ETC Desire D60 Vivid Data Sheet

ETC

D60 Model Prefix

Color Mix

V = Vivid 7-color standard wash
L = Lustr+ front light
wash variant

Finish Options

0 = Black (standard)
1 = White
5 = Silver or other
custom color
(Contact factory)

Usage Rating

I = IP20 (interior)

Connector Options

X = bare end
A = Parallel blade, U-ground (Edison)
B = Two-pin and ground (Stage-Pin)
C = Grounded 20A twistlock

Note – all IP20-rated fixtures ship standard with
either a bare-end power lead or on Edison
connector-equipped power lead. Other power
lead options are shown in the “Power Lead
Options” table.

SELD60 V I – 0X

®

Desire® Series

D40 D60D40XT

™

Vivid

™

Lustr+

This datasheet covers D60 luminaires as shown.

See other datasheets for other versions.

D60

™

GENERAL INFORMATION

The Selador® Desire D60 fixture puts the seven-color x7 system into
a high-brightness, 60-emitter, round theatrical washlight. Highly
efficient primary lenses and careful color choices make the D60
fixture ideal for stage, studio and anywhere strong color and high­intensity are requirements. The Selador x7 Color System

™

produces
the widest range of spectrally-balanced saturated and tinted color
choices available. D60’s rugged die-cast enclosure; quiet, fan-cooled
operation; multiple lens options; and advanced user interface make it
ideal for multiple applications.

D60 LED array options

D60 fixtures are based on the x7 Color System that uses seven
different LED colors to achieve true, usable broad-spectrum color.
The D60 luminaire is available with any one of the following x7 color
arrays (not interchangeable) to best suit the intended application:

• D60 Vivid – the x7 Color System array balanced for best
all-around use as a color-changing wash fixture

• D60 Lustr+ – optimized array with six colors plus high­ intensity white LEDs to create an ideal frontlight wash fixture
for full-range color, with an emphasis on lighter colors
and white and natural illumination of skin tones

ORDERING INFORMATION

Selador D60

MODEL DESCRIPTION

SELD60VI D60 Vivid

SELD60LI D60 Lustr+

Note: D60 luminaires ship with a hanging yoke, a Very Narrow secondary lens and

an input lead with connector of choice. See page 2 for connector options.
C-clamps are not included.

1 of 7

ETC

®

D60

Desire Series

SPECIFICATIONS

GENERAL

• 60-LED color mixing wash fixture

• ETL Listed to UL 1573 – the standard for stage and studio
lighting units

• IP20-rated for indoor use

• Power and DMX in/thru connections for easy setup

• User-friendly control interface with multiple modes and
fixture settings

PHYSICAL

• Rugged die-cast all-metal housing

• Easy access slots for secondary lenses and accessories

• Uses 8-7/8”/225mm lenses and accessories

• Available in black (standard), white or silver (optional) or
custom colors (contact factory)

• Hanging yoke standard. Optional yoke/floor stand available

ELECTRICAL

• 100VAC to 240VAC 50/60Hz universal power input

• Neutrik power in and thru connections

• Up to nine fixtures (15A max) may be linked via power thru
connector (10 fixtures total per circuit) when used with R20
Relay Module or Unison Echo Relay Panel. Consult breaker
trip curves when used with other equipment

• Requires power from a non-dim source

• Inrush

- 120V: 15A (First half-cycle)

- 240V: 40A (First half-cycle)

LED*

• 50,000-hour LED life (50,000 hours to 70% intensity)

• 60 Luxeon

*See additional LED notes on page three

COLOR

• Exclusive x7 Color System

• Beautifully illuminates skin tones and other objects for
natural appearance and high color rendering

• Broad spectrum color interacts seamlessly with
conventional sources

• Exclusive red-shift option emulates tungsten
dimming performance

• Variable color temperature from 2700K-6500K

OPTICAL

• Primary field angle of 17

• Secondary lenses available for multiple beam-spread options

• Each fixture ships with a Verry Narrow lens; additional lenses
must be ordered separately

