Estate TUD8700WD, TUD8700WS, TUD8700W User Manual
Installation instructions
Undercounter _hwasher
(Plastic Giant Tub IVIodels)
instructions d'installation
Lave-vaisselle encastre
(rnodeles a tres grande cuve en plastique}
Table of Contents ............................................................................. 2
Table des matieres ......................................................................... 17
8575348
Table of Contents
Dishwasher Safety ................................. 2
Installation Requirements ........................... 3
Tools and parts ................................. 3
Location Requirements .......................... 3
Drain Requirements ............................. 5
Water Supply Requirements ...................... 5
Electrical Requirements .......................... 5
installation Instructions ............................. 6
Prepare cabinet opening
using existing utility hookups ..................... 6
Prepare cabinet opening
where there are no existing utility hookups .......... 7
Prepare dishwasher ............................. 9
Make electrical connection ....................... 11
Connect to water supply ........................ 12
Connect to drain ............................... 13
Secure dishwasher in cabinet opening ............. 13
Dishwasher Safety
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
You need to:
oSlowly open dishwasher door while someone grasps the
rear of the dishwasher. Remove shipping materials, drain
hose and lower rack. Close dishwasher door until latched.
Observe all governing codes and ordinances.
®Install this dishwasher as specified in these instructions.
Installation should be performed by a qualified service
technician.The dishwasher must be installed to meet all
electrical and plumbing national and local codes and
ordinances.
Installation Requirements
Tools and Parts
Gather the required tools and parts before starting
installation.
All installations
Tools needed:
+ pliers
+ Phillips screwdriver
o 5/16" and 1/4" nut drivers
or hex sockets
®measuring tape or ruler
e 10" adjustable wrench that
opens to 1-1/8" (2.9 cm)
+ flat-blade screwdriver
®utility knife
e 2 twist-on wire connectors
which are the proper size
to connect your household
wiring to 16-gauge wiring
in dishwasher
flashlight
+shallow pan
+5/8" open-end wrench
®bath towel
+wood block
Parts needed:
* 90° elbow with 3/8" N.RT.
external threads on one
end. (The other end must
fit your water supply line.)
*Teflon _ tape or pipe joint
compound
shims (if instatled with
built-up floor)
small level
in addition, for new installations
Tools needed: Parts needed:
electric drill with 1/2", 3/4"
and 1-1/2" hole saw bits
e small tubing cutter
®wire stripper
e 1-1/2"-2" screw-type clamp
if connecting to waste-tee
, copper tubing (3/8"
recommended) or flexible
stainless steel braided fill
line
. clamp connector or
conduit connector to fit a
7/8" (2.2 cm) diameter hole
Parts supplied
A. 2 - drain hose clamps, 1 large and 1 small
B. 2 - # 10 x 1/2" Phillips-head screws
C. drain hose
B
Make sure all these parts are included.
See separate parts list for accessories available for your
dishwasher.
Location Requirements
Do not run drain lines, water lines or electrical wiring
where they can interfere with or contact dishwasher motor
or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor
should not touch the floor.
Do not install dishwasher over carpeted flooring.
Protect dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by
the warranty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part No. 4396277) is available
from your dealer for installing underneath the countertop,
but is not required.
Check location where dishwasher will be installed.The
location must provide:
oeasy access to water, electricity and drain.
convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum clearance
between the side of the dishwasher door and the wall or
cabinet.
" square opening for proper operation and appearance.
. cabinet front perpendicular to floor.
. level floor. (If floor at front of opening is not level with
floor at rear of opening, shims may be needed to level
dishwasher.)
NOTE:To prevent shifting during dishwasher operation,
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it
winterized by authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the "Cutout dimensions" section.
HelpfulTip: If the floor in the dishwasher opening is
uneven (example: tile flooring only partway into
opening) you will need to take special care in
measuring dimensions and in leveling dishwasher.
_YTeflon is a registered trademark of E.I. Du Pont de Nemours and
Company.
3
Product dimensions
3/4" (1.9 crn)_ _ 25-1/4" (64.1 crn)_
insulation - / / I I
maybe |_24-1/2"(62.2cm)_,,{ [
compressed | | I I
(not used on all I _ _,,__-J_-
models) T
I[[I 33-7/8"
I II I (86cm)m_n.
