Estar Fokker Eindecker Instruction Manual

INSTRUCTIONS

www.estarmodels.com

 KIT INCLUDES

 ITEMS NEEDED TO COMPLETE

Full size plan.
Lasercut parts.

3.0mm W100xL600mm plywood : 3sheets

2.0mm W100xL300mm plywood : 1sheet

5.0mm W100xL565mm balsa : 1sheet

5.0mm W100xL365mm balsa : 1sheet

3.0mm W100xL600mm balsa : 1sheet

3.0mm W100xL590mm balsa : 2sheets

3.0mm W100xL465mm balsa : 1sheet

3.0mm W100xL340mm balsa : 2sheets

3.0mm W100xL330mm balsa : 1sheet

1.5mm W100xL525mm balsa : 2sheets

1.5mm W100xL465mm balsa : 2sheets

1.5mm W100xL405mm balsa : 2sheets

1.5mm W100xL230mm balsa : 1sheet

Landing gear (2.0mm Music wire 414, 395, 350mm)
Tail hardware (1.5mm Music wire 220, 72mm, PVC sleeve)
Aileron Pushrods (2ea)
CA hinge
Rubber rings for tire(2ea)
Clear Plastic

Instructions and Stickers.

Download full color instructions from
http://www.estarmodels.com [Download] menu.

CAUTION

Be sure to use suitable power.
Too much power makes this plane unstable.

Brushless Motor (Max 20A/220W)
Brushless ESC 30A
Slow Propeller 1047~1147

Receiver (4ch Min.)
4 submicro Servos

Li-Poly 3s(11.1V) 1800mAh Battery

One and half rolls of covering film.

Thick nylon thread, rubber bands
EZ connectors (2ea) and Wheel Collars (4ea)

Page 1

 PREPARATION



Remove parts from laser-cut panel and group as shown
above.

 VERTICAL TAIL

1. Lay waxed paper or PE film over the plan.

Pin the vertical tail parts(R1-R5) on the plan and glue
together with thick CA.

2. Remove vertical tail from the plan and glue the parts(R6­R7). Apply thick CA glue at each joints for reinforcing.

3. Carefully sand surfaces.

 HORIZONTAL TAIL

1. Lay waxed paper or PE film over the plan.

Pin the horizontal tail parts(E1-E8) on the plan and glue
together with thick CA.
Use scrap balsa as a supports for the edge parts.

2. Remove horizontal tail from the plan and glue the
capstrips(E9). Cut PVC sleeve(L=75mm) and insert to the
hole of ribs and glue it.

3. glue the leading and trailing edge (E10-E11).
Apply thick CA glue at each joints for reinforcing and then
carefully sand surfaces.

Page 2

 RIGHT WING

1. Glue rear spars (W10) together with thick CA.

2. Lay waxed paper or PE film over the plan.

Pin fore lower spar(W9), rear lower spar(W10), trailing
edge(W12) on the plan. Use scrap balsa as a supports for
the spars.
Assemble wing ribs(W1-W5).

3. Assemble fore riblets(W7-W8), upper spars(W9-W10),
wingtip(W13) and wingtip rib(W6).
Glue together with thick CA.

4. Glue wingroot upper panels(W19-W21), small
sheets(W22), servo trays(W23), gusset(W26) and wingtip
support(W13A).

5. Glue wingroot lower panels (W16-W18), small
sheets(W22), servo bay(W24), leading edge(W14) and
wingtip trailing edge(W15).
Apply thick CA glue at each joints for reinforcing.

 LEFT WING

1. Assemble left wing as same way of right wing.

2. Carefully sand surfaces.

 AILERONS

1. Lay waxed paper or PE film over the plan.

Pin trailing edge(A4)and small sheets(A6) on the plan and
assemble aileron ribs(A2-A3), tip(A5), sub leading
edge(A1), gusset(A9) and leading edge(A7).

2. Apply thick CA glue at each joints for reinforcing and
then carefully sand surfaces.

3. Assemble left aileron as same way of right aileron.

Page 3