• Refer to accessory charts for lenses available

CONTROL

• DMX512 in and thru via five-pin XLR connectors

• Multiple control options including RGB, strobe, and console­ free Master/Slave mode

• See DMX Control Table for additional information

• 15-bit virtual dimming engine provides smooth, high-quality
theatrical fades and minimizes color-shift during dimming

• RDM functionality for address and setting changes

THERMAL

• Ambient operating temperature of -4

• Active electronic thermal management for
droop-free operation

• Low-noise fan cooling

• Fixture is designed for continuous operation up to

104
air around fixture housing

®

Rebel LED emitters

™

seven-color LED arrays

°

and beam angle of 8

°

to 104°F (-20° to 40°C)

°

F (40°C) ambient temperature and requires free flow of

°

ADDITIONAL ORDERING INFORMATION

Power Input Cables

Use information below to order 5’ power input leads with factory-fitted connectors

MODEL DESCRIPTION

DPA-A 5’ PowerCon

™

to parallel blade U-ground

(Edison) connector

DPA-B 5’ PowerCon to 20A two-pin and ground (stage pin)

connector

DPA-C 5’ PowerCon to grounded 20A twistlock connector

DPA-X 5’ PowerCon to bare-end power input lead

Power Thru Jumpers

Note: Power thru jumpers connect to fixture’s output (thru) connector to provide

link
to successive fixtures

MODEL DESCRIPTION

DPJ-5 5’ PowerCon to PowerCon

fixture to

fixture jumper

DPJ-10 10’ PowerCon to PowerCon

fixture to

fixture jumper

Fixture Accessories

MODEL DESCRIPTION

SELD60FSY D60 floor stand yoke combo

490BD Barn door (Use only as a flexible top hat to diminish

aperture glare. Not for beam shaping)

490CF Color Frame (use for round and oblong lenses)

490L Egg Crate Louver

490PTH3 Top Hat 3” Tube

490PTH6 Top Hat 6” Tube

490PHH Half Hat 6” Tube

400CC C-Clamp (does not ship with fixture)

400SC Safety Cable (32”)

DPSJ-25 25’ PowerCon-to-Edison

inline switch

2 of 7

input power cable with

ETC

®

D60

Desire Series

ADDITIONAL ORDERING INFORMATION

Secondary Lens Options

MODEL DESCRIPTION: The following lenses are cut for

D60 fixtures and create round, linear or oblong
field patterns as described below. These lenses are
not sized for use in Selador

Narrow
Linear Field

SELLVN-9 9” Very Narrow lens

SELLN-9 9” Narrow lens

SELLM-9 9” Medium lens

SELLW-9 9” Wide lens

SELLEW-9 9” Extra Wide lens

Round Field

SELRVN-9 9” Very Narrow lens (round field)

SELRN-9 9” Narrow lens (round field)

SELRM-9 9” Medium lens (round field)

SELRW-9 9” Wide lens (round field)

Oblong Field

SELON-9 9” Narrow lens (oblong field)

SELOM-9 9” Medium lens (oblong field)

SELOW-9 9” Wide lens (oblong field)

Note: This is the same material as Selador
Classic lenses

®

Classic fixtures.

Linear lenses
may be
combined
to create
desired field
size

Desire lenses compared to Source Four PAR EA

NOTES ABOUT LED LUMINAIRES

All LED sources experience some lessening of light output and some
color shift over time. LED output will vary with thermal conditions.
Based on the LED manufacturer’s B50 L70 specification, a Selador
luminaire will achieve ~70% of its initial output after 50,000 hours of
typical usage. In individual situations, LEDs will be used for different
durations and at different levels. This can eventually lead to minor
alterations in color performance, necessitating slight adjustments to
presets, cues or programs.

CRI AND CQS RATINGS

Desire fixtures were evaluated for CRI and CQS performance using
measured output spectrum and optimized mix solutions for a best
spectral match to black body sources at 3200K and 5600K.

