ESI TRIUMPH 2T-C28-24, TRIUMPH 2T-C40-24, TRIUMPH 2T-C28-30, TRIUMPH 2T-C40-30 Assembly Manual

ASSEMBLY GUIDE TRIUMPH ELECTRIC - 2-LEGASSEMBLY GUIDE TRIUMPH ELECTRIC - 2-LEG

6

1

7

1. ATTACH (I) FOOT PLATES AND (D) FEET TO BOTH (A&B) LEG
COLUMNS USING (N) M6X35 SCREWS (X8) BE SURE THE LONGER

SIDE OF THE FOOT GOES TOWARDS THE FRONT OF THE TABLE.

2. SET (B) LEG WITHOUT MOTOR UPRIGHT AND MANUALLY PUSH
DOWN TO THE LOWEST POSITION.

3. SET (A) LEG WITH MOTOR UPRIGHT.

4. ATTACH (F) CROSS CHANNEL TO THE (A&B) LEG COLUMNS USING
(M) M6X8 SCREWS (X4).

5. ATTACH THE (C) TOP SUPPORTS TO THE LEG COLUMNS USING
(O) M8 SCREWS (X4).

6. ATTACH THE (D) CROSS CHANNELS TO APPROPRIATE LENGTH AND TIGHTEN SECURELY
USING THE (L) M10 SCREWS (X4).

7. CONNECT THE 2 LEGS WITH THE CONNECT BAR (PULL THE CONNECT BAR TO THE
APPROPRIATE LENGTH).

8. ATTACH WORKSURFACE USING APPROPRIATE LENGTH SELF-TAPPING SCREWS. BE SURE

SCREWS ARE CORRECT LENGTH SO AS NOT TO PIERCE TOP OF WORKSURFACE.

9. ATTACH (J) KEYPAD/SWITCH AND (G) CONTROL UNIT UNDER WORKSURFACE IN
PREFERRED LOCATIONS.

10. ATTACH (H) LEG CABLE TO LEG WITH MOTOR ONLY.

11. CONNECT (J) KEYPAD SWITCH TO CONTROL UNIT. PLUG IN CONTROL UNIT TO POWER
SOURCE AND MOVE LEG DOWN TO THE LOWEST POSITION USING THE KEYPAD SWITCH.

12. TIGHTEN ALL SCREWS SECURELY.

13. MANAGE CABLES APPROPRIATELY AND IF NECESSARY, ADJUST LEVELING GLIDES ON
TABLE FEET TO LEVEL THE WORKSURFACE.

14. INITIALIZE LEGS: AFTER TABLE BASE IS FULLY ASSEMBLED AND
POWER CORD HAS BEEN PLUGGED IN, HOLD DOWN BOTH UP AND
DOWN BUTTONS ON KEYPAD/SWITCH FOR 5-10 SECONDS OR UNTIL
BOTH LEGS ARE IN THE LOWEST POSITION. TABLE BASE MUST BE

ZERO-SET BEFORE USE!

8

x1

CROSS

CHANNEL

esiergo.com | 800.833.3746

ASSEMBLY GUIDE TRIUMPH ELECTRIC - 2-LEG

PARTS USED IN ASSEMBLY

I

C

M

O

K

x2

TOP SUPPORT

x2

FOOT

PLATES

x1

LEG CABLE

x4

M8 SCREWS

x4

M6X8 SCREWS

x6

M5 SCREWS

SETTING TABLE TO ZERO

IMPORTANT! TABLE MUST BE ZERO-SET PRIOR TO USE.

1. PRESS BOTH BUTTONS AT THE SAME TIME FOR 5-10 SECONDS. THIS WILL ACTIVATE ZERO-SETTING MODE.

2. CONTINUE TO HOLD BOTH BUTTONS DOWN UNTIL BOTH LEGS ARE IN LOWEST POSITION.

3. THE TABLE IS NOW ZERO-SET AND READY TO USE.

IMPORTANT! HAND TIGHTEN KEYPAD SCREWS, DO NOT USE POWER TOOLS.

MAKE SURE ALL SCREWS ARE TIGHTENED ACCORDING TO THE TORQUE INFORMATION BELOW:

FEET SCREWS = 10NM
LEG SCREWS = 13NM
SUPPORT & CABLE BOX SCREWS = 6NM

J

x1

KEYPAD/SWITCH

G

x1

CONTROL UNIT

W/ POWER CORD

H

E

x1

CONNECT

BAR

B

x1

LEG

COLUMN

A

x1

LEG

COLUMN

W/

MOTOR

D

x2

FEET

F

L

x4

M10 SCREWS

N

x8

M6X35 SCREWS

PART NUMBER

2T-C28-24
2T-C28-30
2T-C40-24
2T-C40-30