ESPRIT X5 Owner's Manual
-ESP0033-
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR ELLIPTICAL!
OWNER’S MANUAL
Esprit X5 Cross Trainer
1
WARNING - Read all instructions before using this appliance.
■
Do not operate elliptical on deeply padded, plush or shag carpet. Damage
to both carpet and elliptical may result.
■
Keep children away from the elliptical. There are obvious pinch points and
other caution areas that can cause harm.
■
Keep hands away from all moving parts.
■
Never operate the elliptical if the elliptical is not working properly; call your
dealer.
■
Never drop or insert any object into any openings.
■
Do not use outdoors.
■
Do not attempt to use your elliptical for any purpose other than for the
purpose it is intended.
■
The pulse sensors are not medical devices. Various factors, including the
user’s movement, may affect the accuracy of heart rate readings. The pulse
sensors are intended only as exercise aids in determining heart rate trends
in general.
■
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not
suitable for use on your elliptical. Quality athletic shoes are recommended
to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
CAUTION!! Please be careful when un-packing the carton.
ESP0033/ X5_ver. A
Safety Hints
2
Assembly Pack Check List
#44- 5/16” Flat
Washer (8pcs)
#45- 5/16" Curved
Washer (1pc)
#43- 5/16" × 3/4" Button
Head Socket Bolt (13pcs)
#53- M5 × 12 mm Phillips
Head Screw (4pcs)
STEP 1.
STEP
2.
STEP
3.
#43- 5/16" × 3/4" Button
Head Socket Bolt (1pc)
#92- 8.5x23x1.5T
Flat Washer (1pc)
#46- 5/16" Split
Washer (9pcs)
#
55- 5/16"
Nyloc Nut (2pcs)
#43- 5/16" × 3/4" Button
Head Socket Bolt (1pc)
#92- 8.5x23x1.5T
Flat Washer (1pc)
#55- 5/16"
Nyloc Nut (2pcs)
#56- 5/16" ×1-3/4" Button
Head Socket Bolt (2pcs)
#56- 5/16" ×1-3/4" Button
Head Socket Bolt (2pcs)
#89- M5 × 65m/m Phillips
H
ead Screw (1pcs)
3
Assembly Pack Check List
STEP
4.
#67- Combination M5 Allen Wrench &
Phillips Head Screw Driver (2pcs)
#68- 19m/m Wrench (1pc)
#91- 5/16" × 1" Button
Head Socket Bolt (2pcs)
#44- 5/16” Flat
Washer (2pcs)
#30- 1/2" Nyloc
Nut (2pcs)
#29- 1/2" × 70mm
Carriage Bolt (2pcs)
#46- 5/16" Split
W
asher (2pcs)
4
STEP 1:
1. Install the Steel Cable Assembly (59) on the Console Mast (2) using 1pcs of M5 ×
65m/m Phillips Head Screw (89) to tighten.
2. Locate the Console Mast (9) and slide on Console Mast Cover (79). Make sure the
cover is facing the correct direction, as shown below, before sliding onto mast. Install
the wiring harness (90) into the bottom of the mast and out the top. Be careful when
installing the console mast to the mainframe so as not to pinch or cut the wiring
harness; damage to the console may occur.
3. Install the console mast on the mainframe using the M5 Allen Wrench (67) to tighten
5pcs of 5/16” Button Head Socket Bolts (43), 4pcs of 5/16” Flat Washers (44), 5pcs of
5/16" Split Washers (46) and 1pc of 5/16" Curved Washer (45). Snap the Console
Mast Cover (79) in place on the body of the elliptical.
4. Route the hand pulse wires (90) from the stationary handle bars (10, 11) through
Console Mast (9) as shown below. Use M5 Allen Wrench (67) to tighten 4pcs of 5/16”
Button Head Socket Bolts (43) to secure both handles on the Console Mast (9).
5. Connect the cables (62, 90) to the Console (58) and install console onto the Mast (9)
with 4pcs of M5 × 12L Phillips head screws (53) by using the Phillips Head Screw
Driver (67).
6. Secure Front Stabilizer (12) and Rear Stabilizer (13) with 4pcs of 5/16” Button Head
Socket Bolts (43), 4pcs of 5/16" Split Washers (46) and 4pcs of 5/16” Flat Washers (44)
by using M5 Allen Wrench (67).
Assembly Instructions
5
Loading...