Page 1
040-00062-01 REV 2
X Games Snowboarder™ Operator’s Manual
Snow Boarder TM © 2017 Raw Thrills, Inc. All Rights Reserved. © 2017 ESPN, Inc.
ESPN, X Games, the X Games logo, etc. registered trademarks of ESPN, Inc.
Page 2
Page 3
Snowboarder™ Operator’s Manual
Table of Contents
Safety .................................................................................................................................................................... 5
Operation ......................................................................................................................................................... 5
Transporting .................................................................................................................................................... 5
Handling Components .................................................................................................................................... 5
Disconnect Power ............................................................................................................................................ 5
Grounding ........................................................................................................................................................ 5
Electrical Shocks .............................................................................................................................................. 5
Monitor ............................................................................................................................................................ 5
Power Selector ................................................................................................................................................. 5
Power Cord ...................................................................................................................................................... 5
Surge Suppressor ............................................................................................................................................ 6
Water and Other Liquid Sources .................................................................................................................... 6
Connectors ....................................................................................................................................................... 6
Computer ......................................................................................................................................................... 6
Tempered Glass Warning ............................................................................................................................... 6
Hazard to Epileptics ........................................................................................................................................ 6
Manual .............................................................................................................................................................. 6
Specifications ................................................................................................................................................... 6
Product Specifications .......................................................................................................................................... 7
Electrical Power ............................................................................................................................................ 7
Dimensions ................................................................................................................................................... 7
Operating Temperature ................................................................................................................................ 7
Operating Humidity ...................................................................................................................................... 7
Fuse Replacement Guide ...................................................................................................................................... 7
RIO ................................................................................................................................................................ 7
Game Lighting ............................................................................................................................................... 7
Setup ..................................................................................................................................................................... 8
Cabinet Assembly .............................................................................................................................................. 8
Check Electrical Settings ................................................................................................................................... 8
Startup Game .................................................................................................................................................... 8
Diagnostics and Adjustments .............................................................................................................................. 11
Service Panel ................................................................................................................................................... 11
3 | Page
Page 4
Snowboarder™ Operator’s Manual
Test Menu Navigation ..................................................................................................................................... 11
Test Menus ..................................................................................................................................................... 12
Main Menu.................................................................................................................................................. 12
Basic Functional Test on Initial Power Up ....................................................................................................... 20
PC Hardware ....................................................................................................................................................... 21
HP Elitedesk 705 G3 MT BIOS ......................................................................................................................... 21
PC Hard Drive Recovery .................................................................................................................................. 22
Troubleshooting .................................................................................................................................................. 23
Technical Support ............................................................................................................................................... 27
Electrical and Mechanical Illustrations ............................................................................................................... 29
4 | Page
Page 5
Snowboarder™ Operator’s Manual
Safety
Operation
Before operating game, read this manual. Failure to properly install and operate this game could result in
malfunction or accident. Operate the game in accordance with the manual.
Transporting
The cabinet is very heavy. Because the monitor is high, the cabinet is also very top-heavy. Use appropriate
care when moving or transporting cabinet. It contains fragile glass and electronic components. Avoid rough
handling.
Handling Components
Many components are extremely sensitive to handling, environmental and Electrostatic Discharge (ESD)
events—especially the computer. Do not handle it roughly. Before servicing, call your distributor and inquire
about the PC warranty. Use proper ESD procedures when servicing. Protect components from harmful
environmental conditions, such as extreme temperatures, excessive moisture or other damaging effects.
Disconnect Power
Always turn the power off and unplug the unit before servicing or making adjustments unless otherwise
instructed. Installing or repairing components while power is on can damage the components and void the
warranty.
Grounding
Avoid electrical shock. Do not plug in AC power until you have inspected and properly grounded the unit.
Only plug into a grounded, three-wire outlet. Do not use a “cheater” plug or cut off the ground pin on the line
cord.
Electrical Shocks
There is no isolation transformer in the cabinet. Disconnect AC power before servicing. However, be aware
that lethal voltages can remain in the electronic components even when AC power is disconnected. Use
extreme caution when servicing. Verify that there is a working ground connection. If the unit sustains water
damage, cease using it immediately and unplug AC power.
Monitor
The monitor contains no user serviceable parts. Do not attempt to service the monitor.
Power Selector
Before installing game, ensure the voltage on the PC and power supply is set properly. There is a 115/230
VAC selector switch that must be set for the correct voltage for your site. The setting must match the line
voltage at the installation site.
Power Cord
If the power cord is damaged or lost, replace it with an identical cord as supplied by the manufacturer or an
authorized service agent.
5 | Page
Page 6
Snowboarder™ Operator’s Manual
Surge Suppressor
It is recommended that you plug your game’s power cord into a surge suppressor to help protect from power
surges that may damage sensitive electronic components.
Water and Other Liquid Sources
Do not install game near sprinkler or other water jet sources. Do not use water jet to clean game. Keep
minimum clearance behind game and wall for proper ventilation but also prevent access of liquid from spills
and sprays from entering ventilation holes.
Connectors
When servicing machine, ensure all connectors mate properly. If connectors do not slip in easily, do not force
them. Connectors are often keyed and only connect one way. Check for correct orientation.
Computer
The computer contains sensitive components, including a hard drive. Do not handle it roughly. Call your
distributor before servicing its internal components. Ask about warranty information as it relates to the PC.
Do not turn the PC power switch on or off. It should remain permanently in the ON position.
Cycle AC power on or off with the cabinet power switch.
A dongle has been inserted into one of the USB ports. This is required for game play.
Do not remove the dongle except for troubleshooting purposes.
Tempered Glass Warning
When handling the LCD display glass cover take especial care and set the glass down softly on a flat surface
free of debris. The edge of the glass is sensitive to hard impact. Shattered glass from the can travel long
distances and cause bodily injury. Use proper procedures when handling broken materials.
Hazard to Epileptics
A small portion of the population has an epileptic condition that may cause seizures. Affected persons
experience seizures while watching some television pictures or playing certain video games. People who have
not had seizures may still have an undetected epileptic condition. If anyone in your family has experienced
epilepsy symptoms (seizures or loss of awareness), consult your physical before using video games. While
children play video games, a parent should observe. Be alert to the following symptoms: dizziness, altered
vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation or convulsions. If
you or your child experiences these symptoms, discontinue use immediately and consult your physician.
Manual
Keep this manual available and ready for use. Please check our website www.rawthrills.com for the latest
information regarding this and other Raw Thrills products. If the game fails to function properly, turn off the
machine and unplug the AC line cord. Contact your local distributor. Your warranty, when applicable, lasts 60
days from your purchase date. You may not reproduce this document or any of its contents without written
authorization from Raw Thrills, Inc. or Play Mechanix™ Inc.
Specifications
For reasons, such as performance, this product’s specifications may change without notice. Federal patent,
copyright and other intellectual property laws protect the content, devices and design of the game and its
equipment.
6 | Page
Page 7
Snowboarder™ Operator’s Manual
Product Specifications
Electrical Power
United States, International, and Japan
Operating AC Current: 5/2.5 Amps
Voltage: 115/230 ~ VAC 50/60Hz
Inrush AC Current: 7 Amps
Dimensions
Height with Marquee Topper: 104” (2.64 Meters)
Height without Marquee Topper: 81” (2.06 Meters)
Width: 43.5” (1.10 Meters)
Depth: 77” (1.96 Meters)
Operating Temperature
50 ⁰F to 104 ⁰F
(10 ⁰C to 40 ⁰C)
Operating Humidity
Must not exceed 95% relative humidity
Fuse Replacement Guide
NOTE: FOR CONTINUED PROTECTION AGAINST
FIRE AND ELECTRICAL DAMAGE, USE ONLY
SPECIFIED FUSE TYPE AND VALUE.
RIO
5VDC = 3A 250V SLO-BLO
12VDC = 5A 250V SLO-BLO
Game Lighting
5A 250V SLO-BLO (x6)
7 | Page
Page 8
Snowboarder™ Operator’s Manual
Setup
Cabinet Assembly
Note: See foldout setup guide.