Fixture CRI CQS Color

D60 Vivid at 3200K 87 89 89 0.000

D60 Vivid at 5600K 90 92 92 0.000

D60 Lustr+ at 3200K 86 88 88 0.000

D60 Lustr+ at 5600K 93 92 92 0.000

D60 Studio HD at 3200K 89 90 91 0.000

D60 Studio HD at 5600K 92 94 94 0.000

D60 Studio Daylight
5600K

D60 Studio Tungsten at
3000K

at

71 70 63 0.001

86 86 86 0.001

Fidelity

Duv

Typical Lens Field Profiles

Narrow Linear

Round

Oblong

Power Consumption at Full Intensity

VOLTAGE

MODEL

SelD60 120 / 240 1.35/0.68 161

(V)

CURRENT

(A)

WATTS

All D60 luminaire versions provide excellent color rendering to the
eye, particularly at higher color temperature settings, such as 5600K.
In most cases the Duv is 0.000. A Duv rating of 0.000 indicates that
the color mix used is exactly on the black body line, with no green or
magenta tint.

3 of 7

ETC

®

D60

Desire Series

LENS INFORMATION

Desire diffusion angle measurements

NOMINAL

No Lens

D60

LUSTR+ 18 22 27 42 69 104 20 x 37 25 x 60 30 x 82

VIVID 18 22 27 42 69 104 20 x 37 25 x 60 30 x 82

STUDIO HD 18 23 28 42 69 104 21 x 29 25 x 61 30 x 82

STUDIO D 22 25 30 43 70 105 24 x 39 28 x 62 32 x 80

STUDIO T 23 25 30 43 70 105 24 x 39 28 x 62 32 x 80

Values in black refer to old lens descriptions.

Very

Narrow

25° 35° 45° 75° N/A 20° x 40° 30° x 70° 35° x 80°

Narrow Medium Wide Extra Wide

Narrow

Oval

Medium

Oval

Wide Oval

4 of 7

ETC

®

D60

Desire Series

CONTROL OPTIONS

User settings on D60 fixtures allow multiple operational modes and
settings for either console operation via DMX protocol or stand-alone
operation. The expanded LCD display provides easy navigation to all
possible settings and options. Some of the setting options are:

• Multiple DMX choices ranging from a simple RGB

profile – which effectively controls all seven LED colors via
three channels – to nine-channel ‘direct’ color and
intensity control

• Multiple dimming curve options

• Preset colors and effects for stand-alone (no console

required) operation

• White point selection – white light and color behavior based

on a specific color temperature white light, i.e. 3200K,
5600K, etc.

• Loss of data behavior options – instant off, hold last look for

two minutes, etc.

• Output modes – three output options that offer the user a

choice between maximum output and maximum consistency
See the User Manual for a complete explanation of all of the control
settings and options for the D60.

Quick Setups

To assist in managing the numerous control and fixture behavior
choices, five combinations of operational settings are available
to quickly get started. These settings are specifically created for
different situations and are easily accessible at the fixture display.
Each setting can then be modified as required to take advantage of
all of the possible control features.

Setting

Title

General Direct Factory Default:

Stage HSI

XT Arch HSI Exterior architectural lighting:

High
Impact

Studio Studio Studio Factory Default:

*See user manual for complete list of features for each Quick Setup

Profile Description Typical Features*

For general-purpose
use, including interior
architectural applications

Plus 7
Enabled

RGB Event lighting:

Theatrical lighting:
Duplicates the color and
dimming behavior of
tungsten stage lighting
fixtures

Provides a high degree of
color consistency in high
ambient temperature
envionments

Enables quickest response,
simple RGB control and
strobe channel for maximum
effect usage

Enables three-parameter
control of white light
(intensity, white point, and
tint) via DMX from a console
or console-free fixture display

