HW2154 Screw, PPH, 6-19 X 1/2L, 48-2 Plastite 1
20 7061A4010-2 PAR zoom wave/stippled lens 1
21 7061A4010-1 PAR zoom wave/clear lens 1
22 HW750 Spring, retainer 1
23 HW4145 Screw, 10-32 X 3/8, PhPH Taptite, BO 1
Part Number Description Quantity
5
6
10
Required
10 Source Four HID PARNel CE
English
This page intentionally blank
Source Four HID PARNel CE 11
Americas
3030 Laura Lane, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA Tel: +608 831 4116 +800 688 4116
Fax: +608 836 1736 +800 555 8912
Europe
Unit 4, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK Tel: +44 (0)20 8896 1000 Fax: +44 (0)20 8896 2000
Asia
Room 605-606, Tower III Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong Tel: +852 2799 1220 Fax: +852 2799 9325
W
eb: www.etcconnect.com Email: (US) mail@etcconnect.com (UK) mail@etceurope.com (Asia) mail@etcasia.com
Service: service@etcconnect.com
Toll free: 800 775 4382 Comments about this document: techcomm@etcconnect.com
Copyright © 2003 Electronic Theatre Controls, Inc. All Rights Reserved. Product information and specifications subject to change.
7061M1016
Rev A Released 4/03
Loading...