Esse-ti Helpy GSM, Helpy GSM-RM Quick Manual

15/09/2017

Alarm system for elevators

QUICK GUIDE

Page 2 INSTALLING

INSTALLING

A Internal power-supply connector

B Built-in backup battery connector

C Antenna cable connector

D Reset pushbutton

E Alarm pushbutton

F SIM Card slot with front panel

G Built-in loudspeaker connector

H Serial port for PC connection

I (not present)

L RJ11 connector for local telephone

M Battery compartment door

N Terminal blocks

O Built-in microphone

INSTALLING Page 3

LED signalling alarm / periodical test call (yellow)

LED signalling GSM signal strength (green)

LED signalling GSM status (red)

LED signalling power supply status (blue)

Terminal blocks

N. NAME DESCRIPTION

01 +

POWER SUPPLY INPUT (11-14VDC)

(1)

02 –
03 AIP GIVEN ALARM INDICATOR LIGHT (output: 12VDC)
04 ARP RECEIVED ALARM INDICATOR LIGHT (output: 12VDC)
05 +12 12VDC OUTPUT (max. 100mA)
06 C COMMON TERMINAL FOR INPUT ALC

(2)

07 – NEGATIVE POLE
08 ALC ALARM INPUT FOR THE ELEVATOR CAR

(3)

09 ALY ALARM INPUT FOR THE PIT

(4)

10 IN1 FILTER INPUT

11 ALT2

OUTPUT FOR CONNECTING THE LOUDSPEAKER OF A PASSIVE
HANDSFREE TERMINAL

12 MIC2

INPUT FOR CONNECTING THE MICROPHONE OF A PASSIVE HANDSFREE
TERMINAL OR A SINGLE MICROPHONE

13 MIC3

INPUT FOR CONNECTING THE MICROPHONE OF A PASSIVE HANDSFREE
TERMINAL OR A SINGLE MICROPHONE

14

–

NEGATIVE POLE
15 TEL LOCAL TELEPHONE
16 RL1 RELAY

(5)

17 RL1 RELAY

(5)

18 VVX OUTPUT FOR CONNECTING AN ADDITIONAL ACTIVE HANDSFREE TERM.
19 VVY OUTPUT FOR CONNECTING THE PIT ACTIVE HANDSFREE TERMINAL
20 ALZ ADDITIONAL ALARM INPUT

(4)

OR AUXILIARY INPUT

(5)

21 AIN GIVEN ALARM INDICATOR LIGHT (output: 0VDC)
22 ARN RECEIVED ALARM INDICATOR LIGHT (output: 0VDC)
23 C-L CAN-BUS
24 C-H CAN-BUS
25 TX RS-232
26 RX RS-232
27

–

NEGATIVE POLE
28 C1 COMMON TERMINAL FOR INPUT IN1

(2)

(1)

: before using this input disconnect the internal power-supply cable from the A

connector in the picture at page 2

(2)

: can be connected to a block –, to the block +12 or to an external reference

(3)

: allows to connect voltage free contact pushbuttons (NO or NC) or powered

pushbuttons

(4)

: allows to connect voltage free contact pushbuttons (NO)

(5)

: free contact NO

Page 4 INSTALLING

INSERTING THE SIM CARD

Before inserting the SIM card, make sure the device is off and use all due
precaution to avoid electrostatic discharge.

 Remove the cover by unscrewing the two screws.
 Push the SIM Card housing cover as indicated by the arrow OPEN until it

unlocks and lift it.

 Carefully slide the SIM Card into its housing cover.
 Lower the SIM Card housing cover and push it as indicated by the arrow

LOCK until it locks in place.

ATTENTION

It is not required to remove the PIN code prior to

the use of the HelpyGSM.

The PIN code can be entered, if necessary, by

setting parameter 282.

INSTALLING THE ANTENNA

 Screw the antenna extension cable provided in the appropriate

connector.

ATTENTION

Position the antenna with magnetic base so that any

metal surfaces do not block the signal.

ATTENTION

In order to avoid damage, never power up the base

station without having first installed the antenna.

ATTENTION

Do not install the product in the immediate vicinity
of other electrical or electronic equipment that was

not designed to be combined with it and that could

cause disturbance or interference.

INSTALLING Page 5

CONNECTING THE HANDSFREE TERMINALS

HelpyGSM comes with a built-in active handsfree terminal.
It is also possible to connect to the HelpyGSM:

- up to 2 independent active handsfree terminals

- up to 2 passive handsfree terminals (or cables with microphone) combined

to the integrated active handsfree terminal.
It makes HelpyGSM extremely flexible and allows to realize many different
types of installation.