• Standard dimming curve

• Regulated output for
color consistency

• Incandescent dimming
curve

• Regulated output for
color consistency

• 3200K white point
setting

• Standard dimming curve

• Protected output

• 3200 white point setting

• Quick dimming curve

• Boost mode for
maximum intensity

• 5600K white point
setting

• Linear dimming curve

• Regulated output mode
for color consistency

CONTROL OPTIONS

DMX Input Channel Profiles

DMX

Profile

Direct 10 1 – Red

HSI 6 1 – Hue (coarse)

HSIC 7 1 – Hue (coarse)

RGB 6

Studio 6

Additional profile options

Plus 7 Seven additional color-control channels are available in

Strobe Variable strobe control: 0% is no strobe. The fixture

5 of 7

DMX

Channels

(Ch. 4

not used)

(Ch. 4

not used)

Channel

Assignments

Direct control of each individual
2 – Orange
(white if Lustr+)
3 – Amber
4 – Green
5 – Cyan
6 – Blue
7 – Indigo
8 – Intensity
9 – Strobe
10 – Fan Control

2 – Hue (fine)
3 – Saturation
4 – Intensity
5 – Strobe
6 – Fan Control

2 – Hue (fine)
3 – Saturation
4 – Intensity
5 – Strobe
6 – Fan Control
7 – Color Point
(CCT)

1 – Red
2 – Green
3 – Blue
4 – n/a
5 – Strobe
6 – Fan Control

1 – Intensity
2 – Color Point
(CCT)
3 – Tint
4 – n/a
5 – Strobe
6 – Fan Control

RGB, HSI, and HSIC input profile settings. For example,
HSI with ‘Plus 7’ enabled becomes a 15-channel profile:

1 – Hue (coarse)
2 – Hue (fine)
3 – Saturation
4 – Intensity
5 – Strobe
6 – Fan Control
7 – n/a
8 – Plus7
Control on/off
9 – Red
10 – Orange
(white if Lustr+)
11 – Amber
12 – Green
13 – Cyan
14 – Blue
15 – Indigo

output will strobe more rapidly as the strobe-channel
value approaches 100%.

color with a separate master

intensity channel. Color calibration

of LEDs is not active in this mode.

The ten-channel profile will

produce the highest-quality color

crossfades.

High-resolution hue (two

channels), saturation, and intensity

control. HSI mode will produce

color crossfades around the color

space.

High-resolution hue, saturation

and intensity control as above,

with the addition of a color-

point channel to adjust the color

temperature of the fixture in

both white light and color. Color

crossfade performance is the same

as HSI.

Effectively addresses all seven

colors via three channels of

control. RGB profile will produce

medium-quality color crossfades

Controls fixture as a white light

unit. If no DMX, (console input,

for example) is present, fixture

can be adjusted for these three

parameters on the U/I at the back

of the unit.

The desired color and intensity

are achieved by using the HSI or

RGB channels

Placing channel seven at a value

over 51% gives the fixture a

15-channel profile.

Channels 9-15 represent the

native colors of the fixture and

allow the operator to adjust

individual color channels to fine-

tune the color output.

Notes

ETC

Beam Angle

Field Angle

Beam Angle

Field Angle

®

PHOTOMETRICS

D60 Vivid

D60

Desire Series

Cosine Candela Plot

Mode Degree Candela Field

Lumens

Boost - cold

Regulated

17˚

17

170,540 3,760 1,667 28.8

132,451 3,050 1,305 28.3

˚

Beam

Lumens

Lumens

Per Watt

Metric conversions: For meters, multiply feet by 0.3048

For lux, multiply footcandles by 10.76

8˚ 17˚

Throw Distance (d) 10’

3m

Field Diameter 3.0’

0.9m

15’

4.6m

4.4

1.4m

20’

6.1m

5.9’

1.8m

25’

7.6m

7.4’

2.3m

402.1’

122.6m

–

Illuminance (fc) 1,617 719 404 259 1

Illuminance (lux) 17,405 7,736 4,351 2,785 10.76

To determine center beam illumination in footcandles at any throw distance, divide
candela by the throw distance squared