1. Begin assembly by aligning Snowboard pedestal up to the cabinet and connecting all electrical
cables. Secure pedestal to cabinet with (2x) mounting brackets.
2. Identify the left and right side panel assemblies and place in position by aligning their bottoms with
cutouts in pedestal. Secure the outside of each side panel to cabinet and pedestal.
3. Secure the inside of each side panel to the cabinet and control panel.
4. Slide marquee metal struts into holes in top of cabinet and connect all electrical cables. Secure
marquee to cabinet.
Check Electrical Settings
1. Verify the voltage of the AC outlet you will be plugging the game into.
2. Verify the AC outlet’s ground connection is present and working.
Startup Game
1. Plug the line cord into an AC outlet.
2. Turn the main cabinet power switch on.
3. Verify the game and all components are operating normally. See Basic Functional Test on Initial
Power Up in the Diagnostics and Adjustments section for the recommended procedure.
4. Authorize a set of cards. See Authorizing More Cards under the Cards and Card Dispensers section.
8 | Page
Page 9
Snowboarder™ Operator’s Manual
9 | Page
Page 10
Snowboarder™ Operator’s Manual
10 | Page
Page 11
Snowboarder™ Operator’s Manual
TEST
SERVICE
Volume
Volume
(Service Panel)
Diagnostics and Adjustments
Service Panel
The Service Panel is located behind the coin door and has four buttons that can be used to navigate the Test
Menu system. There is a USB port on the Service Panel that can be used for software updates and audit
downloads.
UP
DOWN
Test Menu Navigation
In addition to the buttons on the Service Panel, you can also us the Start and Gameplay buttons to navigate
through the Test Menus.
Navigating the Test Menu
Button Action
TEST/BACK (Not in Test Menu) Enters Test Menu
TEST/BACK (In Test Menu) Selects Highlighted Option
SERVICE (On Main Menu) Exits Test Menu
SERVICE (Not on Main Menu) Cancels Selection
VOLUME UP Move Up
VOLUME DOWN Move Down
START Selects Highlighted Menu
ARROWS Move Up and Down
11 | Page
Page 12
Snowboarder™ Operator’s Manual
MAIN MENU
DIAGNOSTICS
EXIT
Test Menus
Main Menu
Choose from all available operator settings and menus here.
GAME AUDITS
PRICING ADJUSTMENTS
SYSTEM ADJUSTMENTS
GAME ADJUSTMENTS
UTILITIES
CALIBRATION
VOLUME
ATTRACT VOLUME
COIN VOLUME
12 | Page
Page 13
Snowboarder™ Operator’s Manual
DIAGNOSTICS
SWITCH TEST
WATCHDOG TEST
EXIT
Diagnostics Menu
Choose from all available diagnostics here
SOUND TEST
MONITOR TEST
LIGHT TEST
LINK SYSTEM
COIN METER TEST
BLOWER TEST
• Switch Test: Tests all buttons, inputs, and switches
• Sound Test: Tests speakers and woofers (100Hz Test, 1000Hz Test)
• Monitor Test: Color purity tests
• Light Test: Tests all LED lights on the cabinets
• Link System: Tests whether the game is linked to another SnowBoarder and shows Game ID
• Coin Meter Test: Clicks the “Hard Coin Meter” inside the cabinet
• Blower Test: Tests the air blower motor function
• Watchdog Test: Tests the watchdog reset function
13 | Page
Page 14
Snowboarder™ Operator’s Manual
AUDITS MENU
GENERAL 1
GAMEPLAY 2
EXIT
Game Audits
View all available stored audit data here
GENERAL 2
COURSES
COURSE WINS
PLACES
PLAYERS
GAMEPLAY 1
• Audits Menu Description: The audits menus above allow you to view a large amount of data about
your Snowboarder game. Examples include tracks selected, number of linked games played, where
players finished, average gameplay times, and many other categories.
14 | Page
Page 15
Snowboarder™ Operator’s Manual
PRICING ADJUSTMENTS
FREEPLAY
MONEY UNIT
EXIT
Pricing Adjustments
Choose from all available pricing settings here
COINS/BILL PULSE
COINS/CREDIT
CREDITS TO START
CREDITS TO CONTINUE
MAX CREDITS
CREDITS FOR BONUS
BONUS CREDITS
1ST PLACE FREE GAME
1ST HUMAN FREE GAME
• Free Play: Turn on/off free play
• Money Unit: Change between coins, tokens, or cards
• Coins/Bill Pulse: Adjust the amount of pulses for each coin
• Coins/Credit: Adjust the amount of coins per full credit
• Credits to Start: Adjust the amount of credits needed to start a game
• Max Credits: Adjust the maximum amount of credits a player can stack
• Credits For Bonus: Allows the operator to set a multiple credit purchase amount to award a bonus
credit
• Bonus Credits: Set the amount of bonus credits awarded for multiple credit buys
st
• 1
Place Free Game: Allows the operator to award a free game for placing first in any game
st
• 1
Place Human Free Game: Allows the operator to award a free game for multiplayer first place
15 | Page
Page 16
Snowboarder™ Operator’s Manual
SYSTEM ADJUSTMENTS
LANGUAGE
EXIT
System Adjustments
Choose from all available system adjustments here
MAX NAME LENGTH
BLOWER POWER
CURRENT MACHINE ID
ATTRACT AUDIO
AUTO VOLUME SYNC
QR CODES
GAME VENUE
GAME LOCATION
• Language: Set your language setting here. (English is default)
• Max Name Length: Adjusts how long the high score name entry can be
• Blower Power: Adjust the strength of the air flow from the blower motor
• Current Machine ID: Sets the player ID number of the cabinet for linked play
• Attract Audio: Allows the operator to adjust frequency of attract audio. (On, Off, or Occasionally)
• Auto Volume Sync: Allows the operator to sync volume with other linked Snowboarder games
• QR Codes: Turns on the QR Code high score feature. Allows players to upload high scores to social
media like Facebook and Twitter by scanning code with their cell phone.
• Game Venue: Set your location name so that it appears in QR code scans (Example: “Eugene’s
Arcade”)
• Game Location: Set your city and state so that it appears in QR code scans (Example: Chicago, IL)
16 | Page
Page 17
Snowboarder™ Operator’s Manual
GAME ADJUSTMENTS
GAME DIFFICULTY
START TIME
EXIT
Game Adjustments
Choose from all available game adjustments here
CHECKPOINT TIME
PLAYS FOR RESET
METRIC UNITS
AUTOPILOT
GIRL RACERS
SKIP NAME ENTRY
SKIP SELECT SCREENS
SYNC ALL ADJUSTMENTS
• Game Difficulty: Adjusts the difficulty of the game and the CPU controlled racers
• Start Time: Adjust the amount of time the player starts the game with
• Checkpoint Time: Adjusts the amount of extra time the player gets for reaching a checkpoint
• Plays For Reset: The amount of total plays before the high scores reset
• Metric Units: Allows the operator to enable metric measurements in the game
• Autopilot: Allows the operator to disable the computer assisted steering for inactive players
• Girl Racers: Allows the operator to turn off female racers in the game
• Skip Name Entry: Enable or disable the name entry screen for high scores
• Skip Select Screens: Enable or disable player and track select screens
• Sync All Adjustments: Allows the operator to sync adjustments with all linked Snowboarder games
17 | Page
Page 18
Snowboarder™ Operator’s Manual
UTILITIES MENU
RESET CREDITS
COPY HIGH SCORES
EXIT
Utilities Menu
Choose from all available utilities here
RESET AUDITS
RESET HIGH SCORES
RESET PLAYER STATS
RESET ADJUSTMENTS
RESET LINK SYSTEM
FACTORY RESTORE
VIEW ERRORS
VIEW MESSAGES
COPY ERROR DUMPS
COPY AUDITS/LOGS
COPY MESSAGES
• Reset Credits: Allows you to clear out any credits that are on the game
• Reset Audits: Allows you to clear out all audits data on the game
• Reset High Scores: Restores high scores back to the factory default
• Reset Player Stats: Clears out any stored player data
• Reset Adjustments: Restores all adjustments to factory default
• Reset Link System: Restores your linked game settings to factory default
• Factory Restore: Clears out and restores all game settings and adjustments to factory defaults
• View Errors: View any software errors
• View Messages: View misc. software and system messages (developer use)
• Copy Error Dumps: Allows you to copy any error records to a USB drive
• Copy Audits/Logs: Allows you to copy audit data and game logs to a USB drive
• Copy Messages: Allows you to copy the misc. software and system messages to a USB drive
• Copy High Scores: Allows you to copy high score data to a USB drive
18 | Page
Page 19
Snowboarder™ Operator’s Manual
CALIBRATION
SWING LEFT AND RIGHT
EXIT
MAIN MENU
GAME VOLUME
EXIT
Calibration
Calibrate the Snowboard here
EDGE
CENTER
• Swing Left/Right: Move the snowboard its full range to the left and right to calibrate and press start
• Edge: Edge (Tilt) the board left and right and then press start
• Center: When the first two calibrations are complete, press start
Volume Description (Main Menu)