Note:

an active handsfree terminal allows to realize an independent

voice point with dedicated pushbutton.

Note:

a passive handsfree terminal must be connected to an active

handsfree terminal and allows to double it. The passive
handsfree terminal can be installed at max 6m distance from
HelpyGSM (or from another active handsfree terminal) by
using a shielded cable.

Note:

in case of connection of active handsfree terminals, the type of

installation must be defined (by setting parameters 63 and

73).

 Connect the handsfree terminals (beware of terminal polarity):

ACTIVE HANDSFREE terminal blocks HELPYGSM terminal blocks

+ VVY or VVX

– –

PASSIVE HANDSFREE terminal blocks HELPYGSM terminal blocks

A ALT2

B MIC2 or MIC3
– –

Examples of types of installation

Installation with passive handsfree terminal in the elevator car
bottom

DEVICE

HANDSFREE

terminal blocks

PUSHBUTTON

terminal blocks

ROOF HelpyGSM Built-in active handsfree Built-in pushbutton

CAR Microphone cable

MIC3 /

– ALC / –

CAR BOTTOM Passive handsfree ALT2 /MIC2 / – ALY / –

PROGRAMMING CODES "TYPE OF INSTALLATION" TO BE SET

631 (factory) 730 (factory)

Page 6 INSTALLING

Installation with active handsfree terminal in the pit

DEVICE

HANDSFREE

terminal blocks

PUSHBUTTON

terminal blocks

ROOF HelpyGSM Built-in active handsfree Built-in pushbutton

CAR Microphone cable MIC3 / – ALC / –

PIT Active handsfree

VVY /

– ALY / –

PROGRAMMING CODES "TYPE OF INSTALLATION" TO BE SET

632 730 (factory)

Installation with landing floors

DEVICE

HANDSFREE

terminal blocks

PUSHBUTTON

terminal blocks

ROOF HelpyGSM Built-in active handsfree Built-in pushbutton

CAR Microphone cable

MIC3 /

– ALC / –

CAR BOTTOM Passive handsfree

ALT2 /MIC2 /

– ALC / –

LANDING FLOOR 1 Active handsfree VVY / – ALY / –

LANDING FLOOR 2

Passive handsfree terminal combined to the active

handsfree terminal positioned in the landing floor 1

ALY / –

LANDING FLOOR 3 Active handsfree VVX / – ALZ / –

LANDING FLOOR 4

Passive handsfree terminal combined to the active

handsfree terminal positioned in the landing floor 3

ALZ / –

PROGRAMMING CODES "TYPE OF INSTALLATION" TO BE SET

633 730 (factory)

Installation with independent handsfree terminals on car-top /
car-cabin / pit

DEVICE

HANDSFREE

terminal blocks

PUSHBUTTON

terminal blocks

ROOF HelpyGSM Built-in active handsfree Built-in pushbutton

CAR Active handsfree

VVX /

– ALC / –

PIT Active handsfree VVY / – ALY / –

PROGRAMMING CODES "TYPE OF INSTALLATION" TO BE SET

633 731

Installation with HelpyGSM installed in the machine room

DEVICE

HANDSFREE

terminal blocks

PUSHBUTTON

terminal blocks

MACHINE ROOM HelpyGSM Built-in active handsfree Built-in pushbutton

ROOF

Passive handsfree terminal combined to the car

active handsfree terminal

ALZ / –

CAR Active handsfree

VVX /

– ALC / –

PIT Active handsfree VVY / – ALY / –

PROGRAMMING CODES "TYPE OF INSTALLATION" TO BE SET

633 731

INSTALLING Page 7

CONNECTING THE EMERGENCY CALL BUTTONS

Car pushbutton

It is possible to connect (inside the elevator car) voltage free contact
pushbuttons or powered pushbuttons.

 Connect, following one of the diagrams shown below, the car

pushbutton.

Voltage free contact pushbuttons

Powered pushbuttons (12~24Vdc) – 2 solutions

Page 8 INSTALLING

Other pushbuttons

It is possible to use for the pit, the car-top or the landing floors, voltage free
contact pushbuttons (NO).

 Connect, following the diagram shown below, the other pushbuttons.

INSTALLING Page 9

CONNECTING THE INDICATOR LIGHTS

The GIVEN ALARM INDICATOR LIGHT (yellow) switches on after pressing
the emergency button to indicate the beginning of the alarm procedure and
stays steady light until the end. The RECEIVED ALARM INDICATOR
LIGHT (green) switches on when the alarm call is answered.

 Connect, following one of the diagrams shown below, the indicator

lights.