For field diameter at any distance, multiply distance by 0.295
For beam diameter at any distance, multiply by 0.145

140000

120000

100000

80000

60000

Candela

40000

20000

0

-15-10 -5 0510 15

Degrees

Iso-Illuminance Diagram

(Flat Surface Distribution)

Y

X

0.067 0.133

X

Y

10%

50%

% illuminance

footcandle

or lux

D60 Lustr+

Mode Degree Candela Field

Boost - cold

Regulated

™

16˚

16

Lumens

Lumens

195,012 4,317 1,931 33.3

180,097 3,850 1,748 32.7

˚

Beam

Lumens

Per Watt

Metric conversions: For meters, multiply feet by 0.3048

For lux, multiply footcandles by 10.76

6˚ 16˚

Throw Distance (d) 10’

3m

Field Diameter 2.9’

.9m

15’

4.6m

4.3’

1.3m

20’

6.1m

5.8’

1.8m

25’

7.6m

7.2’

2.2m

427.6’

130.3m

–

Illuminance (fc) 1,828 812 457 292 1

Illuminance (lux) 19,676 8,745 4,919 3,148 10.76

To determine center beam illumination in footcandles at any throw distance, divide
candela by the throw distance squared

For field diameter at any distance, multiply distance by 0.288
For beam diameter at any distance, multiply by 0.112

Cosine Candela Plot

200000

180000

160000

140000

120000

100000

80000

Candela

60000

40000

20000

0

-15-10 -5 0510 15

Degrees

Iso-Illuminance Diagram

(Flat Surface Distribution)

Y

X

0.067 0.133

X

Y

10%

50%

% illuminance

footcandle

or lux

6 of 7

ETC

SIDE VIEW

REAR VIEW

®

D60 ACOUSTICAL INFORMATION

FIXTURE SPEED SOUND PRESSURE LEVEL*

Background noise level in test chamber N/A 18.3 dBA

Selador Classic Single fan speed 28.1 dBA

Desire D60 30% 25.0 dBA

51% 37.4 dBA

60% 38.6 dBA

100% 43.1 dBA

* Average of readings from four sides of fixture

The fan in all D60 fixtures is thermostatically controlled to run
as needed.

• In regulated mode, fan speed in color-mixing fixtures (Vivid,
Lustr+, etc.) will typically not rise above 30% when at full
intensity in normal room temperature.

• 60% fan speed may be noted in Studio Daylight and Studio
Tungsten fixtures at high intensities at room temperature.

D60

™

Desire™ Series

PHYSICAL

Selador D60 weights and dimensions

WEIGHT* SHIPPING WEIGHT

lbs kgs lbs kgs

19.1 8.7 21.5 9.7

* Does not include mounting hardware

7.0”

178mm

9.8”

249mm

4.5”

114mm

6.6”

168mm

11.4”

290mm

13.9”

353mm

14.2”

361mm

9.7”

246mm

10.6”

270mm

12.2”

309mm

FRONT VIEW

Corporate Headquarters • 3031 Pleasant View Rd, PO Box 620979, Middleton WI 53562 0979 USA • Tel [phone] • Fax [phone]
London, UK • Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK • Tel [phone] • Fax [phone]
Rome, IT • Via Pieve Torina, 48, 00156 Rome, Italy •Tel [phone] • Fax [phone]
Holzkirchen, DE • Ohmstrasse 3, 83607 Holzkirchen, Germany • Tel [phone] • Fax [phone]
Hong Kong • Room 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong • Tel [phone] • Fax [phone]
Web • www.etcconnect.com • Copyright©2015 ETC. All Rights Reserved. All product information and specifications subject to change. 7410L1006 Rev. 0 USA 09/15

This product is protected by one or more of the following U.S. Patents: 6,016,038, 6,150,774, 6,788,011, 6,806,659, 6,683,423 and 7,023,543

7 of 7