Adjust all volume audio levels in the main menu
ATTRACT VOLUME
COIN VOLUME
• Game Volume: Set the volume level during gameplay
• Attract Volume: Set the volume level during the attract mode
• Coin Volume: Adjusts the volume of the credit chime
19 | Page
Page 20
Snowboarder™ Operator’s Manual
Basic Functional Test on Initial Power Up
1. Calibrate the Snowboard steering and edging following the on-screen instructions
2. Enter the Input Test and verify all switch inputs are working.
3. Enter the Monitor Test and verify the monitor is working properly.
4. Enter the Sound Test and verify the audio works and is not distorted.
5. Enter the Light Test and verify that all the lights are working properly.
6. Enter the Coin Meter Test and verify the coin meter is working properly.
7. Enter the Scanner Test and verify both Player 1 and Player 2 card scanners are working properly.
8. Enter the Dispenser 1 Test and verify the Player 1 dispenser is working properly.
9. Enter the Dispenser 2 Test and verify the Player 2 dispenser is working properly.
10. Enter the Watchdog Test and verify the game reboots.
Upon a successful reboot, you are ready to adjust pricing, volume and other functions.
20 | Page
Page 21
Snowboarder™ Operator’s Manual
PC Hardware
Your SnowBoarder game uses an HP 705 G3 computer with a GT1030 video card. Any brand of GT1030
should work with your game. Listed below are the recommended BIOS settings for the computer.
NOTE
The computer shipped with the correct BIOS settings. Making changes to the BIOS different from the settings
listed below may adversely affect the game’s functionality.
HP Elitedesk 705 G3 MT BIOS
To Access BIOS Settings:
With the computer powered off, plug a USB keyboard into an open USB slot. Hold the ‘F10’ key and turn the
computer on. Continue holding the ‘F10’ key until the BIOS Setup screen appears.
Note: All settings not listed should remain their default values.
Advanced
+ Boot Options
- After Power Loss ................................. [POWER ON]
- UEFI Boot Order: ...................................... [DISABLE]
- Legacy Boot Order (defaults):
USB
SATA CD
STAT0
NETWORK BOOT
+ Built-in Device Options
- Integrated Video: ..................................... [DISABLE]
Note: After exiting BIOS settings screen, power-cycle the cabinet by using the cabinets main power switch.
21 | Page
Page 22
Snowboarder™ Operator’s Manual
PC Hard Drive Recovery
Symptoms requiring a PC hard drive recovery include:
• File test reports bad or missing files.
• Game fails to finish loading during setup.
• After resetting the AC power, an error is reported.
• Erratic Game or Attract Mode behavior.
The only way to repair corrupt files is to reinstall the software as described below:
Computer
The computer contains sensitive components. Do not handle roughly. Call your distributor before servicing its
internal components. Ask about warranty information as it relates to the PC.
Do not use the PC on/off switch. Turn AC power on or off with the cabinet power switch.
Steps to Re-Install the software:
1. Insert installation media into computer. (USB or DVD)
2. Turn cabinet power OFF and wait 30 seconds.
3. Turn cabinet power ON.
4. If using USB installation, select the desired game from the menu.
5. Follow all onscreen instructions.
6. Once installation is complete, remove the installation media and power-cycle the game.
7. Your game is now restored and ready to go.
22 | Page
Page 23
Snowboarder™ Operator’s Manual
Problem
Possible Cause
Solution
Game not plugged in.
Plug game into AC outlet.
Game not turned on.
Turn on main power switch.
Check and replace fuse. See
Test AC outlet and plug game
PC BIOS set incorrectly.
See BIOS Settings section.
Flash Drive Installer is left
Disconnect Flash Drive Installer
Replace the micro switch on the
switch.
Disconnect the cabinet from AC
Ensure all connections to PCB
are secure. Replace PCB if faulty.
Troubleshooting
Warning: Review the Safety section before making any adjustments to the game.
Game will not power up.
Game fuse is blown.
No power to receptacle.
connected to PC.
Faulty micro switch.
Specification section for fuse
values.
into powered outlet.
and power cycle the game.
button and re-test. Verify that
the wires are connected to the
correct spades on the micro
Buttons do not work.
23 | Page
Faulty wiring.
Faulty PCB.
power. Verify that all wires are
firmly connected to each button
and the PCB. Verify that no
wires are frayed or improperly
shorting to ground. Verify that
wires are connected to the
correct spades on the micro
switches.
Page 24
Snowboarder™ Operator’s Manual
Problem
Possible Cause
Solution
To test a USB port, turn off the
correct USB ports and reboot.
Bad connection.
Check connection to speakers.
Use VOL UP button on Test
panel to raise volume
Verify all wires are firmly
improperly shorting to ground.
Remove the grill and inspect
Operator Menu to verify each
A weak or low muffled sound is
each speaker.
To verify audio is working at the
Check external DC supply and
Check all ground wires in
Neither buttons nor audio
work.
PCB connected to faulty USB
port (boot message may indicate
not detected)
Volume set too low.
Faulty wiring.
game, disconnect the device
from the port, and then connect
the game dongle to the port.
Reboot the game. A No Dongle
message indicates the port is
bad. If the game starts, the port
is working. After the test,
reconnect all devices to the
connected to the speakers, PCB,
and green computer audio port.
Verify that each wire is
connected to the correct port
and no wires are frayed or
No sound or bad sound.
Constant low audio hum.
Blown speakers.
Reversed wires.
Faulty PCB.
Faulty power supply.
Open ground.
each speaker for visible damage.
Run
the Sound Test from System
Tests in the
speaker is working.
a sign of reversed speaker wires.
Check for reversed wires on
computer, connect stereo
headphones to the green
computer audio port.
the PC supply.
cabinet. Ensure AC wall outlet is
properly grounded
24 | Page
Page 25
Problem
Possible Cause
Solution
Game does not load.
PC Drive test reports “bad” or
“missing” files.
Game fails to finish loading.
After resetting, game still
Erratic game mode or attract
mode.
WARNING!
Mode and Run “File Test.”
Game Resets
Bad file.
Run Flash Installer.
Check wiring from meter to RIO
board.
Faulty meter.
Replace coin meter.
Blown fuse(s) on PCB
Replace 12vdc 5A fuse(s) on
PCB.
Incorrect setting in Pricing
Disconnect cabinet from AC
Verify coin mech is not jammed.
Exits Test Mode every 3
seconds.
Slide or toggle button off after
Test Menu appears
Snowboarder™ Operator’s Manual
reports an error.
Data files Corrupted.
(Game Operation May Become
Unstable.)
Use “Test” Switch to Enter Test
Coin meter does not click
during test.
Improper number of credits
given when coins or bills are
inserted.
PC hard drive failure.
No pulse to meter.
Adjustments.
Faulty wiring.