I III [ withremovedWh_els
_-- 21" (53.3 cm) -_
SIDE VIEW
REAR ViEW
Cutout dimensions
2-1/2"
(6.4 cm)S
\
. 24" (61 cm) _
f All surfaces must be free
from intrusions
34"
(86.4 cm)
rnin. *
9" 2"
(5.1 cm) 10"
1-3/4" 4-1/4' (25.4 cm)
(4.4 cm)S (10.8 cm)S clear areas
Cut holes in shaded area of cabinet walls or floor as specified below:
water line- 1/2" (1.3 cm)
drain line- 1-1/2" (3.8 cm)
direct wire - 3/4" (1.9 cm)
power supply cord- 1-1/2" (3.8 cm)
Measured from the lowest point on the underside of countertop. May be
reduced to 33-7/8" (86 cm) by removing wheels from dishwasher.
_ Minimum, measured from narrowest point of opening.
*_ May be increased to 6-7/8" (17.5 cm) if height of opening is 34-1/2" (87.6 cm)
at its lowest point.
S Both sides
24 '1
cm)
min.
Drain Requirements
. Use the new drain hose supplied with your dishwasher.
If this is not long enough, use a new drain hose with a
maximum length of 12 feet (3.7 m) that meets all
current AHAM/IAPMO test standards, is resistant to
heat and detergent, and fits the 1" (2.5 cm) drain
connector of the dishwasher.
o Connect drain hose to waste tee or disposer inlet
above drain trap in house plumbing and 20" (50.8 cm)
minimum above the floor. It is recommended that the
drain hose either be looped up and securely fastened
to the underside of the counter, or be connected to an
air gap.
c_ _ air gap
o Use an air gap if the drain hose is connected to house
plumbing lower than 20" (50.8 cm) above subfloor or
floor.
o Use 1/2" minimum I.D. drain line fittings.
Water Supply Requirements
_A hot water line with 20-120 psi (138-862 kPa) water
pressure.
o 120OF (49oC) water at dishwasher.
o 3/8" O.D. copper tubing with compression fitting or
flexible stainless steel braided fill line (1/2" minimum
plastic tubing is not recommended).
_A 90 ° elbow with 3/8" N.RT. external pipe threads on
one end.
Do not solder within 6" (15.2 cm) from water inlet valve.
Electrical Requirements
Contact a qualified electrician.
Assure that the electrical installation is adequate and in
conformance with all national and local codes and
ordinances.
You must have:
+ 120-volt, 60 Hz, AC-only, 15 or 20 amp., fused electrical
supply.
+ Copper wire only.
We recommend:
®A time-delay fuse or circuit breaker.
eA separate circuit.
If direct wiring dishwasher:
o Use flexible, armored or non-metallic sheathed, copper
wire with grounding wire that meets the wiring
requirements for your home and local codes and
ordinances.
o Use strain relief method provided with house wiring
junction box or install a U.L.-listed/CSA-certified clamp
connector to the house wiring junction box. If using
conduit, use a U.L.-listed/CSA-certified conduit connector.
If connecting dishwasher with a power supply cord:
" Use Power Supply Cord Kit (Part No. 4317824) marked for
use with dishwashers. Kit contents include:
-Volex, Inc., UL listed 16 gauge 3 wire power supply
cord with 3 prong grounded plug.
- Neer C-500 7/8 inch strain relief.
- 3 wire connectors.
- Part No. 302797 grommet
Follow the kit instructions for installing the power
supply cord.
o Power supply cord must plug into a mating three prong,
grounded outlet, located in the cabinet next to the
dishwasher opening. Outlet must meet all local codes and
ordinances.
installation instructions
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
1. Disconnect power.
2. Turn off water supply.
Prepare cabinet opening using
existing utility hookups
e Follow the steps in this section if you are installing the
dishwasher in an existing cabinet opening with utility
hookups.
e If you are installing the dishwasher in a cabinet opening
that does not have hookups, follow the steps under
"Prepare cabinet opening where there are no existing
utility hookups" section.
1. Check that the water
line reaches to the
front left of opening
where the water
connection will be
made.
2. Check that the direct _
wire reaches to the
front right of opening 6" (15.2 cm)
where the electrical ....... _--_
connection will be made.
If the water line and the direct wire reach far enough into
the opening, proceed to the next section "Install the drain
hose." If they do not reach far enough, follow the steps
under "Prepare cabinet opening where there are no
existing utility hookups:'
install the drain hose
IMPORTANT: Always use a new drain hose even when
installing a new replacement dishwasher.
