ETC DEBC-1 Data Sheet

ETC
®
DMX Emergency Bypass Controller
Emergency Series
GENERAL INFORMATION
The DMX Emergency Bypass Controller provides a simple and cost-effective solution for control bypass of LED houselight systems in emergency lighting applications. The DMX Emergency Bypass Controller uses a single contact-closure input to bypass the DMX control signal and drive all connected loads to full. Optionally, selected fixtures can be controlled using the snapshot setting.
APPLICATIONS
• DMX houselights
• Permanently-installed, DMX-controlled LEDs
• Theaters
• Auditoriums
• Houses of worship
FEATURES
• DMX control bypass
• Wires in-line with DMX to fixtures or other devices
• Uses a single maintained contact closure to activate DMX bypass
• Drives all 512 channels to full when contact closure is present
GENERAL
• UL924 Listed
• RoHS compliant
• WEEE compliant
• 1-output or 6-output models (single universe input)
ORDERING INFORMATION
DMX Bypass Kit
MODEL DESCRIPTION
DEBC-1 DMX Emergency Bypass Controller, 1-output
DEBC-6 DMX Emergency Bypass Controller, 6-output
Related Products
MODEL DESCRIPTION
EBDK Emergency Bypass Detection Kit
SC1008 Branch Circuit ELTS (BCELTS)
ELTS2 Emergency Lighting Transfer System
Note: the DMX emergency bypass controller is suitable for use with UL924 listed fixtures and power panels as part of a control bypass system for emergency lighting. Appropriate UL1008 listed power transfer equipment is required to comprise a complete emergency lighting system.
1 of 4
ETC
®
DMX Emergency Bypass Controller
Emergency Series
SPECIFICATIONS
FUNCTIONAL
• Overrides a single universe of ANSI E1.11–2008, USITT DMX512-A control signals from “Normal” to “Bypass” when a trigger signal is detected via a two-pin trigger input
• Sends DMX signal to a single line or up to six (6) optically isolated lines
• Polls the bypass trigger input after a power loss and reacts upon startup
• Does not process DMX input in Normal mode (pass-through)
• Records a single DMX preset (snapshot) of 512 channels for recall during “Bypass” mode
• Recalls default or recorded sequence immediately on restart if the trigger is also applied at restart
MECHANICAL
• Enclosure constructed of 18-gauge, formed steel panels with a removable front cover finished in gray, fine-textured powder-coat paint
• Designed for wall-mount applications
• Internal voltage barrier provides separate wiring compartments for power and control wiring
• LED indicator visible from the exterior of the enclosure.
- Green: power is present and Controller is functioning in normal state
- Red: Controller is functioning in bypass state
• Test button accessible from the front of the enclosure without removing any panels
• The test button is recessed to prevent accidental triggering
• Internally-accessible, labeled DIP switches for configuration of:
- DMX Record mode
- Contact input type
- Wait-time to Restore incoming DMX (bypass trigger removed)
• Internally accessible button for DMX Record (snapshot) with an indicator LED for record action
ELECTRICAL
• Supports 100V to 277V input power, 50/60Hz, 0.2A maximum current
• Power Input terminals accept two 24–10 AWG solid or stranded wires
