ESP MAGPRO-4i0O Installation Instructions Manual

MAGPRO-4i0O

EN54-18

!

Dimensions

176mm

!

Installation

IP40

-10°C ÷ +60°C

~320g

126mm 57mm

Indoor use

Outdoor use

Installation Instructions

!

ATTENTION

The MAGPRO-4i0O addressable module must be connected only to fire panels
from MAGPRO Series!

General Description

MAGPRO-4i0O is an addressable inputs module. The module monitors 4 analogue input signals.
MAGPRO-4i0O is powered on from the fire panel and can be controlled via the communication protocol.
The module is mounted is a separate small plastic box suitable for wall mounting.

Installation
Attention: Power off the loop circuit before installing the MAGPRO-4i0O addressable module!

1.󱆱Choose the proper place for installation of the module. Undo the screws of the cover and open the box.

2. Set the module address using MAGPRO-PROG programming tool. The address must be in the range from
1 to 250. The set address is one for the entire module.

3. Dismount the module’s PCB from the box bottom. Mark mounting holes on the installation surface. Drill
holes at the appropriate box side and run the cables to the module’s loop and input terminals.

4. Mount the box bottom at the place of installation. Mount the PCB back on place.

5. Connect the cables to the loop and input terminals of the module according the shown Connection
diagrams.

6. Close the cover of the plastic box and fix it to the bottom with the supplied screws.

7. Test the module for proper operation and LED indication.

TECHNICAL SPECIFICATIONS

Operating voltage . . . . . . . . . . . . . . . . . . . . . 15÷ 32 VDC

Consumption stand-by mode . . . . . . . . . . . . 300µА@27VDC

Nom. current consumption . . . . . . . . . . . . . . 330µА@27VDC

Current consumption with 1 LED on . . . . . . . 4mA

Current consumption with 2 LEDs on . . . . . . 7mA

Installation wires . . . . . . . . . . . . . . . . . . . . . . 0,4mm ÷ 2.0mm

Relative humidity . . . . . . . . . . . . . . . . . . . . . . ≤93% @ +40°C

Material (plastic) . . . . . . . . . . . . . . . . . . . . . . PS

Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gray

Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN54-18

2 2

1293-CPD-0258

Distributor: Elite Security Products Ltd, Unit 7 Target Park, Shawbank Road Lakeside, Redditch B98 8YN, UK http://www.espuk.com
Manufacturer: Teletek Electronics JSC, 14 Srebarna Str., 1407 Sofia, Bulgaria, http://www.teletek-electronics.com

18020168; RevC; 03/2017

1 2

Open the box

Address programming

- Use the cable with
5-pin terminal.

Line + >

Line - >

Izolator >

Line + >

Line - >

Up

Esc

Right

Modify

MAGPRO-

PROG

3

Mounting and Cable holes

Down

Enter

Possible places for
drilling of cable holes

Mounting
holes

4

Installation

Fix the
box on the
installation
surface

Run the
cables

!

LED Indication

The RED LED Lights on, when at least one of
the inputs is turned on (state ON)

The YELLOW LED Lights on, when at least one
of the inputs is in SHORT or OPEN condition,
i.e. there is an input in fault condition

The RED LED is blinking when communication
between the module and fire panel is running on

NOTE: In situations when both the red and yellow LEDs
are lighting on the actual color is recognized as orange

!

INPUTS Status

Status Description

SHORT

NORMAL

OPEN

* R - resistance between the input and GND
** I - current at the input

ON

Short circuit

Activation

Stand-by mode

Open circuit

R* I**

<13k

13k - 36k

36k - 90k

>90k

>54µA

38µA - 54µA

23µA - 38µA

<23µA

5

Connection diagrams

LED

(red-yellow)

Input 1 Input 2 Input 3 Input 4

56k

56k

ATTENTION: When you use the integrated short circuit isolation module connect one
of the “+Loop” loop lead to the “Isolator” terminal of the module.

56k

56k

Loop IN

Line +

Loop

Line -

Isolator

Line +

Isolator

Loop

Loop OUT

Line -

56k

56k

56k

56k