Recover hard drive.
See Flash Installer Document or
contact your distributor for the
latest software revision.
Adjust pricing settings.
power. Verify wires are firmly
connected to coin mech and bill
validator and ground wires are
properly connected. Verify no
wires are frayed or shorting to
ground.
25 | Page
Faulty coin mech.
Test button stuck in ON position.
Ensure coin mech is properly
aligned and latched to coin
door.
Page 26
Snowboarder™ Operator’s Manual
Problem
Possible Cause
Solution
Turn PC power switch on.
Dongle missing or disconnected.
Find dongle cable and reseat in
USB port.
Faulty USB port.
Insert dongle cable in different
USB port.
Bad Potentiometer
Replace Potentiometer
Out of Calibration
Calibrate Snowboard
Bad Blower Motor
Replace Motor
Bad wiring or voltage
Check wiring connections and
voltage levels
USB cable disconnected.
Check USB connection from PC to
RIO board.
No Power to RIO board.
Check for proper voltage (+5V,
+12V) at RIO P1 connector.
No Video
Dongle Not Present
Steering or Edging of
Snowboard not working properly
Blower Motor not working
properly
PC not turned on.
Video cable not secure.
Ensure IEC cable tightly plugged
in. Trace cable back to source to
ensure continuity.
Check and secure DVI or HDMI
connector to Monitor. Check
and secure DVI or HDMI
connector to PC.
Connect RIO Board or RIO Board
Missing.
26 | Page
Page 27
Snowboarder™ Operator’s Manual
Technical Support
For an authorized distributor near you, check the Raw Thrills website at www.rawthrills.com
Betson’s Raw Thrills Technical Support Hotline
Phone: 1-800-753-2513
FAX: 1-201-438-5019
Email: rtsupport@betson.com
27 | Page
Page 28
Page 29
Snowboarder™ Operator’s Manual
Electrical and Mechanical Illustrations
29 | Page
Page 30
2
3
4
1
43.020
80.375
103.341
76.845
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
SNOWBOARD-MAIN-CAB-ASSY SNOWBOARD-MAIN-CAB-ASSY
1
2
SNOWBOARD-PED-ASSY SNOWBOARD-PED-ASSY
1
3
ROTO-LEFT-SIDE-PANEL-ASSY
SNOWBOARD-LEFT-ROTO-SIDE-PANEL-ASSY
1
4
ROTO-RIGHT-SIDE-PANEL-ASSY
SNOWBOARD-RIGHT-ROTO-SIDE-PANEL-ASSY
1
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6/6/2017
A
PRODUCTION RELEASE
9/6/2017
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
NEXT ASSY
USED ON
APPLICATION
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
INTERPRET GEOMETRIC
TOLERANCING PER:
MATERIAL
FINISH
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
RAW THRILLS, INC
TITLE:
SIZE
B
REV
WEIGHT:
SCALE: 1:22
UNLESS OTHERWISE SPECIFIED:
A
MG
SNOWBOARD-
FINAL-ASSY
SHEET 1 OF 1
SNOWBOARD-FINAL-ASSY
DO NOT SCALE DRAWING
DWG. NO.
Page 31
13
19
22
22 27
26
6
3
11
20
4
25
2
29
28
9
23
15
15
23
1
18
30
21
24
43.040
80.188
103.137
12
7
31
32
10
14
8
16
17
5
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
601-00793-01
ASSY-MAIN-CAB-SNOWBOARD
1
2
SNOWBOARD-LCD-ASSY SNOWBOARD-LCD-ASSY
1
3
SNOWBOARD-BLOWER-ASSY SNOWBOARD-BLOWER-ASSY
1
4
SNOWBOARD-MARQUEE-ASSY SNOWBOARD-MARQUEE-ASSY
1
5
FAN-BRACKET-ASSY FAN-BRACKET-ASSY
1
6
ROTO-CONTROL-PANEL-ASSY ROTO-CONTROL-PANEL-ASSY
1
7
POWER-PLATE-ASSY POWER-PLATE-ASSY
1
8
600-00905-01 & 600-00906-01
1"WD NYLON STRAP & 1" BUCKLE CLASP
2
9
MARQUEE-REFLECTOR-ASSY MARQUEE-REFLECTOR-ASSY
1
10
SNOWBOARD-WOOFER-ASSY
JP-55-WOOFER-ASSY
1
11
SNOWBOARD-REAR-DOOR-ASSY SNOWBOARD-REAR-DOOR-ASSY
1
12
SNOWBOARD-RIO-HARDWARE-ASSY
RIO Mounting Plate (w/ Blower PCB)
1
13
800-00005-01
MID-WIDTH COINDOOR - BBHD
1
14
HP6005
HP 6005 PC ASSY
1
15
2-1-10-00-00-000
5.25 FULL RANGE SPEAKER
2
16
800-00001-00
120mm Wire Fan Guard
1
17
820-00001-00
FAN, 120VAC,19/15W
1
18
LED-TMOLDING
APPROX-47.68"LG
2
19
600-01972-01
WRAP-COIN-DOOR-SNOWBOARD
1
20
600-01973-01
DOOR-LCD-SNOWBOARD
1
21
600-01974-01
TRIM-LCD-SHELF-SNOWBOARD
1
22
600-01975-01
TRIM-LOWER-BASE-SNOWBOARD
2
23
600-01976-01
GRILL-MARQUEE-SNOWBOARD
2
24
600-01989-01
TRIM-LOWER-MARQUEE-SNOWBOARD
1
25
600-01990-01
TRIM-UPPER-MARQUEE-SNOWBOARD
1
26
600-02077-01
BRACKET-LEFT-ROTO-CAB-SNOWBOARD
1
27
600-02078-01
BRACKET-RIGHT-ROTO-CAB-SNOWBOARD
1
28
603-00820-01
PETG-MARQUEE-SNOWBOARD
1
29
606-01288-01
TRANSLITE-MARQUEE-SNOWBOARD
1
30 LED-RGB-STRIP-FOR-TMOLDING-SNOWBOARD
LED-RGB-STRIP-120CM-SNOWBOARD
2
31
330-00002-01
150W-24V-POWER-SUPPLY-MEANWELL
1
32
500-00193-01
320W-12V-DUAL-VOLT-PS
1
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6/6/2017
A
PRODUCTION RELEASE -
ADJUSTED POWER SUPPLIES,
REMOVED PART# 606-01285-01
9/6/2017
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
NEXT ASSY
USED ON
APPLICATION
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
INTERPRET GEOMETRIC
TOLERANCING PER:
MATERIAL
FINISH
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
RAW THRILLS, INC
TITLE:
SIZE
B
REV
WEIGHT:
SCALE: 1:22
UNLESS OTHERWISE SPECIFIED:
A
MG
SNOWBOARD-
MAIN-CAB-ASSY
SHEET 1 OF 1
SNOWBOARD-MAIN-CAB-ASSY
DO NOT SCALE DRAWING
DWG. NO.
Page 32
2
5
3
1
4
5
42.940
9.339
10.054
43.188
42.593
53.495
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6-6-2017
A
PRODUCTION RELEASE - REMOVED (2X)PART#600-01996-01
9/6/2017
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
COMPLETE-PED-ASSY
COMPLETE-PED-ASSY-REF-ONLY
1
2
606-01287-01
DECAL-PEDESTAL-FRONT-SNOWBOARD
1
3
606-01286-01
DECAL-PEDESTAL-BACK-SNOWBOARD
1
4
600-01994-01
GRIP-MAT-SNOWBOARD
1
5
600-01957-01
BRACKET-CONNECT-SNOWBOARD
2
SNOWBOARD-PED-ASSY
SNOWBOARD-PED-ASSY
1:8
A
8
7
6
5
3
4
SCALE
RELEASE DATE
2
SHEET
1
A
B
C
8
D
DRAWING NO.