1. Drill a 1-1/2" (3.8 cm) diameter hole in cabinet wall or
floor on the side of the opening closest to the sink.
2. Connect drain hose to waste tee or waste disposer
using one of the following methods:
o Option 1, Waste disposer- with air gap
o Option 2, No waste disposer- with air gap
o Option 3, Waste disposer- no air gap*
o Option 4, No waste disposer- no air gap*
+anair gap is recommended
HelpfuITip:To reduce the vibration of the hose, keep
the hose away from the floor and the edge of the hole
where it passes through the cabinet.
Option 1, Waste disposer - with air gap:
1. Remove the disposer knockout plug. Cut end of drain
hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type
clamp. If the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp +.
3. Use a rubber hose connector + with spring or screw-
type clamps + to connect air gap to disposer inlet.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed.
drain hose -
cut hereif needed
rubberhose
connector
+/air gap
spring-type
clamp
hose
drain trap
4. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
+ Parts available from local plumbing supply stores
Option 2, No waste disposer - with air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to air gap with large spring-type
clamp. If the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp s,
3. Use a rubber hose connector* with spring or screw-
type clamps* to connect air gap to waste tee.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed.
drain hose-
_cut here if needed
rubber hose
connector
large
spring-type
waste
tee drain
drain trap hose
4. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
r' Parts available from local plumbing supply stores
Option 3, Waste disposer - no air gap:
1. Remove the disposer knockout plug. Do not cut end of
drain hose.
2. Attach drain hose to disposer inlet with large spring-
type clamp.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed. It is recommended that the drain hose
be looped up and securely fastened to the underside of
the counter.
large spring-type
clamp
drain hose
disposer
inlet
drain trap
3. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
Option 4, No waste disposer - no air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to waste tee with 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp s.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed. It is recommended that the drain hose
be looped up and securely fastened to the underside of
the counter.
drain hose -
_ cut here if needed
__ screw-type clamp
waste [ "_ "_
tee ' [_ I _
I I drain
kJ ] _ _ hose
dra,n trap JII
3. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
r' Parts available from local plumbing supply stores
Prepare cabinet opening where there
are no existing utility hookups
Electrical connection
Option1, Direct wire method:
HelpfulTip: Wiring the dishwasher will be easier if you
route wire into the cabinet opening from the right side.
1. Drill a 3/4" (1.9 cm) optional preferred
hole in right-hand locations locations
cabinet side, rear or
floor. Preferred and
optional locations are
shown.
2. Wood cabinet: Sand
hole until smooth.
3.
4.
5.
Metal cabinet: Cover
hole with grommet, not provided.
Run wire into house wiring junction box.
Install a U.L-listed/CSA-certified clamp connector
(strain relief) for flexible-type wire. If installing conduit,
attach a U.L.-listed/CSA-certified conduit connector to
the junction box.
Run other end of wire
through cabinet hole.
Cable must extend to the
right front of cabinet
opening.
Option2, Powersupplycord method:
NOTE: A mating, three prong, ground-type wall receptacle
is required in a cabinet next to the dishwasher opening.
1. Drill a 1-1/2"
I
(3.8 cm) hole in I optional preferred
the cabinet rear r':"; _ns Ioc_
or side. Preferred '_"
and optional _
,ocat,onsare"::";
shown.
2. Wood cabinet:
Sand hole until
smooth.
Metal cabinet: Cover hole with grommet (Part
No. 302797) included with power supply cord kit.
install the water line
HelpfulTip: Routing the water line through the left side
of cabinet opening will make water connection easier.
Drill a minimum 1/2" (1.3 cm) hole in the cabinet side,
rear or floor. Preferred and optional locations are
shown.
2. Measure overall length
of copper tubing
required.
3. Attach copper tubing
to the water line with a
manual shutoff valve.
copper
tubing
4. Slowly feed copper
tubing through hole in
cabinet. Copper tubing will bend and kink easily, so be
gentle.The copper tubing should be far enough into the
cabinet opening to connect it to dishwasher inlet on the
front left of the dishwasher.
5. Turn water shutoff valve to "ON" position. Flush water
into a shallow pan to get rid of particles that may clog
the inlet valve.
6. Turn shutoff valve to "OFF" position.
install the drain hose
IMPORTANT: Always use a new drain hose.
1. Drill a 1-1/2" (3.8 cm)
diameter hole in
cabinet wall or floor on
the side of the opening
closest to the sink.
