ETA Systems PD11LV Owner's Manual

PD11LV

OWNER’S MANUAL

CONDITIONED POWER DISTRIBUTION

MODEL PD11LV – 15 AMPS

2

3

1

2

5

4

6

PD11LV

REAR PANEL

7

8

1 Light Switch - activates rack illumination. Choose HI or LOW intensity
2 Light Tubes - illuminates up to 25 rack spaces or over 3 feet
3 Digital Voltmeter Readout - displays incoming line voltage
4 Circuit Breaker—resetable 15 amp thermal circuit breaker
5 Outlet Switch - lighted power switch activates protection and filtration to all black outlets and front panel outlets
6 Front Panel Outlet - convenient, filtered, protected and switched outlet
7 Power Cord - Six foot heavy duty U-grounded 14-gauge power cord
8 Ivory Outlets - unswitched outlets with continuous power available. Circuit breaker protected.
9 Black Outlets - EMI/RFI filtered, spike/surge protected and switched outlets

PD11LV Operating Instructions:

1. Install in a standard 19” rack or free standing position.

2. Connect Power Distribution power cord (#7) into standard 120V wall outlet.

3. Plug sensitive electrical equipment into conditioned black outlets (#9) or (# 6).

4. Move power outlet switch (#5) to “ON” position to provide power and protection to electrical equipment.

5. For illumination, pull out light tubes (#2) and move light switch (#1) to “HI” or “LOW” position.
IMPORTANT: Be sure light switch (#1) is in “OFF” position when light tubes are recessed.

6. Digital voltmeter readout (#3) is calibrated to nominal 117V at the factory. No adjustment necessary.
When calibration is required for special applications, an adjustable trimpot is located on the voltmeter readout assembly.
WARNING: Removing top cover is necessary. Adjustment must be done by a qualified individual.

7. Digital voltmeter readout (#3) automatically displays incoming voltage when power cord (#7) is connected. If you wish to
have digital display on only when power switch is “ON”, move switch on voltmeter display assembly inside unit to “OFF”
position. WARNING: Removing top cover is necessary. Adjustment must be done by a qualified individual.

9

PD11LV SPECIFICATIONS:

Dimensions 19" L x 7 1/2" D x 1 3/4" H
Weight 7 lbs. (less packaging)
Housing Quality
Electrical 120V, 50/60 Hz, single phase
Max. amps 15/unit
Max. watts 1800/unit
Spike/surge protection Line to neutral, neutral to ground,

Response time < 1 nanosecond
Max. clamping voltage 330V
Max. spike current 6500 amps
Max. surge energy 630 joules total
Noise filter (EMI/RFI) Frequency 150 kHz -200 MHz

Certification ETL Listed

Black powder coated chassis

line to ground

Attenuation up to 20 dB

PD11LV FEATURES

• 10 protected U-grounded power outlets,
8 switched, 2 "always on"

• Four dual 15 amp U-grounded outlets

• One "always on" dual 15 amp U-grounded outlet on back
panel

• Full 15 amps, 1800 watts capacity per unit

• Protected "always on" 15 amp AC power outlet on the
front panel

• Total unit 15 amp circuit breakers located on front panel

• Digital voltmeter readout

• Dual swivel rack high output illuminators with High/Low
settings and easy-to-change bulb accessibility

• Spike and surge protection

• EMI/RFI filtration

• 1 rack space

• 3 year limited warranty

EASY 4-STEP BULB REPLACEMENT 120 volt 4 watt bulb (Christmas tree bulb)

1. Twist cap clockwise

2. Release bulb & socket

3. Replace bulb

4. Replace socket, turn cap counter-clockwise

Power Conditioning Firsts from ETA

• “Always-On” Protected Outlets

• 10 Rear Panel Outlets

• Front Panel Convenience Outlets

• Digital Voltmeter Display Readouts

• Microprocessor Managed Voltage Regulators

• Programmable and Linkable Sequential Turn-on Models

• Models Adaptable for Multiple AC Adapters

• High Amp Conditioned Models

• Easy Bulb Change Feature

Typical Uses

All Professional Permanent Installations,
Recording Studios, Theatres, Schools,
Clubs, Churches, any entertainment
venue, business board rooms, and au­dio/visual multi-use presentation rooms.

Portable Applications

cert Tours, Bands, and D.J. services.

Other Important Applications:

computer networks, and home entertain­ment centers.

Thank you for choosing

ETA Systems Power Distribution

Drawing upon our 20 years of solving
high-amperage lighting needs and lis­tening to customers’ concerns, we
have developed a most extensive line
of Audio Conditioned Power Distribu­tion. As the problems inherent with AC
power increase, you will find ETA pro­viding solutions.

Call 1-800-321-6699 for a Full Line
Brochure

: On-The-Road Con-

A/V racks,

Standard on Every ETA
Power Conditioning Model

• Spike and Surge Protection and EMI/RFI Filtration on All
Three Legs of the Incoming AC Power—A Must to Ensure
Protection of Electronic Components and Equipment.

TM

©

SYSTEMS

A Creative Light & Sound Company

1532 Enterprise Parkway, Twinsburg, OH 44087 USA
330-425-3388 • 800-321-6699 • Fax: [phone]
http://www.etasys.com E-mail [e-mail]

All designs and specifications are subject to change without notice.
Copyright © 2000 ETA Systems. 11/00 6MAN-005