TITLE
C
SIZE
6
7
5
3
4
2
REV
A
B
C
1
D
THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR
HEREWITH ARE NOT TO BE REPRODUCED, USED OR
OTHERWISE DISCLOSED IN WHOLE OR IN PART TO ANYONE
WITHOUT THE WRITTEN CONSENT OF RAW THRILLS, INC.
1 OF 1
RAW THRILLS, INC.
5441 FARGO AVENUE SKOKIE, IL. 60077
.003
1/2
HOLES:
ANGLES:
.015
.010
.005
X.X
X.XX
X.XXX
-
DATE
APPROVALS
CHECK
DESIGN
DRAWN
FINISH
MATERIAL
DO NOT SCALE THIS DRAWING
TOLERANCES UNLESS OTHERWISE SPECIFIED:
REQUIRED
NEXT ASSEMBLY
CADREF:
-
1
-
-
-
SNOWBOARD-PED-ASSY
Page 33
LEFT-ROTO-SIDE-PANEL-ASSY
5
3
9
4
1
12
6
2
8
7
13
40.998
46.861
8.125
RIGHT-ROTO-SIDE-PANEL-ASSY
5
4
3
11
12
1
10
2
7
6
13
QUANTITIES NEEDED FOR (1) LEFT ASSY & (1) RIGHT ASSY
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6-6-2017
A
PRODUCTION RELEASE - ADDED ITEM #7 AND 13, DEL
PART#S 603-00824-01, 603-00825-01, 606-01290-01,
606-01291-01, 606-01294-01, 606-01295-01
9/6/2017
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
603-00814-01
PANEL-ROTO-SIDE-SNOWBOARD
2
2
603-00826-01
PETG-ROTO-BASE-OUTSIDE-SNOWBOARD
2
3
603-00827-01
PETG-ROTO-BASE-INSIDE-SNOWBOARD
2
4
600-01985-01
BRACKET-ROTO-CORNER-SNOWBOARD
2
5
600-01986-01
BRACKET-ROTO-INSIDE-SNOWBOARD
2
6
600-01987-01
PLATE-ROTO-MOUNT-SNOWBOARD
2
7
600-02079-01
COVER-BRACKET-SNOWBOARD
2
8
606-01292-01
TRANSLITE-ROTO-OUTSIDE-LEFT-BASE-SNOWBOARD
1
9
606-01296-01
TRANSLITE-ROTO-INSIDE-LEFT-BASE-SNOWBOARD
1
10
606-01293-01
TRANSLITE-ROTO-OUTSIDE-RIGHT-BASE-SNOWBOARD
1
11
606-01297-01
TRANSLITE-ROTO-INSIDE-RIGHT-BASE-SNOWBOARD
1
12
WHITE-LEDS-BASE-ROTO-SIDE
75CM-WHITE-LED-STRIP-W-TAPE
2
13
600-01996-01 Roto Mount Base Bracket
BRACKET-ROTO-BASE-MOUNT-SNOWBOARD
2
SNOWBOARD-ROTO-LEFT/RT-SIDE-
PANEL-ASSY
SNOWBOARD-ROTO-SIDE-PANEL-ASSY
1:8
A
8
7
6
5
3
4
SCALE
RELEASE DATE
2
SHEET
1
A
B
C
8
D
DRAWING NO.
TITLE
C
SIZE
6
7
5
3
4
2
REV
A
B
C
1
D
THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR
HEREWITH ARE NOT TO BE REPRODUCED, USED OR
OTHERWISE DISCLOSED IN WHOLE OR IN PART TO ANYONE
WITHOUT THE WRITTEN CONSENT OF RAW THRILLS, INC.
1 OF 1
RAW THRILLS, INC.
5441 FARGO AVENUE SKOKIE, IL. 60077
.003
1/2
HOLES:
ANGLES:
.015
.010
.005
X.X
X.XX
X.XXX
-
DATE
APPROVALS
CHECK
DESIGN
DRAWN
FINISH
MATERIAL
DO NOT SCALE THIS DRAWING
TOLERANCES UNLESS OTHERWISE SPECIFIED:
REQUIRED
NEXT ASSEMBLY
CADREF:
-
1
-
-
-
SNOWBOARD-ROTO-SIDE-PANEL-ASSY
Page 34
7
8
6
1
3
2
5
4
5
30.513
7.614
20.726
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6-3-2017
A
PRODUCTION RELEASE - REMOVED LED BACKLIGHTING,
PETG AND TRANSLITE - ADDED ITEM# 6, 7 AND 8
9/6/2017
ITEM
NO.
PART NUMBER
DESCRIPTION
QTY.
1
603-00815-01
HOUSING-CONTROL-ROTO-SNOWBOARD
1
2
603-00821-01
PETG-CONTROL-PANEL-SNOWBOARD
1
3
606-01298-01
TRANSLITE-CONTROL-PANEL-SNOWBOARD
1
4
702-00090-01
LARGE RND - WHITE-START 'X'- PUSH-BUTTON
1
5
702-00089-01
LARGE RND - WHITE - PUSH-BUTTON-LEFT-
ARROW
2
6
600-02080-01 Blower Plate
PLATE-VENT-BLOWER-SNOWBOARD
1
7
606-01350-01
DECAL-LEFT-BLOWER-SNOWBOARD
1
8
606-01351-01
DECAL-RIGHT-BLOWER-SNOWBOARD
1
SNOWBOARD-ROTO-CONTROL-
PANEL-ASSY
SNOWBOARD-ROTO-CONTROL-PANEL-ASSY
1:6
A
8
7
6
5
3
4
SCALE
RELEASE DATE
2
SHEET
1
A
B
C
8
D
DRAWING NO.
TITLE
C
SIZE
6
7
5
3
4
2
REV
A
B
C
1
D
THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR
HEREWITH ARE NOT TO BE REPRODUCED, USED OR
OTHERWISE DISCLOSED IN WHOLE OR IN PART TO ANYONE
WITHOUT THE WRITTEN CONSENT OF RAW THRILLS, INC.
1 OF 1
RAW THRILLS, INC.
5441 FARGO AVENUE SKOKIE, IL. 60077
.003
1/2
HOLES:
ANGLES:
.015
.010
.005
X.X
X.XX
X.XXX
-
DATE
APPROVALS
CHECK
DESIGN
DRAWN
FINISH
MATERIAL
DO NOT SCALE THIS DRAWING
TOLERANCES UNLESS OTHERWISE SPECIFIED:
REQUIRED
NEXT ASSEMBLY
CADREF:
-
1
-
-
-
SNOWBOARD-ROTO-CONTROL-PANEL-ASSY
Page 35
10
6 9
1
8
5
3
4
5
7
2
2
41.159
6.314
29.473
A
A
21.313
VIEW A-A
43
2
3
2
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6-6-2017
A
PRODUCTION RELEASE - CHANGED LEDS FROM RGB TO BLUE
9/6/2017
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
600-01977-01
BRACKET-MARQUEE-BASE-SNOWBOARD
1
2
600-01978-01
CLIP-BOARD-MOUNT-SNOWBOARD
2
3
600-01980-01
STRUT-MARQUEE-SNOWBOARD
2
4
600-01981-01
BRACKET-STRUT-MARQUEE-SNOWBOARD
1
5
603-00817-01
PANEL-MARQUEE-FORMED-SNOWBOARD
1
6
603-00819-01
ACRYLIC-GRAY-MARQUEE-SNOWBOARD
1
7
606-01284-01
DECAL-BOARD-MARQUEE-SNOWBOARD
1
8
85cm LED Strip (WHITE) 85cm LED Strip (WHITE)
2
9
100cm LED Strip (BLUE) 100cm LED Strip (BLUE)
1
10
X-GAMES-MARQUEE-ASSY X-GAMES-MARQUEE-ASSY
1
SNOWBOARD-MARQUEE-ASSY
SNOWBOARD-MARQUEE-ASSY
1:8
A
8
7
6
5
3
4
SCALE
RELEASE DATE
2
SHEET
1
A
B
C
8
D
DRAWING NO.