• Grounding Lug accepts 14-2 AWG solid or stranded ground wire
• Bypass Contact Input supports two 30-12 AWG low-voltage wires with two modes:
- +12VDC sent from the DEBC through a remote contact (dry)
- +12VDC to +24VDC sent from the remote device to the DEBC contact (wet)
• Bypass input configurable as Maintained Normally Open (default) or Maintained Normally Closed
• DEBC-6 model requires normal/emergency power feed
• Supports one universe (512 channels) of Digital Multiplexing (DMX) in accordance with ANSI E1.11–2008, USITT DMX512-A
- DMX Output and DMX Input terminals for Belden 9729 cable or equivalent
- Socketed DMX transceiver chip with onboard spare
• Non-volatile memory for storage of a single recorded scene of 512 channels
• UL and cUL 924 Listed for emergency lighting applications
• DEBC-1 passes RDM data in normal mode
• DEBC-6 passes RDM data through a single passthru output in normal mode
THERMAL
• Ambient room temperature: 0-40°C / 32-104°F
• Ambient humidity: 10-90% non-condensing
2 of 4
ETC
DMX EMERGENCY BYPASS CONTROLLER RISER DIAGRAMS
®
DMX Emergency Bypass Controller
1-OUPUT DMX EMERGENCY
Emergency Series
6-OUPUT DMX EMERGENCY
3 of 4
ETC
space for up to 1”
®
PHYSICAL
DMX Emergency Bypass Controller
Emergency Series
DMX Emergency Bypass Controller Dimensions
*
MODEL HEIGHT WIDTH DEPTH
inches mm inches mm inches mm
DEBC-1, -6 9.0 229 11.0 279 2.0 52
Top View
Front View
(Cover Panel Removed)
11.0” 279mm
DMX+
DMX-
COM
COM
DMX+
DMX-
C7
C9
C5
C13
C18
C17
J5
J1
DMX OUT
DMX IN
CR1
SPARE C2
R3
Q1
Q2
R5
U7
XU7
CR2
CR3
U2
K1
K2
XU2
C25
R21
C26
R10
R6
R2
C4
R15
TP1
TP4
GNDISO
+5VISO
C8
U1
U3
U8
R4
R11
R9
C3
R7
J4
BKGD
U4
C6
C27
R13
R14
R17
C16
TP2 GND
R12
CONFIG
R20
C19C20
S2
STATUS
LD2
U5
RESET
S3
1234
NORMAL/PANIC
TP3
TP5
R1
+5V
LD1
S4
TESTPOINT
R8
RECORD
C10
C14
J3
+
TEST
C22
C24
CDI
L1
U6
VR1
C21
S1
R16
R18
C23
CR4
R19
CR5
J2
PANIC IN
C11
C12
C15
C1
VOUT IN COM
JP2
7180B4641 REV.A
2011 ETC, INC. MADE IN THE U.S.A. ASSEMBLY I.D. LABEL
CONFIG SWITCHES
SWITCH 1 - MODE SWITCH 2 - PANIC INPUT
OFF = ALL FULL MODE ON = RECORD MODE
C28
SWITCH 3SWITCH 4
OFF OFF ON ON ON
R25
VR2
C31
R23
R22
C32
+
R24
C29
CR6
C30
TP6
+12V
AC INPUT
F1
J6
0.5A
TH1
L2
OFF = NORMALLY OPEN ON = NORMALLY CLOSED
PANIC EXIT DELAY
OFF
0 SECONDS
C40
ON
10 SECONDS
OFF
30 SECONDS 10 MINUTES
R29
C33
CR8
U9
L3
+
R27
C36
VR3
C35
C38
T1
C34
C37
CR11
R26
R28
CR9
CR7
CR10
C39
N
L
C41
C42
C43
9.0” 229mm
Side View
2.0” 52mm
0.875 1/2” KO
DMX Emergency Bypass Controller Weight
*
MODEL WEIGHT SHIPPING WEIGHT
lbs kgs lbs kgs
DEBC-1 8 3.6 8.7 3.9
DEBC-6 14.5 6.6 15.2 6.9
Corporate Headquarters n 3031 Pleasant View Rd, PO Box 620979, Middleton WI 53562 0979 USA n +1 608 831 4116 London, UK n Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK n +44 (0) 20 8896 1000 Rome, IT n Via Pieve Torina, 48, 00156 Rome, Italy n +39 (06) 32 111 683 Holzkirchen, DE n Ohmstrasse 3, 83607 Holzkirchen, Germany n +49 (80 24) 47 00-0
Hong Kong n Room 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong n +852 2799 1220 Web n etcconnect.com n Copyright©2016 ETC. All Rights Reserved. All product information and specifications subject to change. 7180L1040 Rev E 10/16
4 of 4
Loading...