M U LT I C H A N N E L P O W E R V I D E O H U B
PowerCat 4
USER MANUAL
•
PowerCat 8
•
PowerCat 16
PowerCat Multi Channel Power Video Hub
• Provides camera power while receiving video transmission over one single 4-pair UTP
Cat5e/6 cable per channel
• Colour Video + Power up to 300m for 12VDC camera
• BNC output per channel to DVR
• RJ45 input per channel from camera
• PAL video format compatible
• Real-time transmission
• Exceptional interference rejection
• Built-in TVS for surge protection & ground loop i
• Lightning protection design Grade: III
• Wave Filter and Anti-Static Design
• Black galvanized housing
• Rack, wall mountable or desk installation
solation
Overview
The PowerCat is a multi channel video and power hybrid receiver that consolidates all CCTV
system cabling using standard EIA/TIA 568A/B structured building wiring. Designed for
installation in an IDF/Telecom Closet, MDF/Equipment Room or simply
PowerCat allows real time transmission of CCTV video and power signal via cost-effective
Unshielded Twisted Paired (UTP) cable. The included balun transmitters convert the source
power of 28VDC to regulated 12VDC to allow safe powering of a 12VDC camera at cable
distances of up to 300m. Superior interference rejection of the PowerCat allows video and
power signals to co-exist in the l
arge majority of applications.
desk mounted the
Cable Termination
The recommended cable for use with the PowerCat is unshielded Twisted Paired (UTP)
wiring 24AWG or better. Individually shielded pairs should be avoided, as they reduce the
operating range of the PowerCat drastically. Multi-pair cable (25-pair or more) with an
overall shield is acceptable. Video signals can coexist in the same wire bundle as
telephone, da
telephone punch-down block terminals, any bridge-taps, also called T-taps and any
resistive, capacitive or inductive devices MUST BE removed from the pair.
IMPORTANT - Check the format of your cable before starting termination and ensure
matching termination at both ends of the cable. Cables should be terminated as follows
using ei
ther T568A or T568B cable formats.
tacom, or low-voltages power circuits. While video may be routed through
2
Power and
Video
to Camera
BALUN
CAT5e/6 Cable
Termination
Video+ Video- Power- Power+
12345678
T568A: White Green Green White Orange Blue White Blue Orange White Brown Brown
T568B: White Orange Orange White Green Blue White Blue Green White Brown Brown
BNC
DVR
BNC RJ45
PowerCat
LED Indications
TRANSMITTER END RECEIVER END
Yellow LED ON: Overcurrent
Green LED ON: Power ON
Maximum Performance Chart
240vDC
The maximum performance of each
channel of the PowerCat is
determined by a combination of cable
distance and power requirements of
the camera. The maximum current
drain allowable at the maximum
cable run of 300m is 600ma.
Colour Camera with Cat5e / Cat6 24AWG cable
Maximum cable run Maximum Current drain at Camera
100M 1500mA
150m 1100mA
200m 850mA
250m 700mA
300m 600ma
3
Technical Specification
VIDEO Video Format PAL
Operating Frequency DC to 6MHz (-3db)
Max Distance UTP Category 5e (24AWG) Color: 300m
Common-mode/
Differential-mode rejection
Impedance UTP, RJ45 100 ohms
Attenuation 0.5 dB typ
WIRE TYPE Network Wiring One four-pair UTP Cat5e / Cat6 per channel
Category Type UTP Cat5e / Cat6
Impedance 100 ± 20 ohms
DC Loop Resistance 52 ohms per 1,000ft (18 ohms per 100m)
POWER Power Input 220VAC, 50Hz
Power Transmission 28VDC up to 300m via UTP Cat5e/6
Power Consumption PowerCat 16 300W
Power Consumption PowerCat 8 150W
Power Consumption PowerCat 4 100W
Output Power Per Channel Max 18.5W
CONNECTOR Video Input RJ45 Jack
Video Output Female BNC connector
PROTECTION Surge Protection Built-in Transient Voltage Suppressor(TVS)
Antistatic YES
MECHANICAL Dimensions PowerCat 16 430 x 237 x 66.5mm (excl. mounting bracket)
Dimensions PowerCat 8 290 x 212 x 44.5mm (excl. mounting bracket)
Dimensions PowerCat 4 290 x 212 x 44.5mm (excl. mounting bracket)
Housing Black galvanized
Body Color Black
Net Weight PowerCat 16 3890g
Net Weight PowerCat 8 2280g
Net Weight PowerCat 4 1360g
ENVIRONMENTAL Operating Temperature -25º ~ 75º C
Relative Humidity 0~95% (non-condensing)
Storage Temperature -40º ~ 150º C
15KHz to 5MHz 60 dB typ
(Regulated to 12vdc via balun)
Elite Security Products
Unit 7, Target Park, Shawbank Rd
Lakeside, Redditch B98 8YN
Telephone: 01527 51 51 50
Fax: 01527 51 51 43
email: info@espuk.com
Loading...