TITLE
C
SIZE
6
7
5
3
4
2
REV
A
B
C
1
D
THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR
HEREWITH ARE NOT TO BE REPRODUCED, USED OR
OTHERWISE DISCLOSED IN WHOLE OR IN PART TO ANYONE
WITHOUT THE WRITTEN CONSENT OF RAW THRILLS, INC.
1 OF 1
RAW THRILLS, INC.
5441 FARGO AVENUE SKOKIE, IL. 60077
.003
1/2
HOLES:
ANGLES:
.015
.010
.005
X.X
X.XX
X.XXX
-
DATE
APPROVALS
CHECK
DESIGN
DRAWN
FINISH
MATERIAL
DO NOT SCALE THIS DRAWING
TOLERANCES UNLESS OTHERWISE SPECIFIED:
REQUIRED
NEXT ASSEMBLY
CADREF:
-
1
-
-
-
SNOWBOARD-MARQUEE-ASSY
Page 36
3
2
6
1
5
4
5
6
14.150
5.007
15.749
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6-6-2017
A
PRODUCTION RELEASE
9/6/2017
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
603-00816-01
LIGHTBOX-MOLDED-X-SNOWBOARD
1
2
603-00823-01
PETG-X-SNOWBOARD
1
3
606-01289-01
SNOWBOARD-X-TRANSLITE
1
4
600-01979-01
BRACKET-X-MOUNT-SNOWBOARD
1
5
500-00205-01
White LED Superpuck PCB-36LEDS
2
6
30CM-WHITE-LED-STRIP
30cm Flexible LED Strip (White)
2
SNOWBOARD-X-MARQUEE-ASSY
SNOWBOARD-X-MARQUEE-ASSY
1:4
A
8
7
6
5
3
4
SCALE
RELEASE DATE
2
SHEET
1
A
B
C
8
D
DRAWING NO.
TITLE
C
SIZE
6
7
5
3
4
2
REV
A
B
C
1
D
THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR
HEREWITH ARE NOT TO BE REPRODUCED, USED OR
OTHERWISE DISCLOSED IN WHOLE OR IN PART TO ANYONE
WITHOUT THE WRITTEN CONSENT OF RAW THRILLS, INC.
1 OF 1
RAW THRILLS, INC.
5441 FARGO AVENUE SKOKIE, IL. 60077
.003
1/2
HOLES:
ANGLES:
.015
.010
.005
X.X
X.XX
X.XXX
-
DATE
APPROVALS
CHECK
DESIGN
DRAWN
FINISH
MATERIAL
DO NOT SCALE THIS DRAWING
TOLERANCES UNLESS OTHERWISE SPECIFIED:
REQUIRED
NEXT ASSEMBLY
CADREF:
-
1
-
-
-
SNOWBOARD-X-MARQUEE-ASSY
Page 37
2
1
23.750
6.349
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6-6-2017
A
PRODUCTION RELEASE
9/6/2017
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
603-00818-01
REFLECTOR-MARQUEE-SNOWBOARD
1
2
60CM-WHITE-LED-STRIP
60cm LED Strip (WHITE)
3
SNOWBOARD-
MARQUEE=REFLECTOR-ASSY
SNOWBOARD-MARQUEE-REFLECTOR-ASSY
1:3
A
8
7
6
5
3
4
SCALE
RELEASE DATE
2
SHEET
1
A
B
C
8
D
DRAWING NO.
TITLE
C
SIZE
6
7
5
3
4
2
REV
A
B
C
1
D
THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR
HEREWITH ARE NOT TO BE REPRODUCED, USED OR
OTHERWISE DISCLOSED IN WHOLE OR IN PART TO ANYONE
WITHOUT THE WRITTEN CONSENT OF RAW THRILLS, INC.
1 OF 1
RAW THRILLS, INC.
5441 FARGO AVENUE SKOKIE, IL. 60077
.003
1/2
HOLES:
ANGLES:
.015
.010
.005
X.X
X.XX
X.XXX
-
DATE
APPROVALS
CHECK
DESIGN
DRAWN
FINISH
MATERIAL
DO NOT SCALE THIS DRAWING
TOLERANCES UNLESS OTHERWISE SPECIFIED:
REQUIRED
NEXT ASSEMBLY
CADREF:
-
1
-
-
-
SNOWBOARD-MARQUEE-REFLECTOR-ASSY
Page 38
2
3
1
5.167
25.046
41.340
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6-6-2017
A
PRODUCTION RELEASE
9/6/2017
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
MT42W-267A-SNOWBOARD
MAKVISION 42" LCD
1
2
608-00227-01
42-Monitor_Frame_Assy_Weldement
1
3
600-00073-01
42" LCD Display Glass (Tempered)
1
SNOWBOARD-LCD-ASSY
SNOWBOARD-LCD-ASSY
1:6
A
8
7
6
5
3
4
SCALE
RELEASE DATE
2
SHEET
1
A
B
C
8
D
DRAWING NO.
TITLE
C
SIZE
6
7
5
3
4
2
REV
A
B
C
1
D
THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR
HEREWITH ARE NOT TO BE REPRODUCED, USED OR
OTHERWISE DISCLOSED IN WHOLE OR IN PART TO ANYONE
WITHOUT THE WRITTEN CONSENT OF RAW THRILLS, INC.
1 OF 1
RAW THRILLS, INC.
5441 FARGO AVENUE SKOKIE, IL. 60077
.003
1/2
HOLES:
ANGLES:
.015
.010
.005
X.X
X.XX
X.XXX
-
DATE
APPROVALS
CHECK
DESIGN
DRAWN
FINISH
MATERIAL
DO NOT SCALE THIS DRAWING
TOLERANCES UNLESS OTHERWISE SPECIFIED:
REQUIRED
NEXT ASSEMBLY
CADREF:
-
1
-
-
-
SNOWBOARD-LCD-ASSY
Page 39
1
3
3
2
4
10.000
14.814
2.992
2.064
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6-6-2017
A
PRODUCTION RELEASE - ADDED (2X)
BLOWER PCBs AND 5V REG
9/6/2017
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
500-00040-01
RIO-board
1
2
600-02069-01
RIO MOUNTING-PLATE (w/ BLOWER (2X) and
SwREG- PCB)
1
3
500-00075-01
Snow Blower PCB
2
4
500-00194-01
5V, 5A Switching Regulator (12V input)
1
SNOWBOARD-RIO-HARDWARE-ASSY
SNOWBOARD-RIO-HARDWARE-ASSY
1:3
A
8
7
6
5
3
4
SCALE
RELEASE DATE
2
SHEET
1
A
B
C
8
D
DRAWING NO.
TITLE
C
SIZE
6
7
5
3
4
2
REV
A
B
C
1
D
THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR
HEREWITH ARE NOT TO BE REPRODUCED, USED OR
OTHERWISE DISCLOSED IN WHOLE OR IN PART TO ANYONE
WITHOUT THE WRITTEN CONSENT OF RAW THRILLS, INC.
1 OF 1
RAW THRILLS, INC.
5441 FARGO AVENUE SKOKIE, IL. 60077
.003
1/2
HOLES:
ANGLES:
.015
.010
.005
X.X
X.XX
X.XXX
-
DATE
APPROVALS
CHECK
DESIGN
DRAWN
FINISH
MATERIAL
DO NOT SCALE THIS DRAWING
TOLERANCES UNLESS OTHERWISE SPECIFIED:
REQUIRED
NEXT ASSEMBLY
CADREF:
-
1
-
-
-
SNOWBOARD-RIO-HARDWARE-ASSY
Page 40
2
1
6.863
6.105
7.736
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6-6-2017
A
PRODUCTION RELEASE
9/6/2017
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
600-01983-01
SNOWBOARD-BRACKET-BLOWER
1
2
604-00022-01
Johnson Blower
1
SNOWBOARD-BLOWER-ASSY
SNOWBOARD-BLOWER-ASSY
1:2
A
8
7
6
5
3
4
SCALE
RELEASE DATE
2
SHEET
1
A
B
C
8
D
DRAWING NO.
TITLE
C
SIZE
6
7
5
3
4
2
REV
A
B
C
1
D
THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR
HEREWITH ARE NOT TO BE REPRODUCED, USED OR
OTHERWISE DISCLOSED IN WHOLE OR IN PART TO ANYONE
WITHOUT THE WRITTEN CONSENT OF RAW THRILLS, INC.
1 OF 1
RAW THRILLS, INC.
5441 FARGO AVENUE SKOKIE, IL. 60077
.003
1/2
HOLES:
ANGLES:
.015
.010
.005
X.X
X.XX
X.XXX
-
DATE
APPROVALS
CHECK
DESIGN
DRAWN
FINISH
MATERIAL
DO NOT SCALE THIS DRAWING
TOLERANCES UNLESS OTHERWISE SPECIFIED:
REQUIRED
NEXT ASSEMBLY
CADREF:
-
1
-
-
-
SNOWBOARD-BLOWER-ASSY
Page 41
5.875
3.375
1.969
1
5
4
3
2
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
PROTO RELEASE
7/28/2016
A
PRODUCTION RELEASE
9/6/2017
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
600-01681-01
PLATE, AC - LINE FILTER,CIRCUIT BREAKER, ON/OFF
SW
1
2
Power Inlet Receptacle
IEC Appliance Inlet, Screw-on Mounting, Front Side,
Quick-connect, 10A
1
3 T9-611-5A
5A-Circuit Breaker, Snap-in type, Fuseholder style, 1
pole (Schurter #4404.0007)
1
4
1832-33-12
AC-SWITCH-15AMP-125V-HEILAND-ELECT
1
5
Ring and Spade Tongue
Terminal
Ring and Spade Tongue Terminal (#8 Screw)
1
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
NEXT ASSY
USED ON
APPLICATION
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
INTERPRET GEOMETRIC
TOLERANCING PER:
MATERIAL
FINISH
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
RAW THRILLS, INC
TITLE:
SIZE
B
REV
WEIGHT:
SCALE: 1:1.5
UNLESS OTHERWISE SPECIFIED:
A
MG
SNOWBOARD-
POWER-PLATE-ASSY
SHEET 1 OF 1
SNOWBOARD-POWER-PLATE-ASSY
DO NOT SCALE DRAWING
DWG. NO.
Page 42
2
3
1
8.500
8.500
4.150
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6-6-2017
A
PRODUCTION RELEASE
9/6/2017
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
2-1-18-00-00-000
8” Woofer, 4 Ohm, Poly-Mica Cone
1
2
600-01995-01
GRILL-WOOFER-JP-55
1
3
FOAM INSULATION FOAM INSULATION
2
SNOWBOARD-WOOFER-ASSY
SNOWBOARD-WOOFER-ASSY
1:2
A
8
7
6
5
3
4
SCALE
RELEASE DATE
2
SHEET
1
A
B
C
8
D
DRAWING NO.
TITLE
C
SIZE
6
7
5
3
4
2
REV
A
B
C
1
D
THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR
HEREWITH ARE NOT TO BE REPRODUCED, USED OR
OTHERWISE DISCLOSED IN WHOLE OR IN PART TO ANYONE
WITHOUT THE WRITTEN CONSENT OF RAW THRILLS, INC.
1 OF 1
RAW THRILLS, INC.
5441 FARGO AVENUE SKOKIE, IL. 60077
.003
1/2
HOLES:
ANGLES:
.015
.010
.005
X.X
X.XX
X.XXX
-
DATE
APPROVALS
CHECK
DESIGN
DRAWN
FINISH
MATERIAL
DO NOT SCALE THIS DRAWING
TOLERANCES UNLESS OTHERWISE SPECIFIED:
REQUIRED
NEXT ASSEMBLY
CADREF:
-
1
-
-
-
SNOWBOARD-WOOFER-ASSY
Page 43
2
1
3
7.000
5.375
1.476
7.000
REVISIONS
ZONE
REV.
DESCRIPTION
DATE
APPROVED
1
QUOTATION RELEASE
6-6-2017
A
PRODUCTION RELEASE
9/6/2017
ITEM NO.
PART NUMBER
DESCRIPTION
QTY.
1
600-01982-01
PLATE-FAN-SNOWBOARD
1
2
820-00001-00
FAN, 120VAC,19/15W
1
3
800-00001-00
120mm Wire Fan Guard
1
SNOWBOARD-FAN-ASSY
SNOWBOARD-FAN-ASSY
1:2
A
8
7
6
5
3
4
SCALE
RELEASE DATE
2
SHEET
1
A
B
C
8
D
DRAWING NO.
TITLE
C
SIZE
6
7
5
3
4
2
REV
A
B
C
1
D
THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR
HEREWITH ARE NOT TO BE REPRODUCED, USED OR
OTHERWISE DISCLOSED IN WHOLE OR IN PART TO ANYONE
WITHOUT THE WRITTEN CONSENT OF RAW THRILLS, INC.
1 OF 1
RAW THRILLS, INC.
5441 FARGO AVENUE SKOKIE, IL. 60077
.003
1/2
HOLES:
ANGLES:
.015
.010
.005
X.X
X.XX
X.XXX
-
DATE
APPROVALS
CHECK
DESIGN
DRAWN
FINISH
MATERIAL
DO NOT SCALE THIS DRAWING
TOLERANCES UNLESS OTHERWISE SPECIFIED:
REQUIRED
NEXT ASSEMBLY
CADREF:
-
1
-
-
-
SNOWBOARD-FAN-ASSY
Page 44
1
4
3
2
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
33
32
ITEM
NO.
PART NUMBER
DESCRIPTION
QTY.
1
BOARD ASSEMBLY
1
2
LOWER BOARD MECH
1
3
BRAKE ASSEMBLY
1
4
POT ASSEMBLY
1
5
600-01962-01
LED BRACKET
2
6
500-00217-01
LED BOARD
2
7
600-01963-01
LED LENS
2
8
600-01961-01
FRAME BRACKET ASSEMBLY
1
9
600-01955-01
FRONT PEDESTAL COVER
1
10
600-01956-01
REAR PEDESTAL COVER
1
11
600-01348-01
STOP PAD
2
12
600-01349-01
STOP PAD HOLDER BRACKET
2
13
AS-3207
CURVED LIGHT ASSEMBLY A
2
14
AS-3171
CURVED LIGHT ASSEMBLY B
2
15
608-00226-01
PEDESTAL FRAME ASSEMBLY
1
16
600-01353-01
BRAKE PAN
1
17
600-01965-01
ROSTA PLATE
1
18
MMC 95649A247
UHMW WASHER
1
19
4" LEG LEVELER 1/2-13 THREAD
7
20
600-01351-01
LEG LEVELER PLATE
7
21
MMC 91101A229
1/4" SPLIT WASHER
44
22
MMC 91257A544
1/4-20 x 1 1/4 GRADE 8 HEX BOLT
44
23
MMC 90648A029
1/4-20 NYLOK
8
24
CASTER
4
25
MMC 91290A336
M6 X 25MM CAP SCREW
8
26
MMC 90631A411
10-32 NYLOK NUT
2
27
MMC 90128A241
1/4-20 X 3/8" CAP SCREW
8
28
MMC 91251A621
3/8-16 X 5/8" CAP SCREW
6
29
MMC 90108A417
3/8 X 1" OD WASHER
6
30
MMC 96075A211
1/4-20 X 1/2" TAMPERPROOF
SCREW
29
31
MMC 91290A516
M10 X 20MM CAP SCREW
6
32
MMC 91106A133
M10 INTERNAL TOOTH WASHER
6
33
MMC 90272A192
8-32 X 3/8" PAN HEAD PHILLIPS
SCREW
4
REV.
DESCRIPTION
DATE
1 of 4
MATERIAL:
FINISH:
PART NO.
RAW THRILLS INC.
SHEET
A
TOL: .X ±.030
.XX ±.015
.XXX ±.005
HOLES: +.002/-.000
ANGLES: ±0.5°
REV
B
SEE NOTES
RELEASED
9/8/17
SEE NOTES
PEDESTAL ASSEMBLY DRAWING
TITLE:
B
FIXED PART NUMBER OF ITEM 20
11/17/17
Page 45
1
2
3
4
5
6
7
8
9
10
11
12
BOARD ASSEMBLY
NOTES:
1) THE NUT HOLDING THE POT HOLDER BRACKET
SHOULD BE FULLY TIGHTENED AND THEN LOOSENED SLIGHTLY (ABOUT
45 DEGREES) TO ALLOW PLAY IN THE POT HOLDER BRACKET.
ITEM
NO.
PART NUMBER
DESCRIPTION
QTY.
1
600-01654-01
SNOW BOARD
WELDMENT
1
2
600-01958-01
PINCH GUARD FOAM
70"
3
600-01959-01
BOARD BASE FRAME
1
4
MMC
90044A139
5/16-18 X 2" ALLOY CAP
SCREW
4
5
MMC
91610A710
6MM X 26MM SLOTTED
SPRING PIN
4
6
600-01970-01
ROSTA DR-A 18 X 120
2
7
608-00228-01
1K POT AND NUT
1
8
MMC
90648A029
1/4-20 NYLOK NUT
23
9
600-01658-01
POT HOLDER BRACKET
1
10
600-01661-01
POT COUPLER
1
11
600-01657-01
ROSTA MOUNTING
BRACKET
2
12
600-01960-01
ANCHOR BRACKET
2
REV.
DESCRIPTION
DATE
2 of 4
MATERIAL:
FINISH:
PART NO.
RAW THRILLS INC.
SHEET
A
TOL: .X ±.030
.XX ±.015
.XXX ±.005
HOLES: +.002/-.000
ANGLES: ±0.5°
REV
B
SEE NOTES
RELEASED
9/8/17
SEE NOTES
PEDESTAL ASSEMBLY DRAWING
TITLE:
B
CHANGED PART NUMBER OF ITEM #7
11/7/17
Page 46
1
2
3
4
5
6
7
8
9
10
11
8
13
14
15
16
17
16
12
LOWER BOARD MECH
ITEM
NO.
PART NUMBER
DESCRIPTION
QTY.
1
600-01966-01
PIVOT MECH TOP PLATE
1
2
600-01967-01
PINCH GUARD DISC
1
3
600-01182-01
STOP PLATE
1
4
600-01183-01
BOTTOM MECH PLATE
1
5
600-01971-01
ROSTA DR-S 18 X 70
1
6
600-01322-01
CROSS ROLLER RING
1
7
600-01364-01
M12 FEMALE ROD END -
RIGHT HAND
1
8
MMC 90591A181
M12 RIGHT HAND NUT
2
9
600-01187-01
THREADED HEX TURNBUCKLE
1
10
MMC 93695A190
M12 LEFT HAND NUT
1
11
600-01363-01
M12 FEMALE ROD END - LEFT
HAND
1
12
MMC 91420A320
M5 X 10MM PHILLIPS FLAT
HEAD SCREW
6
13
MMC 91166A290
M12 WASHER
1
14
MMC 92005A220
M4 X 10MM PHILLIPS SCREW
2
15
1/2" CABLE CLAMP
2
16
MMC 91290A334
M6 X 35MM CAP SCREW
18
17
MMC 91290A336
M6 X 40MM CAP SCREW
8
REV.
DESCRIPTION
DATE
3 of 4
MATERIAL:
FINISH:
PART NO.
RAW THRILLS INC.
SHEET
A
TOL: .X ±.030
.XX ±.015
.XXX ±.005
HOLES: +.002/-.000
ANGLES: ±0.5°
REV
B
SEE NOTES
RELEASED
9/8/17
SEE NOTES
PEDESTAL ASSEMBLY DRAWING
TITLE:
B
NO CHANGES THIS SHEET
11/7/17
Page 47
1
2
7
9
6
3
4
5
8
1
2
3
4
5
6
7
8
DO NOT FULLY TIGHTEN THIS SCREW,
THE GEAR MUST BE FREE TO SPIN.
USE THREADLOCKER OR A
PATCH SCREW TO PREVENT
UNSCREWING
BRAKE ASSEMBLY
POT ASSEMBLY
ITEM
NO.
PART NUMBER
DESCRIPTION
QTY
1
604-00038-01
BRAKE AND 25MM HUB
1
2
600-01186-01
BRAKE BRACKET ASSY
1
3
600-01195-01
SMALL BRAKE BUSHING
1
4
MMC 91100A170
M10 FENDER WASHER
1
5
MMC 91290A522
M10 X 30MM CAP SCREW
1
6
600-01194-01
LARGE BRAKE BUSHING
1
7
600-01161-01
DRIVE GEAR
1
8
600-01317-01
MACHINE KEY 8MM X
8MM X 20MM
1
9
MMC 92313A192
SET SCREW
1
ITEM
NO.
PART NUMBER
DESCRIPTION
QTY
1
600-01964-01
POT BRACKET
1
2
600-01188-01
IDLER STUD
1
3
600-01161-01
DRIVE GEAR
1
4
MMC 91770A827
10-32 X 3/8 TRUSS HEAD
PHILLIPS SCREW
2
5
600-01567-01
SMALL POT GEAR
1
6
608-00219-01
5K POT AND NUT
1
7
MMC 92141A030
5/16 WASHER
1
8
MMC 91390A100
M3 X 6MM SET SCREW
1
REV.
DESCRIPTION
DATE
4 of 4
MATERIAL:
FINISH:
PART NO.
RAW THRILLS INC.
SHEET
A
TOL: .X ±.030
.XX ±.015
.XXX ±.005
HOLES: +.002/-.000
ANGLES: ±0.5°
REV
B
SEE NOTES
RELEASED
9/8/17
SEE NOTES
PEDESTAL ASSEMBLY DRAWING
TITLE:
B
CORRECTED PART NUMBER OF ITEM 6.
ADDED ITEMS 7 & 8. ADDED NOTE.
11/7/17
Page 48
Page 49
Issue Date: 2/22/19
SERVICE BULLETIN
IMPORTANCE: LOW
X Games Snowboarder™
Platform Separation from
Main Cabinet for Service
If there are additional questions, contact the Raw Thrills Hotline at (800) 753-2513.
Raw Thrills is releasing this bulletin to describe the preferred way to service the Platform
section of the game. There is no need to remove the Side Rails to service the Platform.
This procedure requires a second helper to lift/tilt the Main Cabinet backward while the
Platform is slid away from th Main Cabinet.
Required Tools:
- T-27 Tamperproof Torx Bit and Driver or the “L” key that was included with the game
in the original game parts bag
Procedure:
1) Turn off power to the game.
2) Raise all the leg levelers on the platform (7 total) to allow the castors to be used to roll
the Platform away from the Main Cabinet.
3) Remove the (6) ¼-20 tamperproof screws and washers (3 per side) on the platform side
of the brackets that join the Platform to the Main Cabinet, and the (8) ¼-20 tamperproof
screws and washers (4 per side) that attach the Side Rails to the Platform using a T-27
tamperproof tool as shown below. (7) sets of screws and washers are shown, the other
(7) are on the other side of the game.
Page 50
4) Have another person lift/tilt the Main Cabinet backward while the Platform is slid away
from the Main Cabinet about a foot. Do not lift more than about an inch to prevent
tipping. Set the Main Cabinet back down and unplug the harness from the back of the
Pedestal.
5) Have the other person lift/tilt the Main Cabinet backward again and fully pull the Platform
out from under the Side Rails of the Main Cabinet.
6) At this point easy access can be gained to either the front or rear areas by removing the
¼-20 screws using a T-27 tamperproof tool to allow removal of either the Front or Rear
Access Panels. The below illustration shows just the screws on the right side. The left
side is the mirror image.
7) After servicing the Platform, reverse steps 6 through 2 to reassemble the Pedestal to the
Main Cabinet.
Loading...