2. Connect drain hose to waste tee or waste disposer
using one of the following methods:
, Option 1, Waste disposer- with air gap
, Option 2, No waste disposer- with air gap
, Option 3, Waste disposer- no air gap*
, Option 4, No waste disposer- no air gap*
_'anair gapis recommended
HelpfulTip:To reduce the vibration of the hose, keep
the hose away from the floor and the edge of the hole
where it passes through the cabinet.
Option 1, Waste disposer - with air gap:
1. Remove the disposer knockout plug. Cut end of drain
hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type
clamp. If the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp*.
3. Use a rubber hose connector* with spring or screw-
type clamps* to connect air gap to disposer inlet.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed.
drain hose -
cut here if needed
rubber hose
connector
gap
spring-type
clamp
hose
drain trap
4. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
_'Parts available from local plumbing supply stores
Option 2, No waste disposer - with air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to air gap with large spring-type
clamp. If the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp s,
3. Use a rubber hose connector* with spring or screw-
type clamps* to connect air gap to waste tee.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed.
drain hose-
cut here if needed
rubber hose
connector
large
spring-type
waste
tee drain
drain trap hose
4. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
_' Parts available from local plumbing supply stores
Option 3, Waste disposer - no air gap:
1. Remove the disposer knockout plug. Do not cut end of
drain hose.
2. Attach drain hose to disposer inlet with large spring-
type clamp.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed. It is recommended that the drain hose
be looped up and securely fastened to the underside of
the counter.
large spring-type
clamp
drain hose
disposer
inlet
drain trap
3. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
Option 4, No waste disposer - no air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to waste tee with 1-1/2" to 2"
(3.8 to 5 cm) screw-type clamp s.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed. It is recommended that the drain hose
be looped up and securely fastened to the underside of
the counter.
drain hose -
_ cut here if needed
_ screw-type clamp
_easte/ __ _ra_n
dra,ntrap:--111
3. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
Parts available from local plumbing supply stores
Prepare dishwasher
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
1. Grasp sides of dishwasher door frame and put
dishwasher on its back.
2. Removetwoscrewsattachingaccesspanelandlower
paneltodishwasherusinga 1/4" hex socket, nut driver
or Phillips screwdriver.
3. Remove panels and set panels aside on a protective
surface.
4. Check that grounding clip is attached to the lower
panel.
lower
panel
clip
5. ApplyTeflon _:tape or pipe
joint compound to 90 ° elbow
fitting and connect fitting to
water inlet valve.
6. Tighten elbow until snug, and
be sure that it faces to the
rear.
water inlet valve
7. Remove terminal box cover.
- if you are direct wiring: install a U.L.-listed/CSA-
certified clamp connector to the terminal box. If using
conduit, use a U.L-listed/CSA-certified conduit
connector,
- If you are installing a power supply cord kit, do so
now, following kit instructions.
terminal
/ boxcover
l l_q I\
/
dishwasher wires
HelpfulTip: Put cardboard under dishwasher until it is
installed in cabinet opening.The cardboard will help
protect floor covering during installation.
8.
Measure height of cabinet opening
from underside of countertop to
floor where dishwasher will be
installed (you need the lowest
point). Check chart for that height
opening. Put wheels in the required
position.
Number of
Minimum Wheel
turns on
cutout height position front leg
34" (86.4 cm) 1 10
34-1/4" (87 cm) 2 5
34-1/2" (87.6 cm) 3 0
9.
Turn both front leveler legs to the same
height.
If the minimum cutout height is less than
34" (86.4 cm), the rear wheels can be
removed for additional clearance.This will
allow the dishwasher to fit into a 33-7/8"
(86 cm) high cutout, but the dishwasher
will be more difficult to move into
position. If the wheels are removed,
front leg
protect the floor when moving the dishwasher.
if you have built-up
floors
Measure height of opening
from underside of
countertop to built-up
floor. If the height is at
least 33-3/4" (85.7 cm), the
dishwasher will fit into the
2.
3.
opening without
modification to the
countertop or flooring.
Put wheels in position 1
shim
_/
/ countertop
"T
33-3/4"
(85.7 cm)
rain.
and turn the front leveler legs up all the way.
Add shims as needed in the area shown to bring
dishwasher up to proper height.
NOTE: Shims must be securely attached to floor to
prevent their movement when the dishwasher is
operated.
sh,miiiii ii
(7.0cm)
2"
(5.1 cm)
6"
(15.2cm)
(ZOcm)
